Home › General › ENGINE › 3UR-FE ENGINE
NM27M0U _V1 General _050231 ENGINE _0241757 3UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FE ENGINE  GENERAL/CONTROL/DETAILS  FUEL SYSTEM  


General


a.

A fuel cut control is used to stop the fuel pump when SRS airbags deploy in a frontal or side collision.


b.

Compact 12-hole type fuel injectors are used to improve the atomization of fuel.


c.

Fuel delivery pipes, with a pulsation damper function, which are formed from stamped steel, are used.


d.

Quick connectors are used to connect the fuel lines for ease of serviceability.


e.

A multi-layer plastic fuel tank is used to address environmental concerns.


f.

A fuel drain mark is provided on the fuel tank.


g.

An ORVR (Onboard Refueling Vapor Recovery) system is used.

W131386C01
1.76,4.052 5.188,6.708 3.427,2.656 1.531,1.906 0.865,0.833 true 1.771,1.917 1.365,0.542 true 1.771,2.229 1.031,3.542 true 2.104,2.333 1.938,3.729 true 3.688,2.438 3.688,3.677 true 4.208,2.406 4.469,3.604 true 4.708,2.313 5.094,3.344 true 5.052,1.781 6.052,3.135 true 1.26,0.375 1.573,0.531 0.313,0.156 10 false *1 0.708,0.656 1.021,0.813 0.313,0.156 10 false *2 0.917,3.573 1.229,3.729 0.313,0.156 10 false *3 1.854,3.802 2.167,3.958 0.313,0.156 10 false *4 4.417,3.646 4.729,3.802 0.313,0.156 10 false *5 3.635,3.76 3.948,3.917 0.313,0.156 10 false *4 5.104,3.417 5.417,3.573 0.313,0.156 10 false *6 6.104,3.188 6.417,3.344 0.313,0.156 10 false *7 1.802,4.104 2.115,4.26 0.313,0.156 10 false *3
*1 Fuel Delivery Pipe *2 Pressure Regulator
*3 Injector *4 Quick Connector
*5 Fuel Pump Assembly
·

Fuel Filter

·

Fuel Sender Gauge


*6 Fuel Tank
*7 Charcoal Canister Assembly - -




Delivery Pipe


a.

Fuel delivery pipes formed from stamped steel are used to deliver fuel to the fuel injectors.


b.

A pulsation damper is provided on the fuel delivery pipe in the left bank. A fuel pressure regulator is installed on the right bank fuel delivery pipe.

W131975C01
1.448,0.438 1.844,0.771 true 1.771,1.094 1.115,1.448 true 3.094,1.969 2.438,2.323 true 3.938,1.646 4.146,1.406 true 1.302,0.25 1.615,0.406 0.313,0.156 10 false *1 0.917,1.438 1.229,1.594 0.313,0.156 10 false *2 4.083,1.229 4.396,1.385 0.313,0.156 10 false *3 2.25,2.344 2.563,2.5 0.313,0.156 10 false *2
*1 Fuel Pressure Regulator *2 Fuel Delivery Pipe
*3 Pulsation Damper - -




Fuel Tank


a.

The multi-layer plastic fuel tank consists of six layers of four types of materials, and one of those is a recyclable material to address environmental concerns.

Cross Section of Fuel Tank
W131387C01
1.854,0.719 2.417,0.802 true 1.854,1.125 2.417,0.969 true 4.729,1.25 5.167,1.531 true 4.76,1.146 5.208,1.146 true 4.771,0.896 5.219,0.813 true 4.75,0.604 5.167,0.427 true 1.625,0.615 1.938,0.771 0.313,0.156 10 false *1 5.198,1.542 5.51,1.698 0.313,0.156 10 false *2 5.26,1.073 5.573,1.229 0.313,0.156 10 false *3 1.635,1.042 1.948,1.198 0.313,0.156 10 false *1 5.292,0.719 5.604,0.875 0.313,0.156 10 false *4 5.219,0.333 5.531,0.49 0.313,0.156 10 false *2 3.5,0.292 3.813,0.448 0.313,0.156 10 false *a 3.5,1.323 3.813,1.479 0.313,0.156 10 false *b
*1 Adhesive *2 High Density Polyethylene
*3 Recyclable Material *4 Ethylene Vinyl Alcohol Copolymer
*a Interior of Fuel Tank *b Exterior of Fuel Tank


HINT:

A fuel drain mark has been provided at the fuel tank. When dismantling (scrapping) the vehicle, drain the fuel by making a hole at this mark.

W131388C01
5.229,1.833 4.198,1.542 true 5.25,1.781 5.563,1.938 0.313,0.156 10 false *a
*a Fuel Drain Mark - -