Home › BODY › INTERIOR › ROOF HEADLINING (for Regular Cab)

ROOF HEADLINING (for Regular Cab) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT SEAT ASSEMBLY
(Click here)


4. REMOVE FRONT SEAT ASSEMBLY (for Center Seat)
(Click here)


5. REMOVE FRONT DOOR SCUFF PLATE LH


B165843
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.



6. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



7. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the nut.

  1. Detach the 2 clips and remove the cowl side trim board LH.



8. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



11. REMOVE UPPER BACK PANEL GARNISH


B164740
  1. Detach the 10 clips and remove the upper back panel garnish.



12. REMOVE LUGGAGE COMPARTMENT BOX LH


B164747
  1. Remove the 2 clips.

  1. Detach the 3 claws and remove the luggage compartment box LH.



13. REMOVE LUGGAGE COMPARTMENT BOX RH


B164748
  1. Remove the 4 clips and luggage compartment box RH.



14. REMOVE FRONT PILLAR GARNISH LH


    B355361E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B355363
  1. Remove the bolt.

  1. Detach the clip and remove the front pillar garnish LH.



  1. Protect the curtain shield airbag assembly.



      B165709E07
    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.

      Text in Illustration 
      *1
      Adhesive Tape
      *2
      Protective Cover
      *3
      Curtain Shield Airbag Assembly



15. REMOVE FRONT PILLAR GARNISH RH


    B355364E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



    B355366
  1. Remove the 2 bolts and front assist grip sub-assembly from the front pillar garnish RH.



    B355367
  1. Detach the clip and remove the front pillar garnish RH.

  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



16. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165729
  1. Detach the 2 claws and remove the cover.



    B165728
  1. Loosen the bolt and disconnect the front seat outer belt assembly LH.



    B165710
  1. Detach the 7 clips and remove the lower quarter trim panel assembly LH.



17. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH


B164750
  1. Detach the 2 claws and remove the cover.



    B164749
  1. Loosen the bolt and disconnect the front seat outer belt assembly RH.



    B355510
  1. Push the 2 locks and remove the trim cover.

  1. Remove the jack assembly.



    B355511
  1. Detach the 9 clips and remove the lower quarter trim panel assembly RH.



18. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH


    B355505E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and open the cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the 2 claws and open the shoulder belt anchor cover.



  1. Loosen the bolt and disconnect the front seat outer belt assembly LH.


    B355508



    B355507
  1. Remove the 2 bolts.

  1. Detach the 5 clips and remove the front quarter trim panel assembly LH.



19. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



20. REMOVE ROOF CONSOLE BOX ASSEMBLY


    B356939E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 8 claws and remove the roof console box base.

    HINT:
    Tape the screwdriver tip before use.



    B356941
  1. Using a T20 "TORX" driver, remove the 4 "TORX" screws and remove the roof console box assembly.

  1. Disconnect the connector.



21. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227021
  1. Slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to detach the 2 claws from the roof headlining, and then detach the 2 claws of the inner rear view mirror stay holder cover from the mirror and remove the inner rear view mirror stay holder cover.



22. REMOVE VISOR ASSEMBLY LH


B355481
  1. Remove the 2 screws.

  1. Detach the claw and remove the visor assembly LH.



    B355482
  1. w/ Vanity Light:
    Disconnect the connector.



23. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



24. REMOVE VISOR HOLDER

HINT:
Use the same procedure to remove the visor holder on the other side.



    B165713
  1. Using a T20 "TORX" driver, remove the "TORX" screw and visor holder.



25. REMOVE COAT HOOK


    B355483E01
  1. Using a screwdriver, detach the 2 claws and remove the coat hook cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



    B355485
  1. Using a T20 "TORX" driver, remove the "TORX" screw and coat hook.



26. REMOVE ROOF HEADLINING ASSEMBLY


    B167283
  1. w/ EC Mirror:
    Disconnect the connector.



    B355487
  1. Disconnect the connector and detach the 4 wire harness clamps from the front pillar LH.



    B355512
  1. Detach the 3 clips and remove the roof headlining assembly.



    B355513
  1. Take out the roof headlining assembly from the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining assembly when taking it out.