Home › General › ENGINE › 3UR-FE ENGINE
NM27M0U _V1 General _050231 ENGINE _0241757 3UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FE ENGINE  GENERAL/CONTROL/DETAILS  ENGINE CONTROL SYSTEM  


General


a.

The engine control system of the 3UR-FE engine has the following features. The ECM that controls this system is made by DENSO.

System Outline
Sequential Multiport Fuel Injection (SFI) An L-type SFI system detects the intake air volume with a hot-wire type mass air flow meter.
Electronic Spark Advance (ESA)
·

This ECM determines the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signal to the igniters.

·

The ECM corrects ignition timing in response to engine knocking.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle conditions.
Dual Variable Valve Timing-intelligent (VVT-i) Controls the intake and exhaust camshafts to an optimal valve timing in accordance with the engine operating conditions.
Acoustic Control Induction System (ACIS) The intake air passages are switched based on engine speed and throttle valve opening angle to provide high performance in all engine speed ranges.
Fuel Pump Control
·

Based on signals from the ECM, the Fuel Pump ECU controls the fuel pump to 3 stages.

·

The fuel pump is stopped when the SRS airbag is deployed in a frontal, side, or side rear collision.


Air Injection Control The ECM controls the air injection time based on the signals from the crankshaft position sensor, engine coolant temp. sensor, mass air flow meter and air pressure sensor.
Cranking Hold Function (Starter Control) Once the ignition switch is turned to the START position, this control operates the starter until the engine starts.
Air Fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
Evaporative Emission Control
·

The ECM controls the purge flow of evaporative emission (HC) in the charcoal canister assembly in accordance with engine conditions.

·

Approximately five hours after the ignition switch has been turned OFF, the ECM operates the canister pump module to detect any evaporative emission leakage occurring between the fuel tank and the charcoal canister assembly. The ECM can detect leaks by monitoring for changes in the fuel tank pressure.


Air Conditioning Cut-off Control By turning the air conditioning compressor ON or OFF in accordance with the engine condition, drivability is maintained.
Engine Immobilizer Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid ignition key.
Brake Override System The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual.)
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and memorizes information related to the fault.
Fail-Safe When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory.



Construction


a.

The configuration of the engine control system is as shown in the following chart.

W132008E01
5.635,0.094 6.01,0.427 0.375,0.333 10 false SFI 5.385,0.583 6.49,0.927 1.104,0.344 10 false No. 1 Injector 5.385,0.979 6.406,1.333 1.021,0.354 10 false No. 2 Injector 5.375,1.375 6.51,1.719 1.135,0.344 10 false No. 3 Injector 5.396,1.771 6.438,2.125 1.042,0.354 10 false No. 4 Injector 5.385,2.177 6.417,2.531 1.031,0.354 10 false No. 5 Injector 5.365,2.563 6.396,2.927 1.031,0.365 10 false No. 6 Injector 5.365,2.958 6.417,3.333 1.052,0.375 10 false No. 7 Injector 3.333,3.49 3.771,3.927 0.438,0.438 10 false ECM 0.708,0.083 2.24,0.427 1.531,0.344 10 false Mass Air Flow Meter 0.448,0.729 2.396,1.073 1.948,0.344 10 false Intake Air Temperature Sensor 0.521,1.365 2.375,1.729 1.854,0.365 10 false Crankshaft Position Sensor 0.823,2.646 2.24,3.406 1.417,0.76 10 false Engine Coolant Temperature Sensor 0.813,3.688 1.99,4.438 1.177,0.75 10 false Accelerator Pedal Position Sensor 0.531,2.01 2.375,2.365 1.844,0.354 10 false Camshaft Position Sensor 0.646,4.729 2.302,5.083 1.656,0.354 10 false Throttle Position Sensor 0.875,5.833 2.083,6.177 1.208,0.344 10 false Bank 1, Sensor 1 0.917,5.375 2.073,5.708 1.156,0.333 10 false Knock Sensors 0.885,6.229 2.125,6.594 1.24,0.365 10 false Bank 1, Sensor 2 0.865,7.031 2.177,7.375 1.313,0.344 10 false Bank 2, Sensor 2 0.875,6.625 2.167,6.969 1.292,0.344 10 false Bank 2, Sensor 1 0.719,7.719 2.198,8.063 1.479,0.344 10 false Intake VVT Sensors 0.688,8.365 2.229,8.708 1.542,0.344 10 false Exhaust VVT Sensors 5.604,3.938 6.01,4.271 0.406,0.333 10 false ESA 5.073,4.427 6.677,4.771 1.604,0.344 10 false Ignition Coil with Igniter 5.823,7.198 6.802,7.542 0.979,0.344 10 false No. 1, 4, 6, 7 5.375,6.01 6.406,6.365 1.031,0.354 10 false No. 2, 3, 5, 8 4.833,6.813 5.708,7.156 0.875,0.344 10 false Spark Plugs 5.563,7.781 6.365,8.115 0.802,0.333 10 false ETCS-i 5.125,8.271 6.698,8.615 1.573,0.344 10 false Throttle Control Motor 5.333,3.354 6.385,3.708 1.052,0.354 10 false No. 8 Injector 5.063,5.615 6.667,5.958 1.604,0.344 10 false Ignition Coil with Igniter 4.813,7.198 5.74,7.531 0.927,0.333 10 false No. 2, 3, 5, 8 5.396,4.833 6.417,5.167 1.021,0.333 10 false No. 1, 4, 6, 7 5.896,6.813 6.781,7.156 0.885,0.344 10 false Spark Plugs

