Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Illumination Circuit

for Preparation Click here


WIRING DIAGRAM


E282220E01


INSPECTION PROCEDURE

HINT:
Inspect the bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (ILLUMINATION LIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Relay for Interior Light Auto Cut Function
    DOME relay
    ON or OFF
    -

    Result 
    Result
    Proceed to
    OK
    A
    NG (Only transponder key light does not turn on)
    B
    NG (Only foot light does not turn on)
    C
    NG (Only roof console light does not turn on)
    D



B
Go to step 2

C
Go to step 4

D
Go to step 6
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT TRANSPONDER KEY AMPLIFIER
E145066E08
  1. Remove the transponder key amplifier (Click here).

  1. Connect the battery's positive (+) lead to terminal 2 (ILL+) and the negative (-) lead to terminal 6 (ILL-), and then check that the light turns on.

    OK:
    Transponder key light turns on.



NG
REPLACE TRANSPONDER KEY AMPLIFIER (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - MAIN BODY ECU AND BATTERY)

E146732E03

  1. Disconnect the J20 amplifier connector.

  1. Disconnect the DD ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J20-2 (ILL+) - Body ground
    Battery saving control (interior light auto cut function) not operating
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J20-6 (ILL-) - DD-51 (ILE)
    Always
    Below 1 Ω
    J20-6 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.INSPECT FOOT LIGHT
E146733E01
  1. Remove the foot light (Click here).

  1. Connect the battery's positive (+) lead to terminal 2 and the negative (-) lead to terminal 1, and then check that the light turns on.

    OK:
    Foot light turns on.



NG
REPLACE FOOT LIGHT (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FOOT LIGHT - MAIN BODY ECU AND BATTERY)
E146734E01
  1. Disconnect the J51 light connector.

  1. Disconnect the DD ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J51-1 - Body ground
    Battery saving control (interior light auto cut function) not operating
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J51-2 - DD-51 (ILE)
    Always
    Below 1 Ω
    J51-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.INSPECT ROOM LIGHT SWITCH
E282224E01
  1. Remove the room light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (FCTY) - 11 (FLMP)
    Room light switch DOOR
    Below 1 Ω



NG
REPLACE ROOM LIGHT SWITCH (Click here)
OK


7.INSPECT ROOF CONSOLE BOX ASSEMBLY
E146741E01
  1. Remove the roof console box (Click here).

  1. Roof console box switch is DOOR.

  1. Connect the battery's positive (+) lead to terminal 2 (B) and the negative (-) lead to terminal 1 (CTY), and then check that the light turns on.

    OK:
    Map light turns on.



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX - MAIN BODY ECU AND BATTERY)
E150613E01
  1. Disconnect the W7 box connector.

  1. Disconnect the DD ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    W7-2 (B) - Body ground
    Battery saving control (interior light auto cut function) not operating
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    W7-1 (CTY) - DD-51 (ILE)
    Room light switch DOOR
    Below 1 Ω
    W7-1 (CTY) - Body ground
    Room light switch DOOR
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU