2016-2017 Tundra Service Manual
1UR-FE · 3UR-FBE · 3UR-FE
Trouble codes (1301)
- P0010Open or short in OCV (for intake side of bank 1) circuit (1 trip detection logic)
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0013Open or short in OCV (for exhaust side of bank 1) circuit (1 trip detection logic)
- P0014Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0015Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0016Deviation in crankshaft position sensor signal and VVT sensor (for Intake Side of Bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor (for Exhaust Side of Bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor (for Intake Side of Bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor (for Exhaust Side of Bank 2) signal (2 trip...
- P0020Open or short in OCV (for intake side of bank 2) circuit (1 trip detection logic)
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0023Open or short in OCV (for exhaust side of bank 2) circuit (1 trip detection logic)
- P0024Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0025Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic)
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0051Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic)
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P006AAfter the engine is warmed up and the engine is idled for 30 seconds or more, the intake manifold pressure...
- P0101Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic): (a) Engine...
- P0102Mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic: Engine speed is less than...
- P0103Mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic: Engine speed is less...
- P0107The manifold absolute pressure sensor voltage is below 0.5 V for 0.5 seconds. (1 trip detection logic)
- P0108The manifold absolute pressure sensor voltage is higher than 4.5 V for 0.5 seconds. (1 trip detection logic)
- P0111When either condition below is met: (2 trip detection logic) 1. The intake air temperature change from the...
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116When either of following conditions met (2 trip detection logic): · When cold engine started and engine...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P0120Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0121Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection...
- P0122Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0123Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0136Either condition is met: · Abnormal voltage output: During active air-fuel ratio control, HO2 sensor voltage...
- P0137Either condition is met: · Low voltage (open): During active air-fuel ratio control, following conditions (a)...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0139Heated oxygen sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection...
- P013AHeated oxygen sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip...
- P013CHeated oxygen sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip...
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P014CThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014DThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014EThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014FThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P0156Either condition is met: · Abnormal voltage output: During active air-fuel ratio control, HO2 sensor voltage...
- P0157Either condition is met: · Low voltage (open): During active air-fuel ratio control, following conditions (a)...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0159Heated oxygen sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection...
- P015AThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015CThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015DThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0222Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0223Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal...
- P0300Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip...
- P0301Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection...
- P0327Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P032COutput voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P032DOutput voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P0335Either condition is met: · No crankshaft position (CKP) sensor signal to ECM while cranking (1 trip detection...
- P0337Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
- P0338Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
- P0339Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection...
- P033COutput voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P033DOutput voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0340No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0342Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0343Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0345No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0347Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0348Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0355No IGF signal to ECM while engine running (1 trip detection logic)
- P0356No IGF signal to ECM while engine running (1 trip detection logic)
- P0357No IGF signal to ECM while engine running (1 trip detection logic)
- P0358No IGF signal to ECM while engine running (1 trip detection logic)
- P0365No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0367Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0368Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0390No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0392Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0393Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0401Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut...
- P0403Open or short in EGR valve circuit (1 trip detection logic)
- P0412After cold engine start, all of following conditions met (1 trip detection logic): 1. Secondary Air Injection...
- P0415After cold engine start, all of following conditions met (1 trip detection logic): 1. Secondary Air Injection...
- P0418After cold engine start, all of following conditions met (2 trip detection logic): 1. Secondary Air Injection...
- P0419After cold engine start, all of following conditions met (2 trip detection logic): 1. Secondary Air Injection...
- P0420OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P043E, P043F, P2401, P2402 and P2419 present when one of following conditions met during key-off EVAP...
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0451Sensor output voltage fluctuates frequently within certain time period.
- P0452EVAP pressure Below 42.1 kPa for 0.5 seconds.
- P0453EVAP pressure higher than 123.8 kPa for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic)
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON...
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2 trip detection logic)
- P0550Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine...
- P0552Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running. (1 trip...
- P0553Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running. (1 trip...
- P0560Open in ECM back up power source circuit (1 trip detection logic)
- P0604ECM RAM errors (1 trip detection logic)
- P0606When either condition below is met: · ECM main CPU error · ECM sub CPU error (1 trip detection logic)
- P0607Either condition is met: · ECM CPU malfunction · HO2S transistor malfunction (1 trip detection logic)
- P060AWhen any condition below is met: · ECM main CPU error · ECM sub CPU error · Electronic throttle monitoring...
- P060BECM main CPU communication error (1 trip detection logic)
- P060DWhen either condition below is met: · ECM main CPU error · ECM sub CPU error (1 trip detection logic)
- P060EWhen either condition below is met: · ECM main CPU error · ECM sub CPU error (1 trip detection logic)
- P0617When conditions (a), (b) and (c) met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20...
- P062FAn ECM internal error (EEPROM). (1 trip detection logic)
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0657Throttle actuator power supply error (1 trip detection logic)
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P106AThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P106BThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P144COpen or short in the air pump heater (AI-HTR) relay circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater (AI-HTR) relay circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM CPUs malfunction (1 trip detection logic)
- P1613Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P1614Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of following conditions met (1 trip detection logic): · Motor driver IC diagnosis signal failure ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111Throttle actuator does not close when signaled by ECM (1 trip detection logic)
- P2112Throttle actuator does not open when signaled by ECM (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic): (1) Difference between VPA and...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage more...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage less...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage more...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) A/F sensor voltage less...
- P219AThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219BThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2239A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2242A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2401P2401
- P2402P2402
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (ON) less...
- P2431Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2432While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2433While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2436Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2437While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2438While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2441The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip...
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2443The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip...
- P2444Secondary air pressure more than 3.0 kPa (23 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2445Secondary air pressure less than 1.9 kPa (14 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2446Secondary air pressure more than 3.0 kPa (23 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2447Secondary air pressure less than 1.9 kPa (14 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2610ECM internal malfunction (2 trip detection logic)
- P0010An open or short in the Camshaft Oil Control Valve (OCV) for intake side (for Bank 1) circuit (1 trip...
