Home › BODY › SEAT › FRONT SEATBACK HEATER (for Manual Seat)

FRONT SEATBACK HEATER (for Manual Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. INSTALL FRONT SEATBACK HEATER ASSEMBLY RH
  1. Set the front seatback heater assembly RH on the separate type front seatback cover.



    B356060
  1. Using a tacker, install the front seatback heater assembly RH to the separate type front seatback cover with 8 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
  1. Set the separate type front seatback cover in place.

  1. Attach the 4 claws to install the 2 front seat headrest supports.



    B354566E01
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *a
    Cutout



    B356059E01
  1. Attach the 6 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.

  1. Attach the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after attach the 2 hooks.
    3. Attach the 2 hooks securely.


    1. Slide each hook to attach them.

    2. Install the 4 clips.



    B356808
  1. Close the 2 fasteners.

  1. Pass the 2 wire harnesses through the separate type front seatback cover.

  1. Detach the hook.



3. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. When reusing a bolt:

    1. Clean the threads of the bolt with non-residue solvent.

    2. Apply adhesive to the threads of the bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



    B356054
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    B356053E01
  1. Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly RH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp

  1. Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly RH.

  1. Connect the connector.



4. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD RH


    B356065
  1. Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield RH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



5. INSTALL FRONT SEAT CUSHION SHIELD RH


    B356066E01
  1. Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield RH.

  1. Install the 3 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the 2 rubber bands.



6. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
  1. Attach the claw to install the reclining adjuster release handle RH.



7. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the driver seat (Click here).