FRONT POWER SEAT MOTOR ASSEMBLY > REMOVAL |
| 1. REMOVE FRONT SEAT ASSEMBLY |
| 2. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side) |
for Manual Seat:
![]() |
Detach the 2 hooks of the separate type front seat cushion cover.
![]() |
Disconnect the connector and detach the connector clamp and 3 wire harness clamps.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
Detach the wire harness clamp.
Remove the nut and front seat inner belt assembly LH.
for Power Seat:
![]() |
Detach the connector clamp and 3 wire harness clamps.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
Disconnect the connector and detach the wire harness clamp.
Remove the nut and front seat inner belt assembly LH.
| 3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side) |
![]() |
Disconnect the connector and detach the wire harness clamp.
Remove the nut and front seat inner belt assembly RH.
| 4. REMOVE SEAT POSITION AIRBAG SENSOR |
![]() |
for Manual Seat:
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.
![]() |
for Power Seat:
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.
| 5. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Disconnect the 2 rubber bands.
![]() |
Remove the 2 screws.
Detach the guide, clip and 2 claws as indicated by the arrows in the order shown in the illustration.
![]() |
w/o Leg Support Adjustment Switch:
Detach the clamp and disconnect the 2 connectors to remove the front seat cushion shield LH.
w/ Leg Support Adjustment Switch:
Detach the clamp and disconnect the 4 connectors to remove the front seat cushion shield LH.
| *A | w/o Leg Support Adjustment Switch |
| *B | w/ Leg Support Adjustment Switch |
| 6. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD LH |
![]() |
Remove the 2 screws.
Detach the guide in the direction indicated by the arrow shown in the illustration to remove the front inner No. 1 seat cushion shield LH.
| 7. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
![]() |
w/ Seat Heater System:
Disconnect the connector.
Detach the wire harness clamp to disconnect the wire harness of the front seatback heater assembly LH.
![]() |
Disconnect the connector.
Detach the wire harness clamp to disconnect the wire harness of the front seatback wire LH.
![]() |
Detach the connector clamp and 3 wire harness clamps to disconnect the wire harness of the front seat airbag assembly LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
Remove the 4 bolts and separate type front seatback assembly.
| 8. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Detach the hook.
![]() |
w/o Seat Heater System:
Pull out the 2 wire harnesses from the separate type front seatback cover.
w/ Seat Heater System:
Pull out the 3 wire harnesses from the separate type front seatback cover.
| *A | w/ Seat Heater System |
![]() |
Open the 2 fasteners.
![]() |
Detach the 2 hooks.
Remove the 4 clips.
Slide each hook to detach them.
Pull out the 4 straps of the separate type front seatback cover from the separate type front seatback pad.
![]() |
Detach the 6 fasteners.
| *1 | Fastener |
![]() |
Remove the 2 hog rings.
![]() |
Detach the 4 claws to remove the 2 front seat headrest supports.
Remove the separate type front seatback cover from the separate type front seatback pad.
| 9. REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
![]() |
w/ Climate Control Seat System:
Detach the 6 clips.
Remove the separate type front seatback pad from the front seatback frame sub-assembly LH.
| 10. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH |
![]() |
Detach the 2 clamps from the front seatback main frame sub-assembly.
Remove the 2 nuts and front seat airbag assembly LH.
| 11. REMOVE FRONT SEATBACK WIRE LH (for Driver Side) |
![]() |
w/o Climate Control Seat System:
Disconnect the 2 connectors.
Detach the 3 clamps to remove the front seatback wire LH.
![]() |
w/ Climate Control Seat System:
Disconnect the 3 connectors.
Detach the 5 clamps to remove the front seatback wire LH.
| 12. REMOVE FRONT SEATBACK WIRE RH (for Front Passenger Side) |
![]() |
Disconnect the 3 connectors.
Detach the 4 clamps to remove the front seatback wire RH.
| 13. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
![]() |
Spread the wires of the lumbar support adjuster assembly LH in the direction indicated by the arrow shown in the illustration to detach the 2 claws.
![]() |
Detach the 2 hooks.
![]() |
Remove the seatback climate control blower LH in the direction indicated by the arrow shown in the illustration.
| 14. REMOVE FRONT SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Detach the 2 clips and 2 guides to remove the lumbar support adjuster assembly LH from the front seatback frame sub-assembly LH.
| 15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
![]() |
Disconnect the connector.
Detach the connector clamp and 2 wire harness clamps to disconnect the seat cushion wire LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
for Driver Side:
Detach the 11 hooks.

![]() |
w/ Leg Support Adjustment Switch:
Detach the 4 hooks.
![]() |
w/ Leg Support Adjustment Switch:
Remove the 4 hog rings.
Remove the separate type front seat cushion cover with pad from the front seat cushion frame sub-assembly LH.
for Front Passenger Side:
Detach the 12 hooks.
Remove the separate type front seat cushion cover with pad from the front seat cushion frame sub-assembly RH.

| 16. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the connector.
Detach the claw and remove the occupant classification ECU from the front seat assembly RH.
| 17. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Disconnect the connector.
Detach the clamp to remove the seat heater control sub-assembly LH.
| 18. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System) |
![]() |
Detach the 2 clips.
![]() |
Detach the 2 claws and remove the seat cushion climate control duct LH.
| 19. REMOVE SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
![]() |
Detach the clamp.
Remove the 3 nuts and seat climate control blower LH.
| 20. REMOVE FRONT SEAT CUSHION WIRE LH (for Driver Side) |
![]() |
Disconnect the connector and detach the 2 claws.
![]() |
Disconnect the 2 connectors.
for 8 Way Seat Type:
![]() |
w/o Seat Heater System:
Disconnect the connector and detach the connector clamp and 3 wire harness clamps to remove the front seat cushion wire LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
w/ Seat Heater System:
Disconnect the connector and detach the 2 connector clamps and 3 wire harness clamps to remove the front seat cushion wire LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
for 10 Way Seat Type:
Disconnect the 2 connectors and detach the 2 connector clamps and 4 wire harness clamps to remove the front seat cushion wire LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
| 21. REMOVE FRONT SEAT CUSHION WIRE RH (for Front Passenger Side) |
![]() |
Disconnect the 4 connectors and detach the 2 connector clamps and 6 wire harness clamps to remove the front seat cushion wire RH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
| 22. REMOVE FRONT SEAT CUSHION PANEL SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and front seat cushion panel sub-assembly.
| *A | w/o Leg Support Adjustment Switch |
| *B | w/ Leg Support Adjustment Switch |
| 23. REMOVE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH |
![]() |
Detach the hook of the front side.
![]() |
Detach the 4 hooks of the rear side to remove the separate type front seat cushion spring assembly from the front seat cushion frame sub-assembly LH.
| 24. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH (for Driver Side) |
![]() |
Detach the hook.
![]() |
Remove the screw.
Detach the claw to remove the front lower seat cushion shield LH.
| 25. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH (for Driver Side) |
| 26. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH (for Front Passenger Side) |
![]() |
Detach the 2 claws to remove the front lower seat cushion shield LH.
| 27. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH (for Front Passenger Side) |
| 28. REMOVE UPPER SEAT TRACK COVER |
![]() |
Detach the 2 claws to remove the upper seat track cover.
| 29. REMOVE UPPER NO. 4 SEAT TRACK COVER |
![]() |
Detach the 2 claws to remove the upper No. 4 seat track cover.
| 30. REMOVE UPPER NO. 3 SEAT TRACK COVER |