Home › ENGINE ยท 1UR-FE › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL THROTTLE BODY ASSEMBLY


    A218983E03
  1. Align the protrusion of a new gasket with the groove of the intake manifold, and install the gasket.
    Text in Illustration 
    *1
    Gasket
    *a
    Groove
    *b
    Protrusion

  1. Install the throttle body assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR


    A215299
  1. Install a new O-ring to the manifold absolute pressure sensor.



    A215298
  1. Install the manifold absolute pressure sensor with the screw.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the manifold absolute pressure sensor connector.



3. INSTALL UNION TO CONNECTOR TUBE HOSE ASSEMBLY
  1. Install the 2 wire harness brackets with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the union to connector tube hose assembly with the 2 bolts.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the union to connector tube hose to the intake manifold, and slide the clamp to secure the hose.



4. INSTALL PURGE VSV
  1. Install the purge VSV with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the purge line hose to the intake manifold, and slide the clamp to secure the hose.



5. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)
  1. Install the vacuum switching valve assembly with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 vacuum hoses to the vacuum switching valve assembly.



6. INSTALL STUD BOLT
  1. Using an E5 "TORX" socket wrench, install the 2 stud bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL V-BANK COVER BOLT
  1. Install the V-bank cover bolt to the intake manifold.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL V-BANK COVER BRACKET
  1. Install the V-bank cover bracket with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL FUEL TUBE SUB-ASSEMBLY
  1. Install the fuel tube sub-assembly to the intake manifold with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



10. INSTALL INTAKE MANIFOLD


    A215297
  1. Place 2 new gaskets on the intake manifold.

  1. Place the intake manifold on the cylinder head sub-assembly.

  1. Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly LH (Click here).

  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly RH (Click here).

  1. Attach the 4 clamps to the fuel tube sub-assembly.

  1. Attach the 3 engine wire harness clamps to the 3 wire harness brackets.

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the vacuum hose to the union to connector tube hose assembly, and slide the clamp to secure the hose.

  1. Connect the purge line hose to the purge VSV, and slide the clamp to secure the hose.

  1. Connect the 2 vacuum switching valve connectors.

  1. Connect the ventilation hose to the intake manifold, and slide the clamp to secure the hose.

  1. Connect the No. 4 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.

  1. Connect the throttle body connector to the throttle body assembly.



11. INSTALL VENTILATION HOSE ASSEMBLY
  1. Install the ventilation hose assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the ventilation hose assembly to the ventilation pipe of the cylinder head cover sub-assembly LH and cylinder head cover sub-assembly RH, and slide the 2 clamps to secure the hose.



12. INSTALL AIR TUBE SUB-ASSEMBLY LH


    A215284
  1. Connect the air hose to the air switching valve LH, and install the air tube LH with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the vacuum sensor connector and clamp.



    A217630E01
  1. Connect the air tube LH to the water inlet housing with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the air hose.

  1. Connect the 2 wire harness clamps.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



    A215880E01
  1. Connect the water by-pass hose and 2 connectors.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



13. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Install the cowl top outer panel sub-assembly with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the washer hose and attach the 2 wire harness clamps.



14. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


15. INSTALL EGR VALVE ASSEMBLY
(Click here)


16. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.