DTC B2650 Slide Sensor Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B2650 | The forward and rearward lock detection position of the sensor is the same. |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (SEAT SLIDE OPERATION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Seat Slide Operation | Seat sliding operation | Front / OFF / Rear | - |
|
| ||||
| OK | |
| 2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT) |
![]() |
Disconnect the front seat cushion frame sub-assembly LH (slide motor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Z3-5 - Z3-6 | Sliding switch on | 4.8 to 5.1 V |
| *a | Front view of wire harness connector (to Front Seat Cushion Frame Sub-assembly LH [Slide Motor]) |
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR) |
![]() |
Reconnect the front seat cushion frame sub-assembly LH (slide motor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Z3-5 - Body ground | Sliding switch on | 4.5 to 4.8 V |
| *a | Component with harness connected (Front Seat Cushion Frame Sub-assembly LH [Slide Motor]) |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH) |
Disconnect the Z10 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Z10-5 (SSRS) - Z3-5 | Always | Below 1 Ω |
| Z10-1 (SGND) - Z3-6 | Always | Below 1 Ω |
| Z10-5 (SSRS) or Z3-5 - Body ground | Always | 10 kΩ or higher |
| Z10-1 (SGND) or Z3-6 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE MOTOR) |
Remove the front seat cushion frame sub-assembly LH (slide Motor) (Click here).
Inspect the front seat cushion frame sub-assembly LH (slide motor) .
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH) |
Disconnect the Z9 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Z9-3 (SLD+) - Z3-4 | Always | Below 1 Ω |
| Z9-4 (SLD-) - Z3-3 | Always | Below 1 Ω |
| Z9-3 (SLD+) or Z3-4 - Body ground | Always | 10 kΩ or higher |
| Z9-4 (SLD-) or Z3-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||