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0013An open or short in the Camshaft Oil Control Valve (OCV) for exhaust side (for Bank 1) circuit (1 trip...
- P0014The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0014The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0015The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0015The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0016Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Camshaft Bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Camshaft Bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Camshaft Bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Camshaft Bank 2) signal (2 trip...
- P0020An open or short in the OCV for intake side (for Bank 2) circuit (1 trip detection logic).
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0023An open or short in the OCV for exhaust side (for Bank 2) circuit (1 trip detection logic).
- P0024The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0024The exhaust valve timing is not adjusted in the valve timing advance range (2 trip detection logic).
- P0025The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0025The exhaust valve timing is not adjusted in the valve timing retard range (1 trip detection logic).
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0031Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0051Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0051Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic).
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic).
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0101Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic): (a) Engine...
- P0102MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic: Engine speed is less than 4000 rpm)...
- P0103MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic: Engine speed is less than 4000 rpm)...
- P0111When either of following conditions is met (2 trip detection logic): 1. In duration between engine warmed up...
- P0112Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116When either of following conditions met (2 trip detection logic): · When cold engine started and engine...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P0120Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more...
- P0121The difference between the VTA1 and VTA2 voltages is below 0.8 V or higher than 1.6 V for 2 seconds or less...
- P0122Output voltage of VTA1 0.2 V or less for 2 seconds or more (1 trip detection logic)
- P0123Output voltage of VTA1 4.535 V or more for 2 seconds or more (1 trip detection logic)
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0139The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P0139The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P013AThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013AThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013CThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013CThe HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P014CThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014CThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014DThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014DThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014EThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014EThe "Rich to Lean response rate deterioration level*" value is less than the standard. (2 trip detection...
- P014FThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P014FThe "Lean to Rich response rate deterioration level*" value is more than the standard. (2 trip detection...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0159The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P0159The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
- P015AThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015AThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015BThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015CThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015CThe "Rich to Lean delay level*" value is less than the standard. (2 trip detection logic)
- P015DThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P015DThe "Lean to Rich delay level*" value is more than the standard. (2 trip detection logic)
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more...
- P0222Output voltage of VTA2 1.75 V or less for 2 seconds or more (1 trip detection logic)
- P0223Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds or more (1 trip...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2...
- P0301Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0301Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0327Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P032COutput voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P032DOutput voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P0335· No CKP sensor signal to ECM while cranking (1 trip detection logic) · No CKP sensor signal to ECM at engine...
- P0337Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
- P0338Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
- P0339Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection...
- P033COutput voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P033DOutput voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0340No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
- P0342The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip...
- P0343The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1...
- P0345No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
- P0347The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip...
- P0348The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1...
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0355No IGF signal to ECM while engine running (1 trip detection logic)
- P0356No IGF signal to ECM while engine running (1 trip detection logic)
- P0357No IGF signal to ECM while engine running (1 trip detection logic)
- P0358No IGF signal to ECM while engine running (1 trip detection logic)
- P0365No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0367Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0368Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0390No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
- P0392Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P0393Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P0412After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0415After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0418After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0419After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0420OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0420OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P043E, P043F, P2401, P2402 and P2419 present when one of following conditions met during key-off EVAP...
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0443Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV (1 trip...
- P0451Sensor output voltage fluctuates frequently within a certain time period.
- P0452EVAP pressure less than 42.11009 kPa for 0.5 seconds.
- P0453EVAP pressure more than 123.8 kPa for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic)
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON...
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P0550Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine...
- P0552Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running. (1 trip...
- P0553Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running. (1 trip...
- P0560Open in ECM back up power source circuit (1 trip detection logic)
- P0604ECM RAM errors
- P0606When either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0607· ECM CPUs malfunction · HO2S transistors malfunction
- P060AWhen either condition below is met: · ECM main CPU error · ECM sub CPU error · Electronic throttle monitoring...
- P060BECM main CPU communication error
- P060DWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P060EWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0617When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20...
- P062FECM internal error (EEPROM)
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0657Throttle actuator power supply error
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P106BThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P144COpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM CPUs malfunction
- P1613Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P1614Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of following conditions met (1 trip detection logic): · Hybrid IC diagnosis signal failure · Hybrid IC...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111Throttle actuator does not close when signaled by ECM (1 trip detection logic)
- P2112Throttle actuator does not open when signaled by ECM (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic): (1) Difference between VPA and...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2239A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2239A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2242A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2242A1A+/A2A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2401P2401
- P2402P2402
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (ON) less...
- P2431Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2432While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2433While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2436Pressure sensor indicates less than 45.6 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2437While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2438While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2440The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2440The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2441The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2441The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2442The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2442The pressure sensor detects pulsation of the exhaust gas despite the ECM commanding the Air Switching Valve...
- P2443The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2443The pressure sensor detects no pulsation of the exhaust gas despite the ECM commanding the Air Switching...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2610ECM internal malfunction
- P2610ECM internal malfunction
- P0010Open or short in OCV (for intake side of bank 1) circuit (1 trip detection logic)
- P0011Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0013Open or short in OCV (for exhaust side of bank 1) circuit (1 trip detection logic)
- P0014Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0015Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0016Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Side of Bank 1) signal (2 trip...
- P0017Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Side of Bank 1) signal (2 trip...
- P0018Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Side of Bank 2) signal (2 trip...
- P0019Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Side of Bank 2) signal (2 trip...
- P0020Open or short in OCV (for intake side of bank 2) circuit (1 trip detection logic)
- P0021Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0022Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0023Open or short in OCV (for exhaust side of bank 2) circuit (1 trip detection logic)
- P0024Exhaust valve timing is not adjusted in valve timing advance range (2 trip detection logic)
- P0025Exhaust valve timing is not adjusted in valve timing retard range (1 trip detection logic)
- P0031Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0032Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0037The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0038The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0051Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
- P0052Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic)
- P0057The heater current is less than the specified value while the heater is operating. (1 trip detection logic)
- P0058The heater current is higher than the specified value while the heater is operating. (1 trip detection logic)
- P0101Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic): (a) Engine...
