Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



BRIEF DESCRIPTION
  1. The CAN (Controller Area Network) is a serial data communication system for real-time application. It is a vehicle multiplex communication system which has a high communication speed (500 kbps) and the ability to detection malfunctions.

  2. By pairing the CANH and CANL bus lines, the CAN performs communication based on differential voltages.

  3. Many ECUs (sensors) installed on the vehicle operate by sharing information and communication with each other.

  4. The CAN has 2 resistors of 120 Ω which are necessary to communicate using the main wire.


DEFINITION OF TERMS
  1. CAN main wire

    1. The CAN main wire is a wire harness between the 2 termination circuits on the bus (communication line). This is the CAN main bus in the CAN communication system.

  2. CAN branch wire

    1. The CAN branch wire is a wire harness which diverges from the main wire to an ECU or sensor.

  3. Termination circuit

    1. The termination circuit is a circuit which converts the communication current of the CAN communication into the bus voltage. It consists of a resistor and capacitor. 2 termination circuits are necessary on a bus.

  4. CAN junction connector

    1. The CAN junction connector is designed so that it can be used with CAN communication which has a termination circuit and CAN communication which does not have a termination circuit.


CIRCUIT DESCRIPTION
  1. The V bus, V2 bus, MS bus and sensor bus each have termination circuits with resistance of 120 Ω x 2. High speed communication at 250 kbps and 500 kbps is possible.


ECUS OR SENSORS WHICH COMMUNICATE VIA CAN COMMUNICATION SYSTEM
  1. ECM

  2. Brake actuator assembly (skid control ECU)

  3. Combination meter assembly

  4. Center airbag sensor assembly

  5. Air conditioning amplifier assembly

  6. Steering angle sensor

  7. Main body ECU (driver side junction block assembly)

  8. DLC3

  9. Bus buffer ECU*1

  10. 4WD control ECU*2

  11. Network gateway ECU*3

  12. Radio and display receiver assembly*4

  13. Navigation receiver assembly*5

  14. Blind spot monitor sensor RH*3

  15. Blind spot monitor sensor LH*3

  16. Front power seat ECU and switch LH*6

  17. Outer mirror control ECU assembly*6

  18. Multiplex tilt and telescopic ECU*6

    1. *1: w/ Bus Buffer ECU
    2. *2: for 4WD
    3. *3: w/ Blind Spot Monitor System
    4. *4: w/ Audio and Visual System
    5. *5: w/ Navigation System
    6. *6: w/ Seat Memory


DIAGNOSTIC CODES FOR CAN COMMUNICATION SYSTEM
  1. DTCs for the CAN communication system are as follows: U0073, U0100, U0114, U0122, U0123, U0126, U0129, U0140, U0155, U0164, U0199, U0208, U0232, U0233, U0416, U1002, U1115, B1499, B2621 and B2624.


NOTES REGARDING TROUBLESHOOTING
  1. Trouble in the CAN bus (communication line) can be checked through the DLC3 (except when there is a wire break in the CAN branch wire of the DLC3).

  2. DTCs regarding the CAN communication system can be checked using the Techstream.

  3. The CAN communication system cannot detect trouble in the CAN branch wire of the DLC3 even though the DLC3 is also connected to the CAN communication system.


HOW TO DISTINGUISH CAN JUNCTION CONNECTOR CONNECTORS
  1. In the CAN communication system, the shape of all connectors connected to the CAN junction connector is the same.
    The connectors connected to the CAN junction connector can be distinguished by the colors of the bus line and the connecting side of the connector.

    HINT:
    See "Terminals of ECU" (Click here) for bus line color or the type of connecting surface.