Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD DEICER SYSTEM

WINDSHIELD DEICER SYSTEM > Windshield Deicer does not Operate

for Preparation Click here


DESCRIPTION

When the air conditioning control assembly (windshield deicer switch) turns is turned on, a windshield deicer activation request signal is sent via the LIN communication line to the air conditioning amplifier. Then the air conditioning amplifier operates the windshield deicer.

WIRING DIAGRAM


B356784E01


INSPECTION PROCEDURE

HINT:
This circuit uses the LIN communication line. Before performing the inspection, check that the LIN communication system is functioning normally (Click here).

1.PERFORM ACTIVE TEST USING TECHSTREAM (WINDSHIELD DEICER RELAY ASSEMBLY)
  1. Select the Active Test using the Techstream to generate a control command, and then check that the windshield deicer operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Deicer Relay (Front)
    Windshield deicer relay assembly
    ON or OFF
    -

    OK:
    Windshield deicer relay assembly turns ON and OFF.



NG
Go to step 3
OK


2.CHECK AIR CONDITIONING CONTROL ASSEMBLY
  1. Temporarily replace the air conditioning control assembly with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE) 

3.INSPECT FUSE (DEICER, LH-IG)
  1. Remove the DEICER fuse from the engine room relay block, junction block.

  1. Remove the LH-IG fuse from the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DEICER fuse
    Always
    Below 1 Ω
    LH-IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


4.INSPECT WINDSHIELD DEICER RELAY ASSEMBLY (DEICER)
B356785E01
  1. Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE WINDSHIELD DEICER RELAY ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIR CONDITIONING AMPLIFIER AND BATTERY)
B160785E04
  1. Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.

  1. Disconnect the J19 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Windshield deicer relay assembly (DEICER) terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    Windshield deicer relay assembly (DEICER) terminal 3 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Windshield deicer relay assembly (DEICER) terminal 2 - J19-40 (D)
    Always
    Below 1 Ω
    Windshield deicer relay assembly (DEICER) terminal 2 or J19-40 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (DEICER RELAY - WINDSHIELD DEICER WIRE)
B160786E04
  1. Remove the windshield deicer relay assembly (DEICER) from the engine room relay block, junction block.

  1. Disconnect the A23 windshield glass (windshield deicer wire) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Windshield deicer relay assembly (DEICER) terminal 5 - A23-1 (B)
    Always
    Below 1 Ω
    Windshield deicer relay assembly (DEICER) terminal 5 or A23-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER WIRE - BODY GROUND)
B160784E01
  1. Disconnect the A23 windshield glass (windshield deicer wire) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A23-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (WINDSHIELD DEICER POWER SOURCE)
B160784E02
  1. Disconnect the A23 windshield glass (windshield deicer wire) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A23-1 (B) - A23-2 (E)
    Ignition switch ON, windshield deicer switch on
    11 to 14 V
    Ignition switch ON, windshield deicer switch off
    Below 1 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK

REPLACE WINDSHIELD GLASS (Click here)