Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Center Airbag Sensor Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Center Airbag Sensor Communication Stop Mode
Either condition is met:
  1. "Airbag" is not displayed on the "Bus Check" screen.
  2. "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or center airbag sensor assembly
  2. Center airbag sensor assembly CAN branch wire or connector
  3. Center airbag sensor assembly

WIRING DIAGRAM


C279373E02


INSPECTION PROCEDURE

NOTICE:
  1. The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)


    C222818E17
  1. Disconnect the J46 center airbag sensor assembly connector.

    1. for Column Shift Type: Click here
    2. for Floor Shift Type: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J46-13 (CANH) - J46-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)


    C222818E18
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J46-25 (E1) - Body ground
    Always
    Below 1 Ω
    J46-26 (E2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J46-21 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Center Airbag Sensor Assembly)
Result 
Result
Proceed to
OK (for Column Shift Type)
A
OK (for Floor Shift Type)
B
NG
C


B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)