Home › General › ENGINE › 3UR-FE ENGINE
NM27M0U _V1 General _050231 ENGINE _0241757 3UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FE ENGINE  GENERAL/CONTROL/DETAILS  LUBRICATION SYSTEM  


General


a.

The lubrication circuit is fully pressurized and oil passes through an oil filter.


b.

A cycloid rotor type oil pump is used.


c.

An oil filter with a replaceable element is used.


d.

A water-cooled type engine oil cooler is used for the towing package.

W131370C01
3.438,1 3.156,0.396 true 3.01,3.031 1.406,2.271 true 2.719,3.76 1.573,3.896 true 3.396,4.469 3.177,4.229 true 4.417,4.333 4.021,3.917 true 5.198,0.583 4.167,2.115 true 4.385,2.354 5.552,3.271 true 6.104,1.563 5.375,1.583 true 3.031,0.188 3.344,0.344 0.313,0.156 10 false *1 1.229,2.115 1.542,2.271 0.313,0.156 10 false *2 1.375,3.854 1.688,4.01 0.313,0.156 10 false *3 3.396,4.448 3.958,4.635 0.563,0.188 10 false *4 (*A) 4.448,4.396 4.76,4.552 0.313,0.156 10 false *5 5.25,0.396 5.563,0.552 0.313,0.156 10 false *6 5.594,3.292 5.906,3.448 0.313,0.156 10 false *6 6.156,1.479 6.469,1.635 0.313,0.156 10 false *1
*A Only for Models with Towing Package - -
*1 Oil Delivery Pipe (Cylinder Head Cover) *2 Oil Pump
*3 Oil Filter *4 Oil Cooler
*5 Oil Strainer *6 Camshaft Timing Oil Control Valve


Oil Circuit
W128388E06
0.979,5.167 0.979,4.906 0.979,4.906 1.115,4.906 true 3.156,0.427 4.26,0.781 1.104,0.354 10 false Main Oil Hole 1.063,1.229 1.469,1.833 0.406,0.604 10 false Chain Jet 1.656,1.198 2.635,1.5 0.979,0.302 10 false Cylinder Block 2.844,1.177 4.531,1.49 1.688,0.313 9 false Cylinder Head (For Left Bank) 4.74,1.177 6.646,1.521 1.906,0.344 9 false Cylinder Head (For Right Bank) 0.427,1.969 0.833,2.573 0.406,0.604 10 false Oil Filter 1.625,1.969 2.094,2.688 0.469,0.719 7 false Crankshaft Journals 2.188,1.958 2.708,2.708 0.521,0.75 7 false Chain Tensioner (Primary) 2.813,1.969 3.323,2.688 0.51,0.719 8 false Camshaft Timing OCV*2 3.438,1.979 3.938,2.698 0.5,0.719 8 false Intake Camshaft Journals 4.656,1.969 5.146,2.708 0.49,0.74 8 false Camshaft Timing OCV*2 5.281,1.969 5.771,2.708 0.49,0.74 8 false Intake Camshaft Journals 6.219,1.969 6.708,2.708 0.49,0.74 7 false Chain Tensioner (Primary) 5.615,3.135 6.094,3.885 0.479,0.75 7 false Exhaust Camshaft Journals 4.635,3.125 5.167,3.875 0.531,0.75 8 false VVT-i Controller 3.74,3.135 4.25,3.875 0.51,0.74 7 false Exhaust Camshaft Journals 2.823,3.156 3.323,3.844 0.5,0.688 8 false VVT-i Controller 1.615,3.146 2.083,3.813 0.469,0.667 7 false Crankshaft Pins 0.396,3.135 0.896,3.76 0.5,0.625 10 false Oil Cooler*1 1.604,4.292 2.104,5 0.5,0.708 7 false Connecting Rods 2.531,4.302 2.938,4.906 0.406,0.604 10 false Oil Jets 3.125,4.302 3.667,5.031 0.542,0.729 7 false Chain Tensioner (Secondary) 4.083,4.281 4.552,5 0.469,0.719 7 false Valve Lash Adjusters 4.948,4.271 5.51,5.021 0.563,0.75 7 false Chain Tensioner (Secondary) 5.927,4.292 6.427,5.01 0.5,0.719 8 false Lash Adjusters 0.229,6.521 2.823,6.813 2.594,0.292 10 false *1: Only for models with towing package 0.427,4.323 0.833,4.927 0.406,0.604 10 false Oil Pump 0.729,5.188 1.104,5.75 0.375,0.563 8 false Relief Valve 3.396,6.073 3.969,6.354 0.573,0.281 10 false Oil Pan 3.323,6.521 4.594,6.813 1.271,0.292 10 false *2: Oil Control Valve



Oil Pump


a.

A compact cycloid rotor type oil pump directly driven by the crankshaft is used.


b.

This oil pump uses an internal relief method which circulates relief oil to the suction passage in the oil pump. This aims to minimize oil level change in the oil pan, reduce friction, and reduce the air mixing rate in the oil.

