Home › BODY › INTERIOR › ROOF HEADLINING (for Regular Cab)

ROOF HEADLINING (for Regular Cab) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL ROOF HEADLINING ASSEMBLY


B356935
  1. Place the roof headlining assembly into the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining assembly when placing it in the cabin.

  1. Attach the 3 clips to install the roof headlining assembly.

  1. Attach the 4 wire harness clamps and connect the connector to the front pillar LH.

  1. w/ EC Mirror:
    Connect the connector.



2. INSTALL COAT HOOK
  1. Using a T20 "TORX" driver, install the coat hook with the "TORX" screw.

  1. Attach the 2 claws to install the coat hook cap.



3. INSTALL VISOR HOLDER

HINT:
Use the same procedure to install the visor holder on the other side.

  1. Using a T20 "TORX" driver, install the visor holder with the "TORX "screw.



4. INSTALL VISOR ASSEMBLY LH
  1. w/ Vanity Light:
    Connect the connector.

  1. Attach the claw to install the visor assembly LH.

  1. Install the 2 screws.



5. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



6. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227101
  1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



7. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. Connect the connector.

  1. Using a T20 "TORX" driver, install the roof console box assembly with the 4 "TORX" screws.



    B356940
  1. Attach the 8 claws to install the roof console box base.



8. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. Attach the 5 clips to install the front quarter trim panel assembly LH.

  1. Install the 2 bolts.

  1. Connect the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



  1. Attach the 2 claws to close the shoulder belt anchor cover.


    B355509



    B355506
  1. Attach the claw to close the cover.



9. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



10. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH
  1. Attach the 7 clips to install the lower quarter trim panel assembly LH.



    B166849
  1. Twist the front seat outer belt assembly LH clockwise and connect it with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the 2 claws to install the cover.



11. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH
  1. Attach the 9 clips to install the lower quarter trim panel assembly RH.

  1. Install the jack assembly.

  1. Install the trim cover.



    B167430
  1. Twist the front seat outer belt assembly RH counterclockwise and connect it with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the 2 claws to install the cover.



12. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the clip to install the front pillar garnish LH.

  1. Install the bolt.



    B355362
  1. Attach the claw to close the cover.



13. INSTALL FRONT PILLAR GARNISH RH
  1. Attach the clip to install the front pillar garnish RH.

  1. Install the front assist grip sub-assembly to the front pillar garnish RH with the 2 bolts.



    B355365
  1. Attach the 2 claws to close the 2 assist grip covers.



14. INSTALL LUGGAGE COMPARTMENT BOX RH
  1. Install the luggage compartment box RH with the 4 clips.



15. INSTALL LUGGAGE COMPARTMENT BOX LH
  1. Attach the 3 claws to install the luggage compartment box LH.

  1. Install the 2 clips.



16. INSTALL UPPER BACK PANEL GARNISH
  1. Attach the 10 clips to install the upper back panel garnish.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip LH.



18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



19. INSTALL COWL SIDE TRIM BOARD LH
  1. Attach the 2 clips to install the cowl side trim board LH.

  1. Install the nut.



20. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



21. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Attach the 6 claws and 3 clips to install the front door scuff plate LH.



22. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



23. INSTALL FRONT SEAT ASSEMBLY (for Center Seat)
(Click here)


24. INSTALL FRONT SEAT ASSEMBLY
(Click here)


25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



26. CHECK SRS WARNING LIGHT
(Click here)