Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat) > REMOVAL

for Preparation Click here


CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. If the side airbag was deployed, replace the front seat airbag assembly LH, front seat back cover and front seat frame with adjuster assembly with the necessary parts in accordance with the extent of the collision damage.
  3. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)


4. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
  1. Raise the reclining adjuster release handle LH to reveal the claw.



    B354549E01
  1. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



5. REMOVE FRONT SEAT CUSHION SHIELD LH


    B354550
  1. Disconnect the 2 rubber bands.



    B354551E01
  1. Remove the 3 screws.

  1. Detach the guide, clip and 2 claws as indicated by the arrows in the order shown in the illustration to remove the front seat cushion shield LH.



6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


  1. for Manual Seat:



      B354553
    1. Detach the 2 hooks of the separate type front seat cushion cover.



    2. B354554E01
    3. Disconnect the connector and detach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



    4. B354555
    5. Detach the wire harness clamp.

    6. Remove the nut and front seat inner belt assembly LH.



  1. for Power Seat:



      B354885E01
    1. Detach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



    2. B354886
    3. Disconnect the connector and detach the wire harness clamp.

    4. Remove the nut and front seat inner belt assembly LH.



7. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    B355848
  1. Disconnect the connector and detach the wire harness clamp.

  1. Remove the nut and front seat inner belt assembly RH.



8. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354556
  1. Remove the 2 screws.

  1. Detach the guide in the direction indicated by the arrow shown in the illustration to remove the front inner No. 1 seat cushion shield LH.



9. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    B354558
  1. w/ Seat Heater System:

    1. Disconnect the connector.

    2. Detach the wire harness clamp to disconnect the wire harness of the front seatback heater assembly RH.



    B354559E01
  1. Detach the connector clamp and 3 wire harness clamps to disconnect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp



    B354560
  1. Remove the 4 bolts and separate type front seatback assembly.



10. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B354561
  1. Detach the hook.



    B354562
  1. Pull out the wire harness from the separate type front seatback cover.



    B354563
  1. Open the 2 fasteners.



    B354564
  1. Detach the 2 hooks.

    1. Remove the 4 clips.

    2. Slide each hook to detach them.

  1. Pull out the 4 straps of the separate type front seatback cover from the separate type front seatback pad.



    B354568E01
  1. Detach the 6 fasteners to remove the separate type front seatback cover from the separate type front seatback pad.
    Text in Illustration 
    *1
    Fastener



    B354565
  1. Remove the 2 hog rings.



    B354567
  1. Detach the 4 claws to remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover from the separate type front seatback pad.



11. REMOVE SEPARATE TYPE FRONT SEATBACK PAD
  1. Remove the separate type front seatback pad from the front seatback frame sub-assembly LH.



12. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH


    B355990
  1. Detach the 2 clamps from the front seatback main frame sub-assembly.

  1. Remove the 2 nuts and front seat airbag assembly LH.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the front seat back main frame sub-assembly is not deformed. If it is, replace it with a new one.