- P0102Mass Air Flow (MAF) meter voltage less than 0.2 V for 3 seconds (1 trip detection logic: Engine speed less...
- P0103MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic: Engine speed less than 4000 rpm) (2...
- P0111When either condition below is met: 1. The intake air temperature change is small, from the previous trip...
- P0112Short in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116When either of following conditions met (2 trip detection logic): · When cold engine started and engine...
- P0117Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
- P011BAll of the following conditions are met (2 trip detection logic): 1. The battery voltage is 10.5 V or higher....
- P0120Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0121Difference between VTA1 and VTA2 voltages less than 0.8 V or more than 1.6 V for 2 seconds (1 trip detection...
- P0122Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0123Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0125Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0128Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic): (a) Cold start (b) Engine warmed up...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0136· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0137· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0138· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0139· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P0139· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P013A· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013A· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P013C· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection...
- P013C· HO2 sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (2 trip detection...
- P0141The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014CThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014DThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014EThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014EThe "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic).
- P014FThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P014FThe "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic).
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0156· Abnormal voltage output: During active air-fuel ratio control, following conditions (a) and (b) met for...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0157· Low voltage (open): During active air-fuel ratio control, following conditions (a) and (b) met for certain...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0158· Extremely high voltage (short): HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip...
- P0159· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P0159· HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic)
- P015AThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015AThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015BThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015BThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015CThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015CThe "Rich to Lean delay level*" value is standard or more (2 trip detection logic).
- P015DThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P015DThe "Lean to Rich delay level*" value is standard or more (2 trip detection logic).
- P0161The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic)
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0174With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0175With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when...
- P0222Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic)
- P0223Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal...
- P0230When either condition below is met (1 trip detection logic): · When fuel pump is operating: · Remaining fuel...
- P0300Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2...
- P0301Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0302Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0303Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0304Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0305Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0306Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0307Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0308Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection...
- P0327Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0328Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P032COutput voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P032DOutput voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0332Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic)
- P0333Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more (1 trip detection logic)
- P0335· No CKP sensor signal to ECM while cranking (1 trip detection logic) · No CKP sensor signal to ECM at engine...
- P0337Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
- P0338Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
- P0339Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection...
- P033COutput voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic)
- P033DOutput voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more (1 trip detection logic)
- P0340No VVT sensor (for intake side) signal to ECM during engine running (1 trip detection logic)
- P0342Output voltage of VVT sensor (for intake side) less than 0.3 V for 4 seconds (1 trip detection logic)
- P0343Output voltage of VVT sensor (for intake side) more than 4.7 V for 4 seconds (1 trip detection logic)
- P0345No VVT sensor (for intake side) signal to ECM during engine running (1 trip detection logic)
- P0347Output voltage of VVT sensor (for intake side) less than 0.3 V for 4 seconds (1 trip detection logic)
- P0348Output voltage of VVT sensor (for intake side) more than 4.7 V for 4 seconds (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0355No IGF signal to ECM while engine running (1 trip detection logic)
- P0356No IGF signal to ECM while engine running (1 trip detection logic)
- P0357No IGF signal to ECM while engine running (1 trip detection logic)
- P0358No IGF signal to ECM while engine running (1 trip detection logic)
- P0365No VVT sensor (for exhaust side) signal to ECM during engine running (1 trip detection logic)
- P0367Output voltage of VVT sensor (for exhaust side) less than 0.3 V 4 seconds (1 trip detection logic)
- P0368Output voltage of VVT sensor (for exhaust side) more than 4.7 V 4 seconds (1 trip detection logic)
- P0390No VVT sensor (for exhaust side) signal to ECM during engine running (1 trip detection logic)
- P0392Output voltage of VVT sensor (for exhaust side) less than 0.3 V 4 seconds (1 trip detection logic)
- P0393Output voltage of VVT sensor (for exhaust side) more than 4.7 V 4 seconds (1 trip detection logic)
- P0412After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0415After cold engine starts, all of following conditions met (1 trip detection logic): 1. Secondary Air...
- P0418After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0419After cold engine starts, all of following conditions met (2 trip detection logic): 1. Secondary Air...
- P0420OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0420OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (1 trip detection logic)
- P0430OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
- P043E, P043F, P2401, P2402 and P2419 present when one of following conditions met during key-off EVAP...
- P043FP043F
- P0441Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0451Sensor output voltage fluctuates frequently within a certain time period.
- P0452EVAP pressure less than 42.11009 kPa-a for 0.5 seconds.
- P0453EVAP pressure more than 123.76147 kPa-a for 0.5 seconds.
- P0455Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0456Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure measured....
- P0461Despite consuming a certain amount of fuel, the change in the resistance value of the fuel sender gauge is...
- P0462The resistance value of the fuel sender gauge is below the threshold. (2 trip detection logic)
- P0463The resistance value of the fuel sender gauge exceeds the threshold. (2 trip detection logic)
- P0500While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic)
- P0504Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON...
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P0505Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050AInsufficient mass air flow at cold start (2 trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P050BInsufficient ignition timing retard at cold start (2-trip detection logic)
- P0550Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine...
- P0552Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running. (1 trip...
- P0553Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running. (1 trip...
- P0560Open in ECM back up power source circuit (1 trip detection logic)
- P0604ECM RAM errors
- P0606When either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0607· ECM CPUs malfunction · Heated oxygen sensor transistor (built into the ECM) malfunction
- P060AWhen either condition below is met: · ECM main CPU error · ECM sub CPU error · Electronic throttle monitoring...
