LUMBAR SUPPORT ADJUSTER ASSEMBLY > INSTALLATION |
| 1. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
![]() |
Install the seatback climate control blower LH in the direction indicated by the arrow shown in the illustration.
![]() |
Attach the 2 hooks.
![]() |
Spread the wires of the lumbar support assembly LH in the direction indicated by the arrow shown in the illustration to attach the 2 claws.
| 2. INSTALL FRONT SEATBACK HOOK |
Install the 2 front seatback hooks to the lumbar support adjuster assembly LH.
| 3. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH |
Attach the 2 guides and 2 clips to install the lumbar support adjuster assembly LH.
| 4. INSTALL FRONT SEATBACK WIRE LH (for Driver Side) |
![]() |
w/o Climate Control Seat System:
Attach the 3 clamps to install the front seatback wire LH.
Connect the 2 connectors.
![]() |
w/ Climate Control Seat System:
Attach the 5 clamps to install the front seatback wire LH.
Connect the 3 connectors.
| 5. INSTALL FRONT SEATBACK WIRE RH (for Front Passenger Side) |
![]() |
Attach the 4 clamps to install the front seatback wire RH.
Connect the 3 connectors.
| 6. INSTALL SEPARATE TYPE FRONT SEATBACK PAD |
Install the separate type front seatback pad to the front seatback frame sub-assembly LH.
w/ Climate Control Seat System:
Attach the 6 clips.
| 7. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
Set the separate type front seatback cover in place.
Attach the 4 claws to install the 2 front seat headrest supports.
![]() |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.
| *1 | Hog Ring Pliers |
| *a | Cutout |
![]() |
Attach the 6 fasteners.
| *1 | Fastener |
Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.
Attach the 2 hooks.
Slide each hook to attach them.
Install the 4 clips.
![]() |
Close the 2 fasteners.
![]() |
w/o Seat Heater System:
Pass the 2 wire harnesses through the separate type front seatback cover.
w/ Seat Heater System:
Pass the 3 wire harnesses through the separate type front seatback cover.
| *A | w/ Seat Heater System |
Detach the hook.
| 8. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
When reusing a bolt:
Clean the threads of the bolt with non-residue solvent.
Apply adhesive to the threads of the bolt.
![]() |
Install the separate type front seatback assembly with the 4 bolts.
![]() |
Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.
| *1 | Connector Clamp |
| *2 | Wire Harness Clamp |
![]() |
Attach the wire harness clamp to connect the wire harness of the front seatback wire LH.
Connect the connector.
![]() |
w/ Seat Heater System:
Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly LH.
Connect the connector.
| 9. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH |
![]() |
Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.
Install the 2 screws.
| 10. INSTALL FRONT SEAT CUSHION SHIELD LH |
![]() |
w/o Leg Support Adjustment Switch:
Connect the 2 connectors and attach the clamp to install the front seat cushion shield LH.
w/ Leg Support Adjustment Switch:
Connect the 4 connectors and attach the clamp to install the front seat cushion shield LH.
| *A | w/o Leg Support Adjustment Switch |
| *B | w/ Leg Support Adjustment Switch |
![]() |
Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration.
Install the 2 screws.
Connect the 2 rubber bands.
| 11. INSTALL FRONT SEAT ASSEMBLY LH |