Home › BODY › SEAT › FRONT SEATBACK HEATER (for Power Seat)

FRONT SEATBACK HEATER (for Power Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
  1. Set the front seatback heater assembly LH on the separate type front seatback cover.



    B354912
  1. Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 8 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
  1. Set the separate type front seatback cover in place.

  1. Attach the 4 claws to install the 2 front seat headrest supports.



    B354909E01
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *a
    Cutout



    B354911E01
  1. Attach the 6 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.

  1. Attach the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after attaching the 2 hooks.
    3. Attach the 2 hooks securely.


    1. Slide each hook to attach them.

    2. Install the 4 clips.



    B356804
  1. Close the 2 fasteners.



    B354905E01
  1. w/o Seat Heater System:

    1. Pass the 2 wire harnesses through the separate type front seatback cover.

  1. w/ Seat Heater System:

    1. Pass the 3 wire harnesses through the separate type front seatback cover.
      Text in Illustration 
      *A
      w/ Seat Heater System

  1. Detach the hook.



3. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. When reusing a bolt:

    1. Clean the threads of the bolt with non-residue solvent.

    2. Apply adhesive to the threads of the bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



    B354903
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    B354902E01
  1. Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp



    B354901
  1. Attach the wire harness clamp to connect the wire harness of the front seatback wire LH.

  1. Connect the connector.



    B354900
  1. w/ Seat Heater System:

    1. Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly LH.

    2. Connect the connector.



4. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354899
  1. Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



5. INSTALL FRONT SEAT CUSHION SHIELD LH


    B354890E01
  1. w/o Leg Support Adjustment Switch:

    1. Connect the 2 connectors and attach the clamp to install the front seat cushion shield LH.

  1. w/ Leg Support Adjustment Switch:

    1. Connect the 4 connectors and attach the clamp to install the front seat cushion shield LH.
      Text in Illustration 
      *A
      w/o Leg Support Adjustment Switch
      *B
      w/ Leg Support Adjustment Switch



    B354889E01
  1. Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the 2 rubber bands.



6. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)