- P060BECM main CPU communication error
- P060DWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P060EWhen either condition below is met: · ECM main CPU error · ECM sub CPU error
- P0617When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20...
- P062FECM internal error (EEPROM)
- P0630When either condition below is met: (1 trip detection logic) · VIN not stored in ECM · Input VIN incorrect
- P0657Throttle actuator power supply error
- P0724Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less...
- P101DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating. (1 trip detection...
- P106BThe pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the...
- P109CThe fuel pressure switching valve relay circuit is open or shorted to ground. (1 trip detection logic)
- P109DThe fuel pressure switching valve relay circuit is shorted to the power supply. (1 trip detection logic)
- P1340No camshaft position sensor signal to ECM during cranking (2 trip detection logic)
- P1342Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic)
- P1343Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic)
- P144COpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is below 500 rpm with the STA signal on for a certain amount of...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1607ECM CPUs malfunction
- P1613Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P1614Either of following conditions (1) or (2) met: (1) All of following conditions met (1 trip detection logic):...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of following conditions met (1 trip detection logic): · Hybrid IC diagnosis signal failure · Hybrid IC...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111Throttle actuator does not close when signaled by ECM (1 trip detection logic)
- P2112Throttle actuator does not open when signaled by ECM (1 trip detection logic)
- P2118Open in ETCS power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2122VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2123VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b)...
- P2135Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2197Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2198Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P219AThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219BThe difference in air-fuel ratios between the cylinders exceeds the threshold.
- P219CThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219DThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219EThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P219FThe difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A0The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A1The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A2The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P21A3The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic).
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2237Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2238· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2239Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2239Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2240Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2241· Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+...
- P2242Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2242Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage more...
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2252A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2253A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2255A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2256A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
- P2401P2401
- P2402P2402
- P2419P2419
- P2420Following condition met during key-off EVAP monitor: · EVAP pressure change when vent valve closed (ON) less...
- P2431Pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2432While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2433While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2436Pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection...
- P2437While engine running, voltage output of pressure sensor remains below 0.5 V (1 trip detection logic)
- P2438While engine running, voltage output of pressure sensor remains above 4.5 V (1 trip detection logic)
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2441The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip...
- P2441The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip...
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2443The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip...
- P2443The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2444Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2445Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2446Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2447Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on (2 trip...
- P2610ECM internal malfunction
- U0155Following conditions are met for 2.9 seconds (1 trip detection logic): 1. Ignition switch to ON. 2. Battery...
- P0500Vehicle speed signal from vehicle speed sensor is cut for 0.14 seconds. or more while cruise control is in...
- P0503Momentary interruption and noise are detected when a rapid change of vehicle speed occurs while cruise...
- P0571When voltage of STP terminal and ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more
- P0575When either of following conditions is met: · Cruise control input signal abnormal · Stop light switch input...
- P0705One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either of the following...
- P0717All conditions are met for 5 seconds or more (1-trip detection logic): (a) Gear change is not performed. (b)...
- P0722All conditions are met for 5 seconds or more continuously (2-trip detection logic): (a) No signal from speed...
- P07296th gear shift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the transmission to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781Conditions (a) and (b), or (a) and (c) are met (2-trip detection logic): (a) When the ECM directs the...
- P0894The ECM detects a malfunction in shift solenoid valve SLT, S1, S2, S3, S4 or SL2, or the 1-2 shift valve, or...
- P0973ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip...
- P0974ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip...
- P0976ECM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip...
- P0977ECM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip...
- P0979ECM detects a short in the solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip...
- P0980ECM detects an open in the solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1-trip...
- P0982ECM detects a short in the solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip...
- P0983ECM detects an open in the solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip...
- P0985ECM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip...
- P0986ECM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip...
- P2714The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of...
- P2716Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more (1-trip detection...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in the shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- P0705One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either of the following...
- P0717All conditions are met for 5 seconds or more (1-trip detection logic): (a) Gear change is not performed. (b)...
- P0722All conditions are met for 5 seconds or more continuously (2-trip detection logic): (a) No signal from speed...
- P07296th gear shift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the transmission to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781Conditions (a) and (b), or (a) and (c) are met (2-trip detection logic): (a) When the ECM directs the...
- P0894The ECM detects a malfunction in shift solenoid valve SLT, S1, S2, S3, S4 or SL2, or the 1-2 shift valve, or...
- P0973ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip...
- P0974ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip...
- P0976ECM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip...
- P0977ECM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip...
- P0979ECM detects a short in the solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1-trip...
- P0980ECM detects an open in the solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1-trip...
- P0982ECM detects a short in the solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip...
- P0983ECM detects an open in the solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip...
- P0985ECM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip...
- P0986ECM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1-trip...
- P2714The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of...
- P2716Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more (1-trip detection...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in the shift solenoid valve SLU circuit for 1 second or more while driving (1-trip...
- P2772Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions...
- P2772Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions...
- P0705When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1 trip detection logic)
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more either of the following...
- P0717All conditions below are detected for 5 seconds or more (1-trip detection logic) (a) Gear change is not...
- P0722All conditions below are detected 5 seconds or more continuously (2-trip detection logic) (a) No signal from...
- P0724The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (1.86 mph)) and...
- P07296th gearshift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic) (a) When the ECM directs the...
- P0894The ECM detects a malfunction on SLT, S1, S2, S3, S4, SL2, gear 6 incorrect ratio (sequence valve) or 1-2...
- P0973ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1 trip...
- P0979ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1 trip detection...
- P0980ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1 trip...
- P0982ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection...
- P0983ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip...
- P0985ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection...
- P0986ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip...
- P2714The ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more. (1-trip...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip...
- P0705When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0711Either condition is met (2-trip detection logic): (a) Certain monitor enabling conditions are met and the ATF...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1 trip detection logic)
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more either of the following...
