Home › Vehicle Exterior › BODY WELD POINT › QUARTER PANEL
BM27M0U _01 Vehicle Exterior _049435 BODY WELD POINT _0236699 QUARTER PANEL F

BODY WELD POINT  QUARTER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


Regular Cab


K125897

a.

REMOVAL / INSTALLATION

Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108823

Plug Weld
K108824

Plug Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After welding, apply polyurethane foam to the corresponding parts. (See the painting / coating)

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the introduction)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125951C01
4.344,1.281 4.99,1.552 0.646,0.271 10 false 180 (7.09) 6.635,8.5 6.948,8.656 0.313,0.156 10 false *a
*a mm (in.) - -


K125952



Double Cab


K125898

a.

REMOVAL / INSTALLATION

Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After welding, apply polyurethane foam to the corresponding parts. (See the introduction)

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125953C01
6.573,8.458 6.885,8.615 0.313,0.156 10 false *a 4.479,1.167 5.177,1.385 0.698,0.219 10 false 180 (7.09)
*a mm (in.) - -


K125954



CrewMax


K125899

a.

REMOVAL / INSTALLATION

Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After welding, apply polyurethane foam to the corresponding parts. (See the introduction)

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125955C01
4.479,1.229 5.156,1.438 0.677,0.208 10 false 180 (7.09) 6.677,8.51 6.865,8.74 0.188,0.229 10 false *a
*a mm (in.) - -


K125956