Home › ENGINE ยท 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P219A    Bank 1 Air-Fuel Ratio Imbalance

DTC    P219B    Bank 2 Air-Fuel Ratio Imbalance

DTC    P219C    Cylinder 1 Air-Fuel Ratio Imbalance

DTC    P219D    Cylinder 2 Air-Fuel Ratio Imbalance

DTC    P219E    Cylinder 3 Air-Fuel Ratio Imbalance

DTC    P219F    Cylinder 4 Air-Fuel Ratio Imbalance

DTC    P21A0    Cylinder 5 Air-Fuel Ratio Imbalance

DTC    P21A1    Cylinder 6 Air-Fuel Ratio Imbalance

DTC    P21A2    Cylinder 7 Air-Fuel Ratio Imbalance

DTC    P21A3    Cylinder 8 Air-Fuel Ratio Imbalance

for Preparation Click here


DESCRIPTION

Refer to DTC P0300 .
Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P219A
The difference in air-fuel ratios between the cylinders exceeds the threshold.
  1. Fuel injector assembly
  2. Air induction system
  3. Gas leak from exhaust system
  4. Ignition system
  5. Compression pressure
  6. Air fuel ratio sensor
  7. ECM
P219B
The difference in air-fuel ratios between the cylinders exceeds the threshold.
P219C
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219D
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219E
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P219F
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A0
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A1
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A2
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
P21A3
The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).

MONITOR DESCRIPTION

  1. Fuel System Air-fuel Ratio Cylinder Imbalance Monitor
    The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air-fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leakage in the intake or exhaust system, etc.
    When the air-fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.
  1. Air Fuel Ratio Sensor Monitoring Method: P219A and/or P219B are stored primarily when a rich side imbalance is detected.
    When the system detects a difference in air-fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.
  1. Crankshaft Position Sensor Monitoring Method: P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are stored primarily when a lean side imbalance is detected.
    The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air-fuel ratios between the cylinders, which it determines to be a problem.

MONITOR STRATEGY


Related DTCs
P219A: Air fuel ratio cylinder imbalance monitor (Bank 1)
P219B: Air fuel ratio cylinder imbalance monitor (Bank 2)
P219C: Air fuel ratio cylinder imbalance monitor (Cylinder 1)
P219D: Air fuel ratio cylinder imbalance monitor (Cylinder 2)
P219E: Air fuel ratio cylinder imbalance monitor (Cylinder 3)
P219F: Air fuel ratio cylinder imbalance monitor (Cylinder 4)
P21A0: Air fuel ratio cylinder imbalance monitor (Cylinder 5)
P21A1: Air fuel ratio cylinder imbalance monitor (Cylinder 6)
P21A2: Air fuel ratio cylinder imbalance monitor (Cylinder 7)
P21A3: Air fuel ratio cylinder imbalance monitor (Cylinder 8)
Required Sensors/Components (Main)
Air fuel ratio sensor
Crankshaft position sensor
Required Sensors/Components (Related)
Mass air flow meter assembly
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds: Air fuel ratio sensor open circuit between AF+ and AF- and low impedance
30 seconds: Crankshaft position sensor monitoring method
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not stored
P0010, P0020 (Camshaft timing oil control valve assembly bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust camshaft timing oil control valve assembly bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P1340 (Camshaft position sensor)
P2440 - P2447 (Secondary air injection system)
P0500 (Vehicle speed sensor)

P219A, P219B: Air Fuel Ratio Sensor Monitoring Method 
Air fuel ratio sensor status
Activated
Engine speed
1400 to 2200 rpm
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa (570 mmHg) or higher
Fuel system status
Closed loop

P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3: Crankshaft Position Sensor Monitoring Method 
Vehicle speed
Less than 3 km/h (1.875 mph)
Engine speed
400 to 1050 rpm
Engine coolant temperature
75°C (167°F) or higher
Air fuel ratio sensor status
Activated
Battery voltage
11 V or higher
Fuel system status
Closed loop

TYPICAL MALFUNCTION THRESHOLDS


P219A: Air Fuel Ratio Sensor Monitoring Method (Bank 1) 
A/F sensor monitoring method criteria
0.11 or more

P219B: Air Fuel Ratio Sensor Monitoring Method (Bank 2) 
A/F sensor monitoring method criteria
0.1 or more

P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3: Crankshaft Position Sensor Monitoring Method 
Crankshaft position sensor monitoring method criteria (lean side imbalance)
1.0 or more

MONITOR RESULT

Refer to detailed information in Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A240420E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N.

  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Drive the vehicle at 60 km/h (38 mph) or higher for 2 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    It is acceptable to turn electrical loads on while driving.

  7. Idle the engine for 2 minutes or more [C].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [E].
  11. Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.

    HINT:
    Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).

  12. Drive the vehicle at 60 km/h (38 mph) or higher for 5 seconds or more [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  13. Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [G].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).

  15. Drive the vehicle at 60 km/h (38 mph) or more for 5 seconds or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  16. Repeat steps [G] through [H] above at least 2 times [I].
  17. Idle the engine for 1 minute or more [J].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N.

  18. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
  19. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  20. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  21. Input the DTC: P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3.
  22. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  23. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    1. *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.

1.CHECK FOR ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output
    A
    DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 and other DTCs are output
    B

    HINT:
    If any DTCs other than DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Freeze Frame Data Items for DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3
    1. Vehicle Speed
    2. Engine Speed
    3. Calculate Load
    4. Accelerator Idle Position
    5. Short FT #1 or #2
    6. Long FT #1 or #2
    7. Cylinder #1 Misfire Count to Cylinder #8 Misfire Count

    HINT:
    When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.


    Air Fuel Ratio Sensor Monitoring Method (P219A and P219B)
    Crankshaft Position Sensor Monitoring Method (P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and P21A3)
    Note
    DTCs are output
    DTC is output (Only one DTC relating to a single cylinder is output)
    Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.
    DTCs are output
    DTCs are output (Multiple DTCs relating to multiple cylinders are output)
    Malfunction of cylinders except ones detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.*1
    DTCs are not output
    DTCs are output
    Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.
    DTCs are output
    DTCs are not output
    Malfunctioning of the bank detected by the Air Fuel Ratio Sensor Monitoring Method is primarily suspected.
    *1: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.


NEXT


3.READ VALUE USING DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    HINT:
    1. If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.
    2. Perform inspections while focusing on the cylinder whose misfire count has increased.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    Result 
    Result
    Proceed to
    DTC P219A or P219B is output
    A
    DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3 are output
    B
    DTC P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output



B
Go to step 6
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #8 Misfire Count.

    HINT:
    When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Air Induction System).

  1. Perform the Control the Injection Volume operation with the engine idling.

  1. Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count") while decreasing the injection volume in 5% increments.

    NOTICE:
    Do not decrease the injection volume by more than 20%.

    Result:
    The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.


NEXT


5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage (Click here).

    OK:
    No leakage in air induction system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the air induction system (Click here).



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the cylinder causing the imbalance (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test (Click here).

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly (Click here).


NEXT


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


11.CHECK FOR CAUSE OF FAILURE
  1. If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.

  1. Check the intake valve for deposits.

    HINT:
    As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head and check the intake valve.


NEXT


12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Check for DTCs.

    Result:
    P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 is not output.


NEXT

END