- P0717All conditions below are detected for 5 seconds or more (1-trip detection logic) (a) Gear change is not...
- P0722All conditions below are detected 5 seconds or more continuously (2-trip detection logic) (a) No signal from...
- P0724The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (1.86 mph)) and...
- P07296th gearshift malfunction: The ECM determines there is a malfunction when both of the following conditions...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751S1 stuck ON malfunction*1: The ECM determines there is a malfunction when the following conditions are both...
- P0756S2 stuck ON malfunction*1: Shifting to 3rd and 5th gears is impossible. The ECM determines there is a...
- P0761S3 stuck ON malfunction*1: When the ECM directs the gearshift to switch to 5th or 6th gear, the engine...
- P0766S4 stuck OFF malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0776SL2 stuck ON malfunction or brake control valve malfunction*: Shifting to 5th and 6th gears is impossible....
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic) (a) When the ECM directs the...
- P0894The ECM detects a malfunction on SLT, S1, S2, S3, S4, SL2, gear 6 incorrect ratio (sequence valve) or 1-2...
- P0973ECM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1 trip...
- P0979ECM detects short in solenoid valve S3 circuit 2 times when solenoid valve S3 is operated (1 trip detection...
- P0980ECM detects open in solenoid valve S3 circuit 2 times when solenoid valve S3 is not operated (1 trip...
- P0982ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection...
- P0983ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip...
- P0985ECM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection...
- P0986ECM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip...
- P2714The ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2742No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more. (1-trip...
- P2743No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either...
- P2757Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up...
- P2759Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip...
- P2772Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions...
- P2772Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions...
- P05601. The ignition switch is ON and the transfer position switch is operated 2. Open circuit or short to ground...
- P17A01. Ignition switch ON (when not switching between 2WD and 4H) 2. Open circuit in the A.D.D. shift motor drive...
- P17A11. Ignition switch ON (when not switching between 2WD and 4H) 2. Short to ground in the A.D.D. shift motor...
- P17A21. Ignition switch ON (when not switching between 2WD and 4H) 2. Short to B+ in the A.D.D. shift motor drive...
- P17A41. Ignition switch is ON and engine is running 2. Limit switch DL1 terminal is OFF (OPEN) and the DL2...
- P17A51. Ignition switch ON (when not switching between 2WD and 4H) 2. Open circuit in the solenoid coil drive...
- P17A61. Ignition switch ON (when switching between 2WD and 4H) 2. Short to ground in the solenoid coil drive...
- P17A71. Ignition switch ON (when not switching between 2WD and 4H) 2. Short to B+ in the solenoid coil drive...
- P17A81. Ignition switch ON (when transfer shift motor is not operating) 2. Open circuit in the transfer shift...
- P17A91. Ignition switch ON (when transfer shift motor is not operating) 2. Short to ground in the transfer shift...
- P17AA1. Ignition switch ON (when transfer shift motor is not operating) 2. Short to B+ in the transfer shift motor...
- P17AB1. Immediately after turning the ignition switch to ON and driving mode is being switched 2. Short to ground...
- P17AC1. When the ignition switch is ON, the engine is running, and the driving mode is being switched 2. The...
- P27721. Ignition switch is ON and engine is running 2. H4 terminal signal is OFF (OPEN) and L4 terminal signal is...
- P279E1. Ignition switch is ON and engine is running 2. 2-4 terminal signal is OFF (OPEN) and LO terminal signal is...
- U01001. Ignition switch ON 2. Communication is lost between ECM and 4 wheel drive control ECU 3. 5 seconds or more...
- U01221. Ignition switch ON 2. Communication is lost between skid control ECU and 4 wheel drive control ECU 3. 0.7...
- U04161. Ignition switch ON 2. Wheel speed sensor malfunction signals from skid control ECU are received 3. 0.06...
- C2121/21 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2122/22 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2123/23 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2124/24 When all conditions below are met: · Tire pressure warning valve and transmitter is not in stop mode · Signal...
- C2126/26 After ID registration is completed, until all tire pressure warning valve and transmitter IDs are received by...
- C2141/41 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2142/42 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2143/43 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2144/44 The battery of the tire pressure warning valve and transmitter is depleted or G-SW in the tire pressure...
- C2165/65 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified times.
- C2166/66 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified times.
- C2167/67 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified times.
- C2168/68 Temperature inside the tire exceeds 119°C (246.2°F) more than a specified times.
- C2171/71 Transmitter ID is not registered. (When a transmitter ID is unregistered for 3 minutes or more)
- C2174/74 Vehicle speed signal malfunction
- C2176/76 Malfunction in the tire pressure warning ECU internal circuit.
- C2177/77 When all conditions below are met: · During initialization · Signal is not received from tire pressure...
- C2178/78 With ignition switch ON, when IG voltage of less than 10 V continues for 20 minutes or more, or IG voltage of...
- C2181/81 Test mode procedure is performed.
- C2182/82 Test mode procedure is performed.
- C2183/83 Test mode procedure is performed.
- C2184/84 Test mode procedure is performed.
- C2191/91 Test mode procedure is performed
- C0200/31 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)...
- C0205/32 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)...
- C0210/33 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)....
- C0215/34 When any of following conditions detected: 1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph)....
- C0226/21 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0236/22 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0246/23 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0256/24 Open or short in solenoid circuit continues for 0.05 seconds or more.
- C0273/13 When one of following conditions is met: 1. Pump motor voltage is 2.0 V or more for 1 sec. or more at motor...
- C0278/11 When either of following conditions detected: 1. Malfunction in skid control ECU continues for 0.056 seconds...
- C1201/51 Engine control system malfunction signal continues for 1.2 seconds.
- C1203/53 When all of following conditions detected: 1. Engine variation data from ECM does not match one in skid...
- C1207/37 When all conditions below are met: · Yaw rate sensor is normal. · G sensor lateral operation is normal. ·...