W132009E01
3.292,4.115 3.75,4.531 0.458,0.417 10 false ECM 0.781,0.26 2.104,0.615 1.323,0.354 10 false Stop Light Switch 0.615,1.052 2.156,1.802 1.542,0.75 10 false Transfer Neutral Position Switch* 0.792,2.24 2.188,2.573 1.396,0.333 10 false 4WD Control ECU* 0.479,3.031 2.417,3.385 1.938,0.354 10 false Air Pressure Sensor (Bank 1) 0.49,3.823 2.406,4.167 1.917,0.344 10 false Air Pressure Sensor (Bank 2) 0.594,4.604 2.292,4.958 1.698,0.354 10 false Airbag Sensor Assembly 0.938,5.406 2.104,5.75 1.167,0.344 10 false Ignition Switch 0.875,5.813 2.042,6.146 1.167,0.333 10 false - Starter Signal 5.396,0.146 6.458,0.49 1.063,0.344 10 false VVT-i (Intake) 5.333,2.49 6.531,2.844 1.198,0.354 10 false VVT-i (Exhaust) 5.042,2.958 6.531,3.719 1.49,0.76 10 false Camshaft Timing Oil Control Valve (Bank 1) 5.031,3.823 6.531,4.563 1.5,0.74 10 false Camshaft Timing Oil Control Valve (Bank 2) 5.604,4.844 6.146,5.198 0.542,0.354 10 false ACIS 5.625,5.333 6.073,5.688 0.448,0.354 10 false VSV 5.177,6 6.51,6.344 1.333,0.344 10 false Fuel Pump Control 5.031,6.49 6.563,6.854 1.531,0.365 10 false Circuit Opening Relay 5.198,7.094 6.573,7.448 1.375,0.354 10 false Fuel Pump Relay 5.458,7.708 6.406,8.052 0.948,0.344 10 false Fuel Pump 0.479,6.979 2.354,7.354 1.875,0.375 10 false Park/Neutral Position Switch 0.51,7.406 2.042,7.771 1.531,0.365 10 false - Neutral Start Signal 2.448,4.917 3.01,5.729 0.563,0.813 10 false CAN (V Bus) 0.885,6.167 2.021,6.531 1.135,0.365 10 false - Ignition Signal 0.5,7.781 2.344,8.115 1.844,0.333 10 false - Shift Lever Position Signal 0.448,8.208 1.781,8.604 1.333,0.396 10 false *: 4WD models 5.063,0.604 6.49,1.375 1.427,0.771 10 false Camshaft Timing Oil Control Valve (Bank 1) 5.063,1.479 6.552,2.219 1.49,0.74 10 false Camshaft Timing Oil Control Valve (Bank 2)

W132010E01
3.323,3.833 3.781,4.25 0.458,0.417 10 false ECM 0.49,0.417 2.385,0.885 1.896,0.469 10 false Transmission Control Switch 0.688,1.854 2.281,2.208 1.594,0.354 10 false Air Fuel Ratio Sensor 0.802,2.354 2.115,2.719 1.313,0.365 10 false Bank 1, Sensor 1 0.813,2.75 2.083,3.104 1.271,0.354 10 false Bank 2, Sensor 1 5.188,0.302 6.667,0.656 1.479,0.354 10 false Air Injection Control 4.969,0.865 6.594,1.615 1.625,0.75 10 false Air Injection Control Driver (Bank 1) 4.906,1.948 6.521,2.677 1.615,0.729 10 false Air Injection Control Valve (Bank 1) 4.906,2.927 6.708,3.271 1.802,0.344 10 false Electric Air Pump (Bank 1) 5.229,3.5 6.427,3.844 1.198,0.344 10 false Heater (Bank 1) 5.281,4.354 6.323,4.698 1.042,0.344 10 false AI HTR Relay 5.24,5.208 6.385,5.552 1.146,0.344 10 false Heater (Bank 2) 4.969,5.813 6.573,6.563 1.604,0.75 10 false Air Injection Control Driver (Bank 2) 4.948,6.896 6.542,7.635 1.594,0.74 10 false Air Injection Control Valve (Bank 2) 4.865,7.885 6.677,8.219 1.813,0.333 10 false Electric Air Pump (Bank 2) 0.615,8 2.281,8.385 1.667,0.385 10 false Canister Pressure Sensor 0.646,7.667 2.229,7.938 1.583,0.271 10 false Canister Pump Module 0.552,6.146 2.24,6.854 1.688,0.708 10 false TOW/HAUL Pattern Select Switch* 0.792,4.885 2.094,5.25 1.302,0.365 10 false Bank 2, Sensor 2 0.802,4.49 2.031,4.844 1.229,0.354 10 false Bank 1, Sensor 2 0.688,3.99 2.302,4.333 1.615,0.344 10 false Heated Oxygen Sensor 0.115,8.458 2.969,8.813 2.854,0.354 10 false *: Only for models with the towing package

