Home › BODY › SEAT › FRONT SEAT CUSHION HEATER (for Power Seat)

FRONT SEAT CUSHION HEATER (for Power Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
  1. Set the front seat cushion heater assembly LH on the separate type front seat cushion cover.



    B354928
  1. Using a tacker, install the front seat cushion heater assembly LH to the separate type front seat cushion cover with 10 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
  1. Set the separate type front seat cushion cover in place.



    B354927E01
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 10 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

  1. Attach the 2 fasteners.
    Text in Illustration 
    *1
    Fastener
    *2
    Hog Ring Pliers
    *a
    Cutout



3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
  1. Set the separate type front seat cushion cover with pad on the front seat cushion frame sub-assembly LH.



  1. for Driver Side:



      B354923E01
    1. w/ Leg Support Adjustment Switch:
      Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with 4 new hog rings as shown in the illustration.

      NOTICE:
      1. Be careful not to damage the separate type front seat cushion cover.
      2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      HINT:
      Install the hog rings at the cutouts if they are there.

      Text in Illustration 
      *1
      Hog Ring Pliers
      *a
      Cutout

    2. w/ Leg Support Adjustment Switch:
      Attach the 4 hooks.



    3. Attach the 11 hooks to install the separate type front seat cushion cover with pad.


      B354920



  1. for Front Passenger Side:



    1. Attach the 12 hooks to install the separate type front seat cushion cover with pad.


      B354924



    B354925E01
  1. Attach the connector clamp and 2 wire harness clamps to connect the seat cushion wire LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp

  1. Connect the connector.



4. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. When reusing a bolt:

    1. Clean the threads of the bolt with non-residue solvent.

    2. Apply adhesive to the threads of the bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



    B354903
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    B354902E01
  1. Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp



    B354901
  1. Attach the wire harness clamp to connect the wire harness of the front seatback wire LH.

  1. Connect the connector.



    B354900
  1. w/ Seat Heater System:

    1. Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly LH.

    2. Connect the connector.



5. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354899
  1. Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



6. INSTALL FRONT SEAT CUSHION SHIELD LH


    B354890E01
  1. w/o Leg Support Adjustment Switch:

    1. Connect the 2 connectors and attach the clamp to install the front seat cushion shield LH.

  1. w/ Leg Support Adjustment Switch:

    1. Connect the 4 connectors and attach the clamp to install the front seat cushion shield LH.
      Text in Illustration 
      *A
      w/o Leg Support Adjustment Switch
      *B
      w/ Leg Support Adjustment Switch



    B354889E01
  1. Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the 2 rubber bands.



7. INSTALL FRONT SEAT ASSEMBLY
(Click here)