- C1225/25 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1226/26 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1227/27 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1228/28 When any of following conditions detected: 1. During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal...
- C1231/31 When any of following conditions detected: 1. The ECU-B1 fuse blows or the ignition switch is turned to ON...
- C1232/32 When any of following conditions detected: 1. Malfunctions in deceleration sensor detected through...
- C1234/34 Sensor malfunction signal received from yaw rate sensor
- C1241/41 When any of following conditions detected: 1. +BS terminal voltage 18 V or more (momentary occurrence...
- C1244/44 G sensor forward and backward operation is malfunctioning (4WD)
- C1247/47 When either condition below is met: 1. When the output becomes 4.7 V or more or 0.2 V or less per 100 msec....
- C1249/49 When one of following conditions is met: 1. When voltage of STP2 pin is detected to be outside range of 1.4...
- C1251/51 When any of following conditions detected with normal battery voltage (10 V or more): 1. Open in pump motor...
- C1267/28 When one of following conditions is met: 1. Micro switch signal PSNC and PSNO logic malfunction. 2. When...
- C1271/71 Detected only during test mode.
- C1272/72 Detected only during test mode.
- C1273/73 Detected only during test mode.
- C1274/74 Detected only during test mode.
- C1275/75 Detected only during test mode.
- C1276/76 Detected only during test mode.
- C1277/77 Detected only during test mode.
- C1278/78 Detected only during test mode.
- C1279/79 Detected only during test mode
- C1281/81 Detected only during test mode.
- C1290/66 Steering angle sensor zero point deviates from zero point stored in skid control ECU by 20 degrees or more.
- C1300/62 Malfunction in skid control ECU
- C1310/11 Open or short in active brake booster solenoid circuit.
- C1311/12 Open or short circuit is detected.
- C1330/35 Open in front speed sensor circuit continues for 0.15 seconds or more.
- C1331/36 Open in front speed sensor circuit continues for 0.15 seconds or more.
- C1332/37 Open in rear speed sensor circuit continues for 0.15 seconds or more.
- C1333/38 Open in rear speed sensor circuit continues for 0.15 seconds or more.
- C1336/39 When the vehicle is driven without completion of zero point calibration.
- C1340/47 When the terminal IG1 voltage is between 10 and 14 V, there is an open in the A.D.D. detection switch circuit...
- C1360/61 When any of the following conditions are detected: 1. When malfunction occurs during pressure sensor initial...
- C1370/73 Information relating to engine, transmission, drivetrain or destination stored in ECM does not match...
- C1380/64 Open or short circuit is detected.
- C1439/66 After the steering angle sensor zero point calibration data is cleared due to, for example, fluctuations in...
- C1445/66 Steering angle sensor zero point is not obtained when the vehicle is driven without a record of steering...
- U0073/94 Bus off conditions continue for approximately 0.8 seconds.
- U0100/65 CAN signal from ECM is lost or malfunctioning for 1.2 seconds.
- U0114/27 CAN signal from 4WD control ECU is lost or malfunctioning for 1.2 seconds.
- U0123/62 Supplied voltage normal (9.7 V or more), skid control ECU receives no yaw rate sensor data for 0.1 seconds.
- U0124/69 Supplied voltage normal (9.7 V or more), skid control ECU receives no yaw rate sensor data for 0.1 seconds.
- U0126/63 Supplied voltage normal (9.7 V or more), skid control ECU receives no steering angle sensor data for 0.1...
- C14A0When either of following conditions detected: 1. Manual trailer brake output slider output value continuously...
- C14A1When either of following conditions detected: 1. After gain value of 10 (maximum output) is input, GAIN (+)...
- C14A2When either of following conditions detected: 1. After gain value of 0 (no trailer brake) is input, GAIN (-)...
- C14A3When either of following conditions detected: 1. Trailer brake TYPE selection button input signal continuous...
- C14A4When either of following conditions detected: 1. Trailer brake control ECU (Brake control with bracket relay)...
- C14A5When trailer brake control ECU (brake control with bracket relay) is not performing control, output signal...
- C14A6Voltage is continuously input to trailer brake control ECU (brake control with bracket relay) output circuit...
- C14A7When either of following conditions detected: 1. Trailer brake control ECU (Brake control with bracket relay)...
- U0101CAN signal from ECM is lost or malfunctioning for 5.1 seconds.
- U0129CAN signal from skid control ECU is lost or malfunctioning for 3 seconds.
- U0155CAN signal from combination meter is lost or malfunctioning for 3.3 seconds.
- B2602When both conditions below are met: · Unlock warning switch signal is OFF. · Ignition switch is turned ON.
- B2603When operating the tilt and telescopic manual switch, abnormal voltage value is input to the multiplex tilt...
- B2610Tilt operation stops within the operation range while operating.
- B2611Telescopic operation stops within the operation range while operating.
- B2620While the auto away/return function, driving position memory function or manual control is in operation, the...
- B2621The periodic signal from a specified ECU has stopped.
- B2624When either condition below is met: · The auto away function is disabled with the last vehicle speed signal*...
- B1532When either condition below is met:. · The stereo component tuner assembly is not connected while the...
- B1551When one of the conditions below is met: · "HD Radio" tuner decoder malfunction · "HD Radio" tuner audio...
- B156CB156C
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either of the conditions below is met: · Bus malfunction · EEPROM error
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B4When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B5When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15BAWhen either of the conditions below is met: · Internal IC malfunction · Tuner malfunction
- B15C3A short is detected in the speaker output circuit.
- B15F6Main body ECU (driver side junction block assembly) vehicle setting processing error.
- B15F8Position control ECU and switch assembly vehicle setting processing error.
- B15FESatellite radio antenna is not connected.
- B15FFA short occurs in satellite radio antenna.
