Home › Vehicle Exterior › BODY WELD POINT › REAR DOOR OUTER PANEL
BM27M0U _01 Vehicle Exterior _049435 BODY WELD POINT _0236697 REAR DOOR OUTER PANEL F

BODY WELD POINT  REAR DOOR OUTER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


Double Cab


K125891

a.

REMOVAL

Symbol Meaning
K108827

Cut and Join Location

REMOVAL POINT
1.

After grinding off the hemming location, remove the outer panel.


K125943C01
3.469,5.823 3.865,5.135 false 3.792,4.917 4.104,5.073 0.313,0.156 10 false *a 3.865,7.458 4.177,7.615 0.313,0.156 10 false *b
*a Hemming Location *b Disc Sander



b.

INSTALLATION

Symbol Meaning
K108831

Butt Weld
K108833

Spot MIG Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem about 30° with a hammer and dolly. Then, fasten tightly with a hemming tool.

HINT:
·

Perform hemming in three steps, being careful not to warp the panel.

·

If a hemming tool cannot be used, hem with a hammer and dolly.



3.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125944C01
5.646,4.302 6.031,4.083 false 5.521,6.646 5.958,7.073 false 6.01,3.052 6.323,3.208 0.313,0.156 10 false *a 6.073,3.979 6.385,4.135 0.313,0.156 10 false *b 6,7.042 6.313,7.198 0.313,0.156 10 false *c 6.625,8.469 6.927,8.646 0.302,0.177 10 false *d 4.198,2.958 4.802,3.208 0.604,0.25 10 false 10 (0.39) 4.521,4.688 4.802,4.917 0.281,0.229 10 false 30°
*a Do not close the drain hole. *b Cloth Tape
*c Hemming Tool *d mm (in.)




CrewMax


K125892

a.

REMOVAL

Symbol Meaning
K108827

Cut and Join Location

REMOVAL POINT
1.

After grinding off the hemming location, remove the outer panel.


K125945C01
3.458,5.823 3.771,5.417 false 3.75,5.208 4.063,5.365 0.313,0.156 10 false *a 3.854,7.458 4.167,7.615 0.313,0.156 10 false *b
*a Hemming Location *b Disc Sander



b.

INSTALLATION

Symbol Meaning
K108831

Butt Weld
K108833

Spot MIG Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem about 30° with a hammer and dolly. Then, fasten tightly with a hemming tool.

HINT:
·

Perform hemming in three steps, being careful not to warp the panel.

·

If a hemming tool cannot be used, hem with a hammer and dolly.



3.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125946C01
5.542,6.615 6.021,7.031 false 5.646,4.313 6.031,4.073 false 6.042,3.063 6.354,3.219 0.313,0.156 10 false *a 6.063,4 6.375,4.156 0.313,0.156 10 false *b 6.104,6.948 6.417,7.104 0.313,0.156 10 false *c 6.635,8.51 6.948,8.667 0.313,0.156 10 false *d 4.208,2.969 4.813,3.177 0.604,0.208 10 false 10 (0.39) 4.479,4.719 4.792,4.99 0.313,0.271 10 false 30°
*a Do not close the drain hole. *b Cloth Tape
*c Hemming Tool *d mm (in.)