W132011E01
3.354,4.083 3.844,4.625 0.49,0.542 10 false ECM 2.438,4.771 3.01,5.542 0.573,0.771 10 false CAN (V Bus) 1.177,4.417 1.813,4.74 0.635,0.323 10 false DLC3 5.229,4.052 6.552,4.396 1.323,0.344 10 false Bank 2, Sensor 1 4.792,4.448 6.844,4.792 2.052,0.344 10 false Heated Oxygen Sensor Heater 5.219,4.865 6.563,5.198 1.344,0.333 10 false Bank 1, Sensor 2 5.219,5.26 6.604,5.625 1.385,0.365 10 false Bank 2, Sensor 2 5.219,3.656 6.552,4.021 1.333,0.365 10 false Bank 1, Sensor 1 4.813,3.323 6.792,3.625 1.979,0.302 10 false Air Fuel Ratio Sensor Heater 4.729,2.531 6.823,3.292 2.094,0.76 10 false Air Fuel Ratio Sensor and Heated Oxygen Sensor Heater Control 5.354,1.75 6.542,2.094 1.188,0.344 10 false Starter Relay 4.844,1.146 6.75,1.479 1.906,0.333 10 false Park/Neutral Position Switch 5.323,0.677 6.615,1.031 1.292,0.354 10 false ACC CUT Relay 5.385,0.219 6.469,0.573 1.083,0.354 10 false Starter Control 0.677,3.469 2.333,3.813 1.656,0.344 10 false Transponder Key ECU 0.677,2.51 2.354,2.875 1.677,0.365 10 false Air Conditioning Amplifier 0.729,1.177 1.948,1.917 1.219,0.74 10 false Power Steering Oil Pressure Sensor 1.01,0.219 1.865,0.542 0.854,0.323 10 false Generator 1.146,5.365 1.927,5.719 0.781,0.354 10 false Battery 0.74,6.323 2.313,6.656 1.573,0.333 10 false Combination Meter 1.292,6.833 1.938,7.188 0.646,0.354 10 false MIL 0.74,7.302 2.26,7.677 1.521,0.375 10 false Vehicle Speed Signal 0.875,8.365 2.146,8.719 1.271,0.354 10 false EFI Main Relay 4.875,6.177 6.844,6.521 1.969,0.344 10 false Evaporative Emission Control 5.125,6.708 6.708,7.094 1.583,0.385 10 false Canister Pump Module 5.115,7.198 6.656,7.542 1.542,0.344 10 false Leak Detection Pump 5.406,7.594 6.375,7.917 0.969,0.323 10 false Vent Valve 5.396,8.24 6.375,8.594 0.979,0.354 10 false Purge VSV



