Home › General › BODY ELECTRICAL › MULTIPLEX COMMUNICATION
NM27M0U _V1 General _050233 BODY ELECTRICAL _0241755 MULTIPLEX COMMUNICATION UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  MULTIPLEX COMMUNICATION  GENERAL/CONTROL/DETAILS  DESCRIPTION  


DESCRIPTION


a.

The multiplex communication system uses the 2 communication protocols (CAN and AVC-LAN) to achieve a streamlined wiring harness configuration.

i.

CAN (Controller Area Network) is classified into two types according to communication speed, the HS-CAN (High Speed CAN) is used for the power train, chassis and body electrical systems, and the MS-CAN (Medium Speed CAN) is used for the body electrical system.


ii.

AVC-LAN (Audio Visual Communication - Local Area Network) used for communication only between the AV (Audio Visual) system components.


iii.

The HS-CAN consists of the V bus and the MS-CAN consists of the MS bus. The Main Body ECU (Driver Side Junction Block) with gateway function is used to transmit data between the buses.


iv.

Due to the introduction of the CAN communication system for the power train, chassis and body electrical systems, the BEAN (Body Electronics Area Network) that is used for the body electrical system on other vehicles is not used on this model.


v.

A customizable body electronic system is used, enabling some of the control functions of the ECUs comprising the CAN to be set using a Techstream.




REFERENCE


a.

Generally speaking, multiplex communication refers to the use of serial communication data that consists of bits and frames in order to exchange information among various ECUs. This allows for a reduction of the amount of wiring on the vehicle.

i.

A bit is the basic unit of communication that is used to represent the information. A bit is represented by binary values of "0" or "1".


ii.

For CAN communication, a differential voltage drive is used to represent the binary values of "0" or "1". This "differential voltage drive" reduces the effects of electrical interference.

Conceptual Drawing for Multiplex Communication
Y195594E01
0.438,1.052 1.427,2.125 0.99,1.073 10 false Serial Communication Data 2.115,1.958 2.656,2.396 0.542,0.438 10 false Header 4.458,1.958 5.375,2.396 0.917,0.438 10 false End Message 3.375,0.677 4.115,0.979 0.74,0.302 10 false Frame 3.375,1.323 4,1.635 0.625,0.313 10 false Data 1.698,1.208 1.927,1.417 0.229,0.208 10 false 1 1.708,1.625 1.906,1.854 0.198,0.229 10 false 0 0.531,4.125 1.125,4.594 0.594,0.469 10 false Battery 1.958,3.135 2.656,3.458 0.698,0.323 10 false Switch 3.01,5.094 4.885,5.5 1.875,0.406 10 false Single Wire Voltage Drive 2.635,4.052 3.104,4.448 0.469,0.396 10 false ECU 4.531,4.031 4.99,4.438 0.458,0.406 10 false ECU 3.365,3.479 3.677,3.719 0.313,0.24 10 false On 3.865,3.49 4.167,3.74 0.302,0.25 10 false On 3.635,4.031 3.938,4.354 0.302,0.323 10 false Off 6.167,3.615 6.615,3.958 0.448,0.344 10 false Light 6.146,4.01 6.625,4.375 0.479,0.365 10 false Motor 6.156,4.406 6.677,4.75 0.521,0.344 10 false Heater 6.156,4.823 6.865,5.229 0.708,0.406 10 false Solenoid

Conceptual Drawing for CAN or AVC-LAN Communication
Y195595E01
1.958,1.698 2.385,2.167 0.427,0.469 10 false ECU 4.885,1.719 5.292,2.104 0.406,0.385 10 false ECU 3.125,1.948 4.417,2.323 1.292,0.375 10 false Twisted-pair Wire 2.865,2.927 4.594,3.323 1.729,0.396 10 false Differential Voltage Drive 2.469,1.479 2.677,1.688 0.208,0.208 10 false + 4.604,1.49 4.781,1.719 0.177,0.229 10 false + 4.625,1.917 4.813,2.146 0.188,0.229 10 false - 2.479,1.917 2.667,2.146 0.188,0.229 10 false -