Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the front seat back main frame sub-assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly LH with 2 new nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Attach the 2 clamps to the front seatback main frame sub-assembly.



2. INSTALL SEPARATE TYPE FRONT SEATBACK PAD
  1. Install the separate type front seatback pad to the front seatback frame sub-assembly LH.



3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
  1. Set the separate type front seatback cover in place.

  1. Attach the 4 claws to install the 2 front seat headrest supports.



    B354566E01
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *a
    Cutout



    B354568E01
  1. Attach the 6 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.

  1. Attach the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after attaching the 2 hooks.
    3. Attach the 2 hooks securely.


    1. Slide each hook to attach them.

    2. Install the 4 clips.



    B356803
  1. Close the 2 fasteners.

  1. Pass the wire harness through the separate type front seatback cover.

  1. Attach the hook.



4. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. When reusing a bolt:

    1. Clean the threads of the bolt with non-residue solvent.

    2. Apply adhesive to the threads of the bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



    B354560
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    B354559E01
  1. Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp

  1. w/ Seat Heater System:

    1. Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly RH.

    2. Connect the connector.



5. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354557
  1. Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


  1. for Manual Seat:



      B356070E01
    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor of the front seat inner belt assembly LH to overlap the protruding part of the separate type front seat cushion spring assembly.

      Text in Illustration 
      *1
      Protruding Part

    2. Attach the wire harness clamp.



    3. B354554E01
    4. Connect the connector and attach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp

    5. Attach the 2 hooks of the separate type front seat cushion cover.



  1. for Power Seat:



      B356091E01
    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor of the front seat inner belt assembly LH to overlap the protruding part of the separate type front seat cushion spring assembly.

      Text in Illustration 
      *1
      Protruding Part

    2. Attach the wire harness clamp and connect the connector.



    3. B354885E01
    4. Attach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



7. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    B356071E01
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor of the front seat inner belt assembly RH to overlap the protruding part of the separate type front seat cushion spring assembly.

    Text in Illustration 
    *1
    Protruding Part

  1. Connect the connector and attach the connector clamp.



8. INSTALL FRONT SEAT CUSHION SHIELD LH


    B354552E01
  1. Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield LH.

  1. Install the 3 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the 2 rubber bands.



9. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Attach the claw to install the reclining adjuster release handle LH.



10. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).