Engine Control System Diagram


W131394C01
0.396,0.354 0.51,0.24 true 3.938,1.219 4.01,1 true 5.896,1.26 5.792,1.115 true 5.635,3.24 5.021,3.813 true 2.49,3.625 2.135,3.021 true 2.229,3.792 2.125,3.656 true 2.177,3.896 1.594,3.656 true 2.885,5.083 3.052,4.51 true 4.74,3.646 4.792,3.354 true 5.01,3.667 5.167,3.271 true 5.479,3.854 5.042,3.906 true 5.875,3.958 5.26,4.073 true 4.24,5.052 4.146,4.542 true 5.594,9.021 5.146,8.74 true 5.115,9.031 4.979,8.813 true 5.865,2.896 5.667,2.583 true 0.26,0.021 0.573,0.177 0.313,0.156 10 false *1 0.531,0.104 0.844,0.26 0.313,0.156 10 false *2 2.469,0.365 2.781,0.521 0.313,0.156 10 false *3 2.094,1.135 2.406,1.292 0.313,0.156 10 false *4 2.396,1.156 2.708,1.313 0.313,0.156 10 false *5 3.458,0.458 3.771,0.615 0.313,0.156 10 false *6 3.833,1.229 4.146,1.385 0.313,0.156 10 false *7 5.979,0.344 6.292,0.5 0.313,0.156 10 false *8 6.021,0.802 6.333,0.958 0.313,0.156 10 false *9 5.896,1.271 6.365,1.427 0.469,0.156 10 false *10 5.458,1.396 5.927,1.552 0.469,0.156 10 false *11 5.198,1.531 5.667,1.688 0.469,0.156 10 false *12 3.083,1.802 3.552,1.958 0.469,0.156 10 false *13 3.219,2.167 3.688,2.323 0.469,0.156 10 false *14 4.042,1.76 4.51,1.917 0.469,0.156 10 false *15 2.479,2.177 2.948,2.333 0.469,0.156 10 false *16 1.302,2.5 1.771,2.656 0.469,0.156 10 false *17 2.385,2.813 2.854,2.969 0.469,0.156 10 false *18 2.948,2.844 3.417,3 0.469,0.156 10 false *19 3.26,2.521 3.729,2.677 0.469,0.156 10 false *20 4.271,2.302 4.74,2.458 0.469,0.156 10 false *21 4.75,2.167 5.219,2.323 0.469,0.156 10 false *22 4.844,2.813 5.313,2.969 0.469,0.156 10 false *23 5.406,2.823 5.875,2.979 0.469,0.156 10 false *24 5.906,2.51 6.375,2.667 0.469,0.156 10 false *25 1.323,2.854 1.792,3.01 0.469,0.156 10 false *26 2.5,3.344 2.969,3.5 0.469,0.156 10 false *27 1.99,2.844 2.458,3 0.469,0.156 10 false *28 1.917,3.479 2.313,3.656 0.396,0.177 10 false *29 1.354,3.521 1.823,3.677 0.469,0.156 10 false *30 1.573,3.917 2.042,4.073 0.469,0.156 10 false *31 2.365,4.094 2.833,4.25 0.469,0.156 10 false *32 2.021,4.833 2.49,4.99 0.469,0.156 10 false *33 2.01,5.292 2.479,5.448 0.469,0.156 10 false *34 2.708,5.115 3.177,5.271 0.469,0.156 10 false *35 3.188,4.229 3.656,4.385 0.469,0.156 10 false *36 4.719,3.188 5.188,3.344 0.469,0.156 10 false *37 5.052,3.125 5.521,3.281 0.469,0.156 10 false *38 5.625,3.115 6.094,3.271 0.469,0.156 10 false *39 5.521,3.792 5.823,4.01 0.302,0.219 10 false *40 5.885,3.875 6.354,4.031 0.469,0.156 10 false *41 5.021,4.844 5.49,5 0.469,0.156 10 false *42 5.063,5.313 5.531,5.469 0.469,0.156 10 false *43 4.177,5.083 4.646,5.24 0.469,0.156 10 false *44 3.75,5.479 4.219,5.635 0.469,0.156 10 false *45 3.854,7.885 4.323,8.042 0.469,0.156 10 false *46 1.354,8.438 1.823,8.594 0.469,0.156 10 false *47 2.313,8.25 2.781,8.406 0.469,0.156 10 false *48 2.646,8.552 3.115,8.708 0.469,0.156 10 false *49 5.927,2.896 6.396,3.052 0.469,0.156 10 false *20 4.281,3.417 4.75,3.573 0.469,0.156 10 false *27 4.677,4.104 5.146,4.26 0.469,0.156 10 false *32 2.656,8.948 3.125,9.104 0.469,0.156 10 false *50 2.969,9.219 3.438,9.375 0.469,0.156 10 false *51 2.969,9.427 3.438,9.583 0.469,0.156 10 false *52 2.969,9.646 3.438,9.802 0.469,0.156 10 false *53 5.01,7.656 5.479,7.813 0.469,0.156 10 false *54 5.292,7.844 5.76,8 0.469,0.156 10 false *55 4.625,7.969 5.094,8.125 0.469,0.156 10 false *56 5.979,8.406 6.448,8.563 0.469,0.156 10 false *57 5.635,9.01 6.104,9.167 0.469,0.156 10 false *58 5.063,9.042 5.531,9.198 0.469,0.156 10 false *59 4.698,9.177 5.167,9.333 0.469,0.156 10 false *60
*1 Ignition Switch *2 Circuit Opening Relay
*3 Fuel Pump ECU *4 Intake Air Temp. Sensor
*5 Mass Air Flow Meter *6 Fuel Filter
*7 Fuel Pump *8 Vent Valve
*9 Canister Pump Module *10 Charcoal Canister Assembly
*11 Canister Pressure Sensor (For EVAP) *12 Purge VSV
*13 Throttle Position Sensor *14 Throttle Control Motor
*15 Accelerator Pedal Position Sensor *16 Air Pressure Sensor (Bank 2)
*17 Air Injection Control Driver (Bank 2) *18 Air Injection Control Valve (Bank 2)
*19 Electric Air Pump (Bank 2) *20 Heater (for Air Injection Control)
*21 VSV (For ACIS) *22 Air Pressure Sensor (Bank 1)
*23 Air Injection Control Valve (Bank 1) *24 Electric Air Pump (Bank 1)
*25 Air Injection Control Driver (Bank 1) *26 AI HTR Relay
*27 Injector *28 Intake Camshaft Timing Oil Control Valve (Bank 2)
*29 Intake VVT Sensor RH *30 Exhaust Camshaft Timing Oil Control Valve (Bank 2)
*31 Exhaust VVT Sensor RH *32 Ignition Coil with Igniter
*33 Air Fuel Ratio Sensor (Bank 2, Sensor 1) *34 Oxygen Sensor (Bank 2, Sensor 2)
*35 Knock Sensor 1, 2 (Bank 2) *36 Engine Coolant Temp. Sensor
*37 Intake Camshaft Timing Oil Control Valve (Bank 1) *38 Camshaft Position Sensor
*39 Intake VVT Sensor LH *40 Exhaust Camshaft Timing Oil Control Valve (Bank 1)
*41 Intake VVT Sensor RH *42 Air Fuel Ratio Sensor (Bank 1, Sensor 1)
*43 Oxygen Sensor (Bank 1, Sensor 2) *44 Knock Sensor 1, 2 (Bank 1)
*45 Crankshaft Position Sensor *46 ECM
*47 Battery *48 Combination Meter
·

Vehicle Speed Signal

·

MIL


*49 Airbag Sensor Assembly *50 DLC3
*51 Generator *52 Stop Light Switch
*53 TOW/HAUL Pattern Select Switch *54 A/C Amplifier
*55 ACC Cut Relay *56 Starter Relay
*57 Starter *58 Park/Neutral Position Switch
*59 Transmission Solenoid Valves *60 Transponder Key ECU
V100159

CAN (V Bus) - -



Layout of Main Components


W131395C01
1.198,1.688 0.958,0.76 true 0.229,2.74 1.24,1.917 true 1.448,3.531 1.927,2.25 true 2.844,3.531 2.281,2.375 true 3.469,3.563 2.833,2.51 true 4.615,3.188 4.156,2.313 true 5.438,2.979 4.979,2.156 true 6.021,2.813 4.76,1.75 true 6.229,2.51 5,1.729 true 2.406,2.167 2.823,0.208 true 0.854,0.583 1.167,0.74 0.313,0.156 10 false *1 0.052,2.74 0.365,2.896 0.313,0.156 10 false *2 1.333,3.563 1.646,3.719 0.313,0.156 10 false *3 2.844,3.604 3.156,3.76 0.313,0.156 10 false *4 4.604,3.188 4.917,3.344 0.313,0.156 10 false *6 5.417,3.052 5.729,3.208 0.313,0.156 10 false *7 6.042,2.875 6.354,3.031 0.313,0.156 10 false *8 6.323,2.521 6.635,2.677 0.313,0.156 10 false *9 2.708,0.031 3.177,0.188 0.469,0.156 10 false *10 3.458,3.583 3.771,3.74 0.313,0.156 10 false *5
*1 Mass Air Flow Meter
·