W128389C01
1.333,1.979 1.333,1.01 true 2.927,1.781 2.469,1.354 true 2.625,3.146 2.625,2.51 true 3.604,2.896 3.458,2.125 true 5.979,1.875 6.083,1.271 true 5.729,3.479 5.792,2.854 true 1.271,0.833 1.531,1.073 0.26,0.24 10 false *1 2.313,1.219 2.573,1.458 0.26,0.24 10 false *2 2.563,3.188 2.823,3.427 0.26,0.24 10 false *3 3.573,2.927 3.833,3.167 0.26,0.24 10 false *4 6.031,1.104 6.292,1.344 0.26,0.24 10 false *a 5.01,3.354 5.271,3.594 0.26,0.24 10 false *b 5.656,3.5 5.917,3.74 0.26,0.24 10 false *c 6.198,3.354 6.458,3.594 0.26,0.24 10 false *d
*1 Timing Chain Cover *2 Oil Pump Cover
*3 Oil Pump Rotor (Cycloid Rotor) *4 Crankshaft
*a To Cylinder Block *b Oil Filter
*c Relief Oil *d From Oil Strainer




Oil Jet


a.

Four oil jets for cooling and lubricating the pistons are provided in the cylinder block, in the center of the right and left banks.


b.

These oil jets contain a check valve to prevent oil from being fed when the oil pressure is low. This prevents the overall oil pressure in the engine from dropping.

W128390C01
2.594,1.979 2.917,2.365 true 4.865,0.688 5.323,1.115 true 1.969,1.188 1.844,0.365 1.844,0.365 2.396,1.083 true 1.115,1.406 0.938,0.542 0.938,0.542 1.542,1.302 true 0.802,0.365 1.073,0.625 0.271,0.26 10 false *1 1.698,0.198 1.969,0.458 0.271,0.26 10 false *1 2.917,2.375 3.188,2.635 0.271,0.26 10 false *2 5.292,0.531 5.563,0.792 0.271,0.26 10 false *4 4.708,0.51 4.979,0.771 0.271,0.26 10 false *3 5.323,1.906 5.594,2.167 0.271,0.26 10 false *a
*1 Oil Jet *2 Cylinder Block
*3 Check Valve *4 Oil
*a Oil Jet Cross Section - -




Oil Filter


a.

An oil filter with a replaceable element is used. The element uses high-performance filter paper to improve filtration performance. It is also burnable for environmental protection.


b.

A plastic oil filter cap is used for weight reduction.


c.

This oil filter has a structure which can drain the oil remaining in the oil filter. This prevents oil from spattering when replacing the element and allows the technician to work without touching hot oil.

W128391C01
0.844,2.438 1.229,2.167 true 1.688,3.083 2.125,3.083 true 4.396,3.302 4.396,3.083 true 5.594,3.313 5.958,3.313 true 1.833,3.615 2.271,3.615 true 1.854,4.344 2.292,4.344 true 1.615,4.833 2.052,4.833 true 1.635,5.083 2.073,5.083 true 3.5,2.521 4.01,2.521 true 3.5,2.938 4.01,2.938 true 0.677,2.438 0.927,2.677 0.25,0.24 10 false *1 2.167,3.021 2.417,3.26 0.25,0.24 10 false *2 2.292,3.542 2.542,3.781 0.25,0.24 10 false *3 2.323,4.271 2.573,4.51 0.25,0.24 10 false *4 2.094,4.76 2.344,5 0.25,0.24 10 false *3 2.104,5.01 2.354,5.25 0.25,0.24 10 false *5 4.354,3.344 4.604,3.583 0.25,0.24 10 false *5 5.417,3.24 5.667,3.479 0.25,0.24 10 false *6 5.906,2.104 6.156,2.344 0.25,0.24 10 false *b 5.042,3.781 5.292,4.021 0.25,0.24 10 false *a 3.333,2.427 3.583,2.667 0.25,0.24 10 false *2 3.344,2.854 3.594,3.094 0.25,0.24 10 false *4
*1 Oil Filter Bracket *2 Oil Filter Element
*3 O-ring *4 Oil Filter Cap
*5 Oil Filter Drain Plug *6 Drain Pipe
*a Cross Section *b When Draining Oil


HINT:
·

The oil in the oil filter can be drained by removing the drain plug and inserting the drain pipe supplied with the element into the oil filter. For details, refer to the Repair Manual.

·

The engine oil maintenance interval for a model that has an oil filter with a replaceable element is the same as that for the conventional model.





Oil Cooler*


*: Only for models with towing package


a.

To suppress the increase of oil temperature while towing, and to improve reliability, a water cooled engine oil cooler is used.


b.

This engine oil cooler uses a square shaped laminated aluminum core to achieve light weight, compact size, and high heat radiation design.

W131375C01
1.958,1.74 2.76,1.99 true 3.844,2.479 4.125,2.615 true 1.74,1.635 2.052,1.792 0.313,0.156 10 false *1 4.167,2.563 4.479,2.719 0.313,0.156 10 false *2
*1 Oil Filter Bracket *2 Oil Cooler
V100135

Engine Oil Flow
V100136

Engine Coolant Flow