- U0073CAN bus connection error
- U0100CAN reception error
- U0129CAN reception error
- U0140CAN reception error
- U0155CAN reception error
- U0164CAN reception error
- B1532When either condition below is met: · Video signal (digital) is lost. · The stereo component tuner assembly...
- B1551When one of the conditions below is met: · "HD Radio" tuner decoder malfunction · "HD Radio" tuner audio...
- B1552Internal malfunction of the extension module
- B156CB156C
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158AScreen noise adjustment fails
- B158CThe SD card cannot be mounted when inserted into the SD card slot.
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either of the conditions below is met: · Bus malfunction · EEPROM error
- B15A3When one of the conditions below is met: · Internal power supply malfunction · DSP error · EEPROM error
- B15ADWhen one of the conditions below is met: · Short to ground or +B, or open occurs in gyro signal circuit ·...
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B4When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15BAWhen either of the conditions below is met: · Internal IC malfunction · Tuner malfunction
- B15C0Navigation antenna error
- B15C1Error of the power source to the navigation antenna
- B15C2A difference between the GPS speed and SPD pulse is detected.
- B15C3A short is detected in the speaker output circuit.
- B15D3When either condition below is met: · Stereo component amplifier assembly is/was not connected while the...
- B15F5Air conditioning amplifier assembly vehicle setting processing error.
- B15F6Main body ECU (driver side junction block assembly) vehicle setting processing error.
- B15F8Front power seat switch LH vehicle setting processing error.
- B15FESatellite radio antenna is not connected.
- B15FFA short occurs in satellite radio antenna.
- U0073CAN bus connection error
- U0100CAN reception error
- U0129CAN reception error
- U0140CAN reception error
- U0155CAN reception error
- U0164CAN reception error
- C1622Open or Short Circuit in television camera signal
- C1622Open or Short Circuit in television camera signal
- C1A45A fail flag is transmitted from the skid control ECU (brake actuator assembly).
- C1A47A fail flag is transmitted from the steering sensor
- C1AB0With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1AB1With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied...
- C1AB2With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB3With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output...
- C1AB4With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB5With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing...
- C1AB6The blind spot monitor sensor RH (master) detects an internal malfunction.
- C1AB7The blind spot monitor sensor LH (slave) detects an internal malfunction.
- C1AB8The blind spot monitor sensor cannot communicate with the main body ECU (driver side junction block assembly).
- C1ABBA beam axis inspection has not been performed.
- C1ABCA beam axis inspection has not been performed.
- C1ABDBoth of the following conditions are met: · Blind spot monitor main switch assembly (warning canceling switch...
- C1ABEBoth of the following conditions are met: · Blind spot monitor main switch assembly (warning canceling switch...
- C1AC1When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is...
- C1AC1When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is...
- C1AC2When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is...
- C1AC2When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is...
- U0100Lost communication with ECM
- U0126Lost communication with steering sensor
- U0129Lost communication with skid control ECU (brake actuator assembly)
- U0142Lost communication with main body ECU (driver side junction block assembly)
- U0232The blind spot monitor sensor RH cannot receive signals from the blind spot monitor sensor LH.
- U1331Destination information of the main body ECU (driver side junction block assembly) and blind spot monitor...
- B1206No communication between the power window regulator master switch assembly and main body ECU (driver side...
- B1273No communication between sliding roof drive gear sub-assembly and main body ECU (driver side junction block)...
- B2321No communication between the front power window regulator motor assembly LH and main body ECU (driver side...
- B2322No communication between the front power window regulator motor assembly RH and main body ECU (driver side...
- B2325The main body ECU (driver side junction block) detects a malfunction in the LIN communication bus between...
- U0199There is no communication from the outer mirror control ECU assembly.
- U0208There is no communication from the front power seat control ECU with switch LH.
- U0233There is no communication from the blind spot monitor sensor RH.
- U1002(CAN No. 2 BUS)
- U1002Lost communication with gateway module
- U1115There is no communication from the multiplex tilt and telescopic ECU.
- B1000/31 Center airbag sensor assembly malfunction
- B1610/13 When one of the following conditions is met: · Front airbag sensor RH malfunction · Center airbag sensor...
- B1615/14 When one of the following conditions is met: · Front airbag sensor LH malfunction · Center airbag sensor...
- B1620/21 When one of the following conditions is met: · Side airbag sensor LH malfunction · Center airbag sensor...
- B1625/22 When one of the following conditions is met: · Side airbag sensor RH malfunction · Center airbag sensor...
- B1630/23 When one of the following conditions is met: · Side airbag sensor LH malfunction · Center airbag sensor...
- B1635/24 When one of the following conditions is met: · Side airbag sensor RH malfunction · Center airbag sensor...
- B1650/32 When one of the following conditions is met: · Occupant classification system malfunction · The center airbag...
- B1653/35 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal,...
- B1655/37 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal,...
- B1660/43 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal, a...
- B1690/15 When one of the following conditions is met: · Door side airbag sensor LH malfunction · Center airbag sensor...
- B1695/16 When one of the following conditions is met: · Door side airbag sensor RH malfunction · Center airbag sensor...
- B1800/51 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1801/51 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1802/51 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1803/51 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1805/52 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1806/52 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1807/52 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1808/52 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1810/53 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1811/53 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1812/53 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1813/53 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1815/54 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1816/54 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1817/54 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1818/54 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B181A/7A When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B181B/7A When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B181C/7A When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B181D/7A When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1820/55 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1821/55 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1822/55 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1823/55 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1825/56 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1826/56 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1827/56 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1828/56 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1830/57 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1831/57 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1832/57 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1833/57 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1835/58 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1836/58 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1837/58 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1838/58 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1860/64 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1861/64 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1862/64 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1863/64 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1865/65 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1866/65 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1867/65 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1868/65 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1900/73 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1901/73 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1902/73 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1903/73 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1905/74 When one of the following conditions is met: · The center airbag sensor receives a line short circuit signal...