Intake Air Temp. Sensor


*2 Throttle Body
·

Throttle Position Sensor

·

Throttle Control Motor


*3 Air Fuel Ratio Sensor (Bank 2, Sensor 1) *4 Air Fuel Ratio Sensor (Bank 1, Sensor 1)
*5 Heated Oxygen Sensor (Bank 1, Sensor 2) *6 Fuel Pump
*7 Fuel Pump ECU *8 Canister Pump Module
·

Leak Detection Pump

·

Canister Pressure Sensor

·

Vent Valve


*9 Charcoal Canister Assembly *10 Heated Oxygen Sensor (Bank 2, Sensor 2)


W131396C01
2.021,0.958 2.438,0.542 true 1.01,3.833 0.708,3.302 true 3.51,4.5 2.792,3.146 true 2.49,0.406 2.802,0.563 0.313,0.156 10 false *1 0.563,3.094 0.875,3.25 0.313,0.156 10 false *2 3.542,4.448 3.854,4.604 0.313,0.156 10 false *3
*1 Malfunction Indicator Lamp *2 Accelerator Pedal Position Sensor
*3 DLC3 - -


W131397C01
2.229,0.854 1.781,0.271 true 1.594,0.719 1.063,0.354 true 1.448,1.448 0.604,1.615 true 1.594,1.458 1.021,2.313 true 2.948,0.906 3.583,0.542 true 2.344,0.823 2.802,0.26 true 5.563,0.917 5.219,0.323 true 5.063,1.979 5.625,1.063 true 6,0.719 6.229,0.26 true 4.49,0.698 4.323,0.385 true 1.635,0.073 1.948,0.229 0.313,0.156 10 false *1 0.813,0.24 1.125,0.396 0.313,0.156 10 false *2 0.417,1.583 0.729,1.74 0.313,0.156 10 false *3 0.865,2.354 1.177,2.51 0.313,0.156 10 false *4 3.656,0.385 3.969,0.542 0.313,0.156 10 false *5 2.781,0.083 3.094,0.24 0.313,0.156 10 false *6 4.208,0.198 4.521,0.354 0.313,0.156 10 false *7 5.094,0.156 5.406,0.313 0.313,0.156 10 false *8 4.969,2.021 5.281,2.177 0.313,0.156 10 false *9 6.292,0.167 6.76,0.323 0.469,0.156 10 false *10
*1 Air Injection Control Valve (Bank 2)
·

Air Pressure Sensor


*2 ECM
*3 Electric Air Pump (Bank 2) *4 Electric Air Pump (Bank 1)
*5 Air Injection Control Driver *6 Air Injection Control Valve (Bank 1)
·

Air Pressure Sensor


*7 Engine Room Relay Block *8 Starter Relay
*9 Circuit Opening Relay *10 Fuel Pump Relay


