Regular Cab
With the cowl top side panel removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
*a: This part of the outer panel is reused, because the rocker panel section is cut off at the rear position behind the supplied parts cut position of the outer panel.
Remove the front pillar upper inner extension at the same time.
| *b | mm (in.) | - | - |
| *1 | Front Pillar Upper Inner Extension | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Spot Weld |
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Tack Weld |
|
Butt Weld |
|
Body Sealer |
Before temporarily installing the new parts, weld the rocker outer reinforce, front body pillar lower reinforce, front body upper inner pillar, cowl side panel, front pillar upper inner extension, front body pillar upper inner reinforcement, front body outer pillar and No. 6 pillar outer bracket with the standard number of welding points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
After welding, apply polyurethane foam to the corresponding parts. (See the painting / coating)
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *1 | Front Body Outer Pillar | *2 | Rocker Outer Reinforce |
| *3 | Front Body Pillar Lower Reinforce | *4 | Front Body Upper Inner Pillar |
| *5 | Front Body Pillar Upper Inner Reinforcement | *6 | Cowl Side Panel |
| *7 | Front Pillar Upper Inner Extension | - | - |
| *a | mm (in.) | - | - |
| *1 | Front Body Pillar Lower Reinforce | *2 | Front Body Upper Inner Pillar |
| *3 | Front Pillar Upper Inner Extension | *4 | Front Body Pillar Upper Inner Reinforcement |
| *5 | Cowl Side Panel | *6 | Rocker Outer Reinforce |
| *7 | Front Body Outer Pillar | *8 | No. 6 Pillar Outer Bracket |
| *a | mm (in.) | - | - |
Ex. Regular Cab
With the cowl top side panel removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
*a: This part of the outer panel is reused, because the rocker panel section is cut off at the rear position behind the supplied parts cut position of the outer panel.
Remove the front pillar upper inner extension at the same time.
| *b | mm (in.) | - | - |
| *1 | Front Pillar Upper Inner Extension | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Spot Weld |
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Tack Weld |
|
Butt Weld |
|
Body Sealer |
Before temporarily installing the new parts, weld the rocker outer reinforce, front body pillar lower reinforce, front body upper inner pillar, cowl side panel, front pillar upper inner extension, front body pillar upper inner reinforcement, front body outer pillar and No. 6 pillar outer bracket with the standard number of welding points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
After welding, apply polyurethane foam to the corresponding parts. (See the painting / coating)
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *A | Double Cab | *B | CrewMax |
| *C | LH | *D | RH |
| *1 | Front Body Outer Pillar | *2 | Rocker Outer Reinforce |
| *3 | Front Body Pillar Lower Reinforce | *4 | Front Body Upper Inner Pillar |
| *5 | Front Body Pillar Upper Inner Reinforcement | *6 | Cowl Side Panel |
| *7 | Front Pillar Upper Inner Extension | - | - |
| *a | mm (in.) | - | - |
| *1 | Front Body Pillar Lower Reinforce | *2 | Front Body Upper Inner Pillar |
| *3 | Front Pillar Upper Inner Extension | *4 | Front Body Pillar Upper Inner Reinforcement |
| *5 | Cowl Side Panel | *6 | Rocker Outer Reinforce |
| *7 | Front Body Outer Pillar | *8 | No. 6 Pillar Outer Bracket |
| *a | mm (in.) | - | - |