Home › ENGINE ยท 1UR-FE › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



2. REMOVE EGR VALVE ASSEMBLY
(Click here)


3. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


4. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose and detach the 2 wire harness clamps.



  1. Remove the 7 bolts and cowl top outer panel sub-assembly.


    A215877



5. REMOVE VENTILATION HOSE ASSEMBLY


    A215286
  1. Slide the 2 clamps and disconnect the ventilation hose assembly from the ventilation pipe of the cylinder head cover sub-assembly LH and cylinder head cover sub-assembly RH.

  1. Remove the bolt and ventilation hose assembly.



6. REMOVE AIR TUBE SUB-ASSEMBLY LH


    A215879
  1. Disconnect the 2 connectors.

  1. Disconnect the water by-pass hose.



    A215282
  1. Disconnect the 2 wire harness clamps and air hose.

  1. Remove the bolt and disconnect the air tube LH from the water inlet housing.



    A215284
  1. Disconnect the vacuum sensor connector and clamp.

  1. Remove the 2 bolts and disconnect the air hose from the air switching valve LH.

  1. Remove the air tube LH.



7. REMOVE INTAKE MANIFOLD


    A307762
  1. Disconnect the throttle body connector from the throttle body assembly.

  1. Slide the clamp and disconnect the No. 4 water by-pass hose from the front water by-pass joint.

  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A215287
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A215288
  1. Slide the clamp and disconnect the vacuum hose from the union to connector tube hose assembly.



    A215285
  1. Remove the bolt.

  1. Detach the 3 engine wire harness clamps from the 3 wire harness brackets.



    A307793
  1. Detach the 4 clamps from the fuel tube sub-assembly.



    A214311
  1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly RH (Click here).



    A214312
  1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly LH (Click here).



    A215289
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



8. REMOVE FUEL TUBE SUB-ASSEMBLY


    A215303
  1. Remove the bolt and fuel tube sub-assembly from the intake manifold.



9. REMOVE V-BANK COVER BRACKET


    A215290
  1. Remove the 2 bolts and V-bank cover bracket.



10. REMOVE V-BANK COVER BOLT


    A215291
  1. Remove the V-bank cover bolt from the intake manifold.



11. REMOVE STUD BOLT


    A216133
  1. Using an E5 "TORX" socket wrench, remove the 2 stud bolts.



12. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Disconnect the 2 vacuum hoses from the vacuum switching valve assembly.

  1. Remove the bolt and vacuum switching valve assembly.



13. REMOVE PURGE VSV


    A215294
  1. Slide the clamp and disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



14. REMOVE UNION TO CONNECTOR TUBE HOSE ASSEMBLY


    A215295
  1. Slide the clamp and disconnect the union to connector tube hose from the intake manifold.

  1. Remove the 2 bolts and union to connector tube hose assembly.

  1. Remove the 2 bolts and 2 wire harness brackets.



15. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Disconnect the manifold absolute pressure sensor connector.



    A215298
  1. Remove the screw and manifold absolute pressure sensor.



    A215299
  1. Remove the O-ring from the manifold absolute pressure sensor.



16. REMOVE THROTTLE BODY ASSEMBLY


    A215292
  1. Remove the 4 bolts, throttle body assembly and gasket.