W131398C01
2.156,0.885 1.865,0.344 true 1.896,3.021 2.094,1.427 true 1.76,1.448 0.906,0.708 true 2.302,2.833 2.229,1.469 true 2.615,2.74 2.375,1.635 true 2.958,2.635 2.51,1.542 true 3.021,0.813 2.396,1.313 true 4.333,1.042 4,0.75 true 4.323,1.323 3.99,1.135 true 4.281,1.615 3.979,1.708 true 4.302,1.906 4,2.135 true 6.594,0.833 6.292,1.063 true 6.604,1.281 6.302,1.375 true 6.594,1.865 6.26,1.677 true 6.615,2.25 6.281,1.958 true 4.792,1 4.625,0.354 true 4.76,1.302 4.24,0.458 true 4.146,2.635 4.781,1.604 true 4.427,2.885 4.792,1.927 true 5.063,1.125 4.969,0.292 true 4.896,3.021 5.052,1.792 true 5.719,3.094 5.573,1.896 true 6.135,2.969 5.833,1.948 true 6.354,2.74 5.833,1.677 true 5.771,1.031 5.917,0.385 true 5.813,1.375 6.292,0.49 true 5.552,1.167 5.615,0.302 true 3.635,4.073 3.333,3.531 true 3.25,4.427 2.646,4.031 true 5.281,5.5 4.698,4.813 true 2.969,6.104 3.344,5.74 true 5.49,4.958 4.969,4.594 true 5.365,4.167 4.854,4.438 true 4.792,3.76 4.51,4.49 true 1.708,0.146 2.021,0.302 0.313,0.156 10 false *1 0.76,0.563 1.073,0.719 0.313,0.156 10 false *2 1.833,3.063 2.146,3.219 0.313,0.156 10 false *3 2.26,2.906 2.573,3.063 0.313,0.156 10 false *4 2.625,2.781 2.938,2.938 0.313,0.156 10 false *5 2.958,2.656 3.271,2.813 0.313,0.156 10 false *6 3.063,0.708 3.375,0.865 0.313,0.156 10 false *7 4,2.656 4.313,2.813 0.313,0.156 10 false *9 3.74,0.615 4.208,0.771 0.469,0.156 10 false *10 4.885,0.094 5.198,0.25 0.313,0.156 10 false *8 4.094,0.25 4.406,0.406 0.313,0.156 10 false *9 4.542,0.135 4.854,0.292 0.313,0.156 10 false *9 4.354,2.948 4.667,3.104 0.313,0.156 10 false *9 3.719,1.031 4.188,1.188 0.469,0.156 10 false *10 3.698,1.656 4.167,1.813 0.469,0.156 10 false *10 3.781,2.115 4.25,2.271 0.469,0.156 10 false *10 4.75,3.083 5.219,3.24 0.469,0.156 10 false *11 5.604,3.146 6.073,3.302 0.469,0.156 10 false *12 6.073,3.031 6.385,3.188 0.313,0.156 10 false *9 6.344,2.781 6.656,2.938 0.313,0.156 10 false *9 6.656,2.26 7.125,2.417 0.469,0.156 10 false *10 6.635,1.833 7.104,1.99 0.469,0.156 10 false *10 6.646,1.188 7.115,1.344 0.469,0.156 10 false *10 6.635,0.708 7.104,0.865 0.469,0.156 10 false *10 5.844,0.188 6.156,0.344 0.313,0.156 10 false *9 6.313,0.292 6.625,0.448 0.313,0.156 10 false *9 5.542,0.094 5.854,0.25 0.313,0.156 10 false *13 3.135,3.344 3.604,3.5 0.469,0.156 10 false *14 2.448,3.885 2.917,4.042 0.469,0.156 10 false *15 2.729,6.115 3.198,6.271 0.469,0.156 10 false *16 5.271,5.542 5.74,5.698 0.469,0.156 10 false *17 5.542,4.969 6.01,5.125 0.469,0.156 10 false *18 5.427,4.083 5.896,4.24 0.469,0.156 10 false *19 4.792,3.552 5.26,3.708 0.469,0.156 10 false *20
*1 Purge VSV *2 Engine Coolant Temp. Sensor
*3 Camshaft Position Sensor *4 Intake Camshaft Timing Oil Control Valve (Bank 1)
*5 Exhaust Camshaft Timing Oil Control Valve (Bank 1) *6 Exhaust VVT Sensor LH
*7 Intake VVT Sensor LH *8 Knock Sensor 2 (Bank 2)
*9 Injector *10 Ignition Coil with Igniter
*11 Knock Sensor 1 (Bank 2) *12 Knock Sensor 1 (Bank 1)
*13 Knock Sensor 2 (Bank 1) *14 VSV (For ACIS)
*15 ACIS Actuator *16 Crankshaft Position Sensor
*17 Exhaust VVT Sensor RH *18 Exhaust Camshaft Timing Oil Control Valve (Bank 2)
*19 Intake Camshaft Timing Oil Control Valve (Bank 2) *20 Intake VVT Sensor RH



Main Components of Engine Control System


a.

General

i.

The main components of the 3UR-FE engine control system are as follows:

Components Outline Quantity
ECM (Supplier) 32-bit CPU (DENSO) 1
Mass Air Flow Meter (Built-in Intake Air Temperature Sensor) Hot-wire Type (Slot-in) 1
Crankshaft Position Sensor (Rotor Teeth) Magnetic Resistance Element (MRE) Type (36-2) 1
Camshaft Position Sensor (Rotor Teeth) Magnetic Resistance Element (MRE) Type (3) 1
Intake VVT Sensor (Rotor Teeth) Magnetic Resistance Element (MRE) Type (3) 2 (1 each bank)
Exhaust VVT Sensor (Rotor Teeth) Magnetic Resistance Element (MRE) Type (3) 2 (1 each bank)
Accelerator Pedal Position Sensor Linear (Non-Contact) Type 1
Throttle Position Sensor Linear (Non-Contact) Type 1
Knock Sensor Bank 1, Sensor 1 Built-in Piezoelectric Type (Non-resonant Type/Flat Type) 4 (2 each bank)
Bank 2, Sensor 1
Bank 1, Sensor 2
Bank 2, Sensor 2
Air Fuel Ratio Sensor Bank 1, Sensor 1 Heated Type (Planar Type) 2 (1 each bank)
Bank 2, Sensor 1
Heated Oxygen Sensor Bank 1, Sensor 2 Heated Type (Cup Type) 2 (1 each bank)
Bank 2, Sensor 2
Injector 12-hole Type 8



b.

Mass Air Flow Meter

i.

This mass air flow meter, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.


ii.

This mass air flow meter has a built-in intake air temperature sensor.

W128425C03
5.115,1.906 5.594,1.604 true 5.615,1.469 5.854,1.698 0.24,0.229 10 false *1
*1 Intake Air Temperature Sensor - -
V100135

Air Flow - -




c.

Crankshaft Position Sensor, Camshaft Position Sensor and VVT Sensor

i.

General

·

Magnetic Resistance Element (MRE) sensors are used for the crankshaft position, camshaft position, and VVT sensors.

·

The timing rotor for the crankshaft position sensor is installed on the back end of the crankshaft. The timing rotor has 34 teeth, with 2 teeth missing, at 10° intervals. Based on these teeth, the crankshaft position sensor transmits crankshaft position signals (NE signal) consisting of 33 Hi/Lo output pulses every 10° per revolution of the crankshaft, and 1 Hi/Lo output pulse every 30°. The ECM uses the NE signal for detecting the crankshaft position as well as for detecting the engine speed. It uses the missing teeth signal for determining the top-dead-center.

·

The camshaft position sensor uses a timing rotor that is installed on the front end of the intake camshaft sprocket of the left bank. Based on the timing rotor, the sensor outputs camshaft position signals (G2 signal) consisting of 3 (3 Hi output, 3 Lo output) pulses for every 2 revolutions of the crankshaft. The ECM compares the G2 and NE signals to detect the camshaft position and identify the cylinder.

