Double Cab
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
| *a | mm (in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Tack Weld |
|
Butt Weld |
Before temporarily installing the new parts, weld the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar with the standard number of welding points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
After welding the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar to the vehicle side, install the rocker outer panel and roof side outer No. 2 rail.
After welding, apply polyurethane foam to the corresponding parts. (See the painting / coating)
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *1 | Rocker Outer Reinforce | *2 | Center Body Pillar Lower Reinforce |
| *3 | Center Body Inner Pillar | - | - |
| *a | mm (in.) | - | - |
| *1 | Rocker Outer Reinforce | *2 | Center Body Pillar Lower Reinforce |
| *3 | Center Body Inner Pillar | - | - |
| *a | mm (in.) | - | - |
| *1 | Rocker Outer Reinforce | *2 | Roof Side Outer No. 2 Rail |
CrewMax
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
|
Cut Location for Supply Parts |
| *a | mm (in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Cut and Join Location |
|
Tack Weld |
|
Butt Weld |
Before temporarily installing the new parts, weld the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar with the standard number of welding points.
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
After welding the rocker outer reinforce, center body pillar lower reinforce and center body inner pillar to the vehicle side, install the rocker outer panel and roof side outer No. 2 rail.
After welding, apply polyurethane foam to the corresponding parts. (See the painting / coating)
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *1 | Rocker Outer Reinforce | *2 | Center Body Pillar Lower Reinforce |
| *3 | Center Body Inner Pillar | - | - |
| *a | mm (in.) | - | - |
| *1 | Rocker Outer Reinforce | *2 | Center Body Pillar Lower Reinforce |
| *3 | Center Body Inner Pillar | - | - |
| *a | mm (in.) | - | - |
| *1 | Rocker Outer Reinforce | *2 | Roof Side Outer No. 2 Rail |