- B1906/74 When one of the following conditions is met: · The center airbag sensor receives an open circuit signal in...
- B1907/74 When one of the following conditions is met: · The center airbag sensor receives a short circuit to ground...
- B1908/74 When one of the following conditions is met: · The center airbag sensor receives a short circuit to B+ signal...
- B1771One of following conditions is met: · Occupant classification ECU detects line short circuit signal, open...
- B1780One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1781One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1782One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1783One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1785Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1786Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1787Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1788Either of following conditions is met: · Occupant classification ECU receives collision detection signal,...
- B1790One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1793One of following conditions is met: · Occupant classification ECU receives line short circuit signal, open...
- B1794One of following conditions is met: · Occupant classification ECU circuit malfunction · Occupant...
- B1795Occupant classification ECU malfunction
- B1796Occupant classification ECU malfunction
- B1411/11 Open or short in room temperature sensor circuit
- B1412/12 Open or short in ambient temperature sensor circuit
- B1412/12 Open or short in ambient temperature sensor circuit
- B1413/13 Open or short in evaporator temperature sensor circuit
- B1413/13 Open or short in evaporator temperature sensor circuit
- B1421/21 Open or short in passenger side solar sensor circuit
- B1422/22 Open or short in compressor lock sensor circuit
- B1422/22 Open or short in compressor lock sensor circuit
- B1423/23 Open or short in pressure switch circuit
- B1423/23 Open or short in pressure switch circuit
- B1424/24 Open or short in driver side solar sensor circuit
- B1441/41 Air mix damper position sensor value does not change even if air conditioning amplifier operates No. 1 damper...
- B1441/41 Air mix damper position sensor value does not change even if air conditioning amplifier operates air mix...
- B1442/42 Air inlet damper position sensor value does not change even if air conditioning amplifier operated air inlet...
- B1442/42 Air inlet damper position sensor value does not change even if air conditioning amplifier operated air inlet...
- B1443/43 Air outlet damper position sensor value does not change even if air conditioning amplifier operates No. 1...
- B1443/43 Air outlet damper position sensor value does not change even if air conditioning amplifier operates No. 1...
- B1445/45 Cool air bypass servo motor position sensor value does not change even if air conditioning amplifier operates...
- B1446/46 Air mix damper position sensor value does not change even if air conditioning amplifier operates No. 1 damper...
- B1497/97 Communication line error or open
- B1497/97 Communication line error or open
- B1499/99 Open in CAN communication circuit
- B1499/99 Open in CAN communication circuit
- B2780Unlock warning switch ON is not detected when the ignition switch is ON.
- B2784Antenna coil is open/shorted
- B2793Transponder chip malfunction
- B2794Key with incomplete key code is inserted
- B2795Key with unregistered key code is inserted
- B2796The key code cannot be transmitted
- B2797Keys are positioned too close to each other, or noise occurred in communication line
- B2798Key code identification cannot be completed within the specified time
- B2799One of following conditions is met: · Error in communication between ECM and transponder key ECU · Error in...
- B279AWhen communication line (EFIO-IMI) between ECM and transponder key ECU is stuck on HI output for 6 seconds or...
- B279CECM for vehicle without engine immobiliser system is installed on vehicle with engine immobiliser system
- B1500When combination meter detects fuel sender gauge malfunction
- U0100When either of following conditions is detected: · Vehicle speed 5 km/h (3 mph) or more and IG voltage 10.5 V...
- U0129When either of following conditions is detected: · 15 seconds have elapsed since engine started and IG...
- U0151Lost Communication with Restraints Control Module
- B2311Either condition below is met: 1. The power window regulator motor malfunctions. 2. The ECU in the power...
- B2312· The power window regulator master switch is stuck. · The power window regulator master switch is held in...
- B2313· The power window regulator motor is not initialized. · The power window regulator motor malfunctions.
- B2650The forward and rearward lock detection position of the sensor is the same.
- B2651The forward and rearward lock detection position of the sensor is the same.
- B2652The upward and downward lock detection position of the sensor is the same.
- B2653The upward and downward lock detection position of the sensor is the same.
- B2658A problem with the voltage supplied to the position control sensor.
Common jobs · 1UR-FE (16)
- Read / clear codes
- DTC list
- Engine oil & filter: replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · installation
- Fuel pump: inspection · disassembly · reassembly
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head gasket: removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · installation
- Alternator: inspection · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · 3UR-FE (15)
- Read / clear codes
- Engine oil & filter: replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · disassembly · reassembly · installation
- Fuel pump: inspection · removal · disassembly · reassembly · installation
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head gasket: removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · installation
- Alternator: inspection · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · 3UR-FBE (15)
- Read / clear codes
- Engine oil & filter: replacement
- Ignition coil: removal · installation
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · disassembly · reassembly · installation
- Fuel pump: inspection
- Injectors: inspection · removal · installation
- Throttle body: on-vehicle inspection · inspection · removal · installation
- Cylinder head gasket: removal
- Engine assembly: on-vehicle inspection · inspection · removal · disassembly · installation
- Alternator: inspection · removal · disassembly · reassembly · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (8)
- ATF: replacement · adjustment
- Front brakes: inspection · removal · disassembly · reassembly · installation
- Rear brakes: inspection · removal · disassembly · reassembly · installation
- Brake fluid: on-vehicle inspection · replacement · bleeding
- Parking brake: inspection · disassembly · reassembly
- Front drive shaft: inspection · removal · disassembly · reassembly · installation
- Headlights: removal · disassembly · reassembly · installation · adjustment
- A/C refrigerant: on-vehicle inspection · replacement
Repair Manual
General361 documents
Engine / Hybrid System1245 documents
Drivetrain614 documents
Suspension41 documents
Brake149 documents
Steering81 documents
Audio / Visual / Telematics348 documents
Power Source / Network52 documents
Vehicle Interior1095 documents