·

The intake and exhaust VVT sensors use timing rotors that are installed on the intake and exhaust camshafts of each bank. Based on the timing rotors, the sensors output VVT position signals consisting of 3 (3 Hi output, 3 Lo output) pulses for every 2 revolutions of the crankshaft. The ECM compares these VVT position signals to the NE signal to detect the actual valve timing.

W128432C03
1.938,0.885 1.75,0.302 true 1.365,1.76 0.938,2.615 true 5.115,0.802 5.313,0.313 true 5.792,2.573 5.333,1.865 true 3.177,4.729 2.24,4.927 true 5.292,4.302 4.125,4.135 true 1.625,0.135 1.823,0.323 0.198,0.188 10 false *1 0.823,2.615 1.021,2.802 0.198,0.188 10 false *2 5.25,0.156 5.448,0.344 0.198,0.188 10 false *3 5.771,2.573 5.969,2.76 0.198,0.188 10 false *4 2.063,4.823 2.271,5.073 0.208,0.25 10 false *5 4.073,0.448 4.333,0.698 0.26,0.25 10 false *a 5.302,4.219 5.5,4.406 0.198,0.188 10 false *2
*1 Camshaft Position Sensor *2 Timing Rotor
*3 Intake VVT Sensor *4 Exhaust VVT sensor
*5 Crankshaft Position Sensor - -
*a Bank 1 - -


Sensor Output Waveforms
W128434E02
5.656,0.354 5.344,0.354 5.344,0.354 3.396,1.083 true 1.906,0.469 4.083,0.781 2.177,0.313 10 false VVT Sensor Signal Plate (720° CA) 5.75,0.281 6.667,0.979 0.917,0.698 10 false VVT Variable Timing Range 3.938,1.188 4.521,1.542 0.583,0.354 10 false 230° CA 5.271,1.188 5.823,1.531 0.552,0.344 10 false 140° CA 2.323,1.198 2.906,1.552 0.583,0.354 10 false 230° CA 1.677,1.302 1.938,1.698 0.26,0.396 10 false 40° CA 3.302,1.302 3.563,1.698 0.26,0.396 10 false 40° CA 4.938,1.292 5.198,1.688 0.26,0.396 10 false 40° CA 1.958,2.073 4.979,2.417 3.021,0.344 10 false Camshaft Position Sensor Signal Plate (720° CA) 0.031,1.323 0.844,1.667 0.813,0.344 10 false VVT Sensor* 0.094,2.854 0.708,3.958 0.615,1.104 10 false Camshaft Position Sensor 0.135,4.375 0.75,5.479 0.615,1.104 10 false Crankshaft Position Sensor 1.865,2.917 2.125,3.313 0.26,0.396 10 false 60° CA 3.896,2.594 4.406,2.917 0.51,0.323 10 false 60° CA 3.146,3.063 3.719,3.375 0.573,0.313 10 false 180° CA 2.26,2.573 2.833,2.885 0.573,0.313 10 false 120° CA 5.281,2.594 5.854,2.906 0.573,0.313 10 false 180° CA 4.427,3.083 5,3.396 0.573,0.313 10 false 120° CA 2.063,3.865 2.635,4.177 0.573,0.313 10 false 360° CA 4.219,3.865 4.792,4.177 0.573,0.313 10 false 360° CA 1.667,4.115 2.24,4.427 0.573,0.313 10 false 10° CA 3.469,4.125 4.042,4.438 0.573,0.313 10 false 30° CA 1.073,5.438 5.917,5.781 4.844,0.344 10 false *: This is an example of an output waveform of the intake VVT sensor (Bank 1).



ii.

MRE Type Sensor

·

The MRE type sensor consists of an MRE, a magnet and a sensor.

·

The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to Hi or Lo. The ECM detects the crankshaft and camshaft position based on this output voltage.

·

The differences between the MRE type sensor and the pick-up coil type sensor used on a conventional model are as follows.

·

An MRE type sensor outputs a constant level of Hi/Lo digital signals regardless of the engine speed. Therefore, an MRE type sensor can detect the positions of the crankshaft and camshaft at an early stage of cranking.

·

A pickup coil type sensor outputs analog signals with levels that change with the engine speed.

MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W128435E01
4.719,2.375 4.385,0.844 4.385,0.844 4.771,0.844 true 4.76,1.656 4.385,0.844 false 3.625,1.26 4.063,1.938 0.438,0.677 10 false Engine Speed 0.094,1.271 0.531,1.948 0.438,0.677 10 false Engine Speed 0.073,2.542 0.51,3.219 0.438,0.677 10 false Sensor Output 3.583,2.302 4.021,2.979 0.438,0.677 10 false Sensor Output 2.667,2.083 3.104,2.76 0.438,0.677 10 false Digital Output 4.875,0.771 5.688,1.125 0.813,0.354 10 false No Detection 6.635,2.042 7.073,2.719 0.438,0.677 10 false Analog Output 1.479,3.271 2.24,3.656 0.76,0.385 10 false MRE Type 4.896,3.26 6.031,3.635 1.135,0.375 10 false Pick-up Coil Type





d.

Accelerator Pedal Position Sensor

i.

This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.


ii.

The magnetic yoke that is mounted at the base of the accelerator pedal arm moves around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


iii.

This accelerator pedal position sensor includes 2 Hall ICs and circuits for the main and sub signals. It converts the accelerator pedal depression angles into two electric signals with differing characteristics and outputs them to the ECM.

