Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2658    Short in Sensor with Motor Power Supply Circuit

for Preparation Click here


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code
DTC Detection Condition
Trouble Area
B2658
A problem with the voltage supplied to the position control sensor.
  1. Position control ECU and switch assembly
  2. Front seat cushion frame sub-assembly LH
  3. Front seatback frame sub-assembly LH
  4. Harness or connector

WIRING DIAGRAM


B352950E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z10 position control ECU and switch assembly connector.

  1. Disconnect the Z3 front seat cushion frame sub-assembly LH (slide motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-5 (SSRS) - Z3-5
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z3-6
    Always
    Below 1 Ω
    Z10-5 (SSRS) - Z10-1 (SGND)
    Always
    10 kΩ or higher
    Z10-5 (SSRS) or Z3-5 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z3-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)


    B245520E30
  1. Reconnect the Z10 position control ECU and switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z3-5 - Z3-6
    Sliding switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seat Cushion Frame Sub-assembly LH [Slide Motor])



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z10 position control ECU and switch assembly connector.

  1. Disconnect the Z4 front seat cushion frame sub-assembly LH (lifter motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-4 (SSRL) - Z4-4
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z4-3
    Always
    Below 1 Ω
    Z10-4 (SSRL) - Z10-1 (SGND)
    Always
    10 kΩ or higher
    Z10-4 (SSRL) or Z4-4 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z4-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)


    B352958E02
  1. Reconnect the Z10 position control ECU and switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z4-4 - Z4-3
    Lifter switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seat Cushion Frame Sub-assembly LH [Lifter Motor])



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z10 position control ECU and switch assembly connector.

  1. Disconnect the Z14 front seat cushion frame sub-assembly LH (vertical motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-3 (SSFV) - Z14-2
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z14-1
    Always
    Below 1 Ω
    Z10-3 (SSFV) - Z10-1 (SGND)
    Always
    10 kΩ or higher
    Z10-3 (SSFV) or Z14-2 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z14-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (VERTICAL MOTOR CIRCUIT)


    B352962E01
  1. Reconnect the Z10 position control ECU and switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z14-2 - Z14-1
    Front vertical switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seat Cushion Frame Sub-assembly LH [Vertical Motor])



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


8.CHECK FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Temporarily replace the front seat cushion frame sub-assembly LH with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 9
OK

END (FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH WAS DEFECTIVE) 

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z10 position control ECU and switch assembly connector.

  1. Disconnect the Z6 front seatback frame sub-assembly LH (reclining motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-11 (SSRR) - Z6-4
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z6-3
    Always
    Below 1 Ω
    Z10-11 (SSRR) - Z10-1 (SGND)
    Always
    10 kΩ or higher
    Z10-11 (SSRR) or Z6-4 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z6-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)


    B352958E03
  1. Reconnect the Z10 position control ECU and switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z6-4 - Z6-3
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seatback Frame Sub-assembly LH [Reclining Motor])



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


11.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH
  1. Temporarily replace the front seatback frame sub-assembly LH (reclining motor) with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK

END (FRONT SEATBACK FRAME SUB-ASSEMBLY LH WAS DEFECTIVE)