Home › ENGINE · 3UR-FE › EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151835E01

  1. Tighten the radiator drain cock plug by hand.



5. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E04
  1. Raise the front of the V-bank cover sub-assembly to detach the 2 pins. Then remove the 2 V-bank cover hooks from the No. 1 V-bank cover bracket, and remove the V-bank cover sub-assembly.
    Text in Illustration 
    *1
    V-bank Cover Grommet
    *2
    Pin
    *3
    No. 1 V-bank Cover Bracket
    *4
    V-bank Cover Hook



6. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



7. REMOVE AIR CLEANER ASSEMBLY


    A309637E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. for Type A:
      Unfasten the 4 hook clamps and then remove the air cleaner cap.

    4. for Type B:
      Unfasten the 2 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A309638E01
  1. Remove the 2 bolts and air cleaner case.



8. DISCONNECT INLET RADIATOR HOSE


9. DISCONNECT OUTLET RADIATOR HOSE


10. REMOVE FAN AND GENERATOR V-BELT


    A163770E01
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



11. REMOVE FAN SHROUD


    A151842
  1. Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V-belt.

  1. Disconnect the reservoir hose from the upper radiator tank.



    A215579
  1. for Condenser with Integrated Oil Cooler:
    Detach the claw and open the No. 1 flexible hose clamp.



    A151821
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fan with fluid coupling, and then remove the fan shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



12. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and fender apron seal.



13. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and fender apron seal.



14. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and fender apron seal.



15. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



16. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



17. DISCONNECT VANE PUMP ASSEMBLY


    A164433
  1. Detach the 2 clamps and disconnect the power steering oil pressure switch connector.



    A163289
  1. Remove the 2 bolts and disconnect the vane pump.



18. REMOVE GENERATOR ASSEMBLY


    A163292
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.



    A163290
  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A260951
  1. Remove the 3 bolts, nut and generator.



19. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



20. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
(Click here)


21. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


22. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C155150E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft from the steering intermediate shaft.



    C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and the power steering gear.

  1. Remove the bolt and disconnect the No. 2 steering intermediate shaft from the power steering gear.



23. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Remove the 3 bolts and heat insulator.



24. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A162115
  1. Remove the 10 nuts, exhaust manifold and 2 gaskets.



25. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Remove the 3 bolts and heat insulator.



26. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162754
  1. Remove the 10 nuts, exhaust manifold and 2 gaskets.