W128436E01
2.729,0.313 3.635,0.688 true 3.938,1.115 4.688,1.021 true 3.219,2.052 4.75,2.031 true 3.76,2.656 4.896,2.813 true 1.146,5.271 1.49,5.094 true 0.656,4.688 0.938,5.146 true 1.354,5.458 1.51,5.552 true 1.208,6.698 1.521,6.656 true 2.281,0.219 2.719,0.542 0.438,0.323 10 false Hall IC 4.75,0.938 5.771,1.271 1.021,0.333 10 false Sensor Housing 4.792,1.958 5.74,2.281 0.948,0.323 10 false Magnetic Yoke 4.958,2.75 6.385,3.094 1.427,0.344 10 false Accelerator Pedal Arm 3.115,5.406 3.49,5.76 0.375,0.354 10 false ECM 1.542,5.01 1.979,5.333 0.438,0.323 10 false Hall IC 0.219,4.604 0.656,4.927 0.438,0.323 10 false Hall IC 1.573,5.5 2.167,6.281 0.594,0.781 10 false Magnetic Yoke 0.417,7.042 1.563,7.688 1.146,0.646 10 false Accelerator Pedal Position Sensor 1.583,6.583 2.99,6.938 1.406,0.354 10 false Accelerator Pedal Arm 3.792,5.156 4.302,5.854 0.51,0.698 10 false Output Voltage 4.208,6.26 4.656,7.021 0.448,0.76 10 false Fully Closed 6.438,6.25 6.865,7.01 0.427,0.76 10 false Fully Open 4.938,6.292 6.073,6.969 1.135,0.677 10 false Accelerator Pedal Depressed Angle 5.573,5.552 5.885,5.875 0.313,0.323 10 false VPA 4.802,5.135 5.177,5.438 0.375,0.302 10 false VPA2 4.208,4.552 4.365,4.76 0.156,0.208 10 false V 4.229,4.76 4.323,4.938 0.094,0.177 10 false 5 4.219,5.896 4.323,6.125 0.104,0.229 10 false 0 3.302,4.354 3.594,4.5 0.292,0.146 8 false VPA 3.042,4.354 3.281,4.51 0.24,0.156 8 false EPA 2.667,4.354 3,4.51 0.333,0.156 8 false VCPA 2.51,5.667 2.844,5.823 0.333,0.156 8 false VPA2 2.542,6.219 2.854,6.396 0.313,0.177 8 false VCP2 2.552,5.938 2.854,6.115 0.302,0.177 8 false EPA2



e.

Throttle Position Sensor

i.

This non-contact type throttle position sensor is mounted on the throttle body, and it uses a Hall IC.


ii.

The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of throttle valve position signals to the ECM.


iii.

The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angle into two electrical signals that have differing characteristics and outputs them to the ECM.

W131399E01
5.75,0.76 6.115,0.198 6.115,0.198 6.354,0.198 true 5.76,0.885 6.146,0.594 6.146,0.594 6.354,0.594 true 5.76,1.01 6.125,2.24 6.125,2.24 6.344,2.24 true 1.396,3.583 1.396,3.094 1.396,3.094 1.188,3.094 true 1.333,4.698 1.333,5.094 1.333,5.094 1.125,5.094 true 1.417,3.865 2.115,2.656 2.115,2.656 2.448,2.656 true 1.427,4.438 1.896,5.552 1.896,5.552 2.24,5.552 true 6.396,0.104 6.958,0.385 0.563,0.281 10 false Magnet 6.375,0.5 7.135,1.792 0.76,1.292 10 false Hall IC (For Throttle Position Sensor) 6.396,2.177 6.958,2.458 0.563,0.281 10 false Magnet 4.573,2.198 5.479,2.573 0.906,0.375 10 false Cross Section 0.583,3.01 1.146,3.292 0.563,0.281 10 false Magnet 0.583,5 1.146,5.281 0.563,0.281 10 false Magnet 2.313,5.479 2.906,5.75 0.594,0.271 10 false Hall IC 2.51,2.552 3.104,2.823 0.594,0.271 10 false Hall IC 1.979,3.521 2.573,3.74 0.594,0.219 10 false VTA1 1.979,4.125 2.573,4.344 0.594,0.219 10 false VC 1.969,4.427 2.563,4.646 0.594,0.219 10 false VTA2 1.979,3.844 2.573,4.063 0.594,0.219 10 false E2 2.792,4.052 3.198,4.438 0.406,0.385 10 false ECM 4.146,3.115 4.552,3.5 0.406,0.385 10 false V 4.094,3.354 4.292,3.604 0.198,0.25 10 false 5 3.615,3.646 4.156,4.385 0.542,0.74 10 false Output Voltage 4.146,4.448 4.344,4.698 0.198,0.25 10 false 0 4.573,3.542 5.167,3.76 0.594,0.219 10 false VTA2 5.385,4 5.979,4.219 0.594,0.219 10 false VTA1 4.969,4.542 5.167,4.792 0.198,0.25 10 false 30 6.438,4.563 6.635,4.813 0.198,0.25 10 false 90 5.698,4.563 5.896,4.813 0.198,0.25 10 false 60 3.875,4.781 4.76,5.438 0.885,0.656 10 false Throttle Valve Fully Closed 5.958,4.771 6.844,5.427 0.885,0.656 10 false Throttle Valve Fully Open 4.438,5.479 6.26,5.823 1.823,0.344 10 false Throttle Valve Opening Angle



f.

Knock Sensor (Flat Type)

i.

General

In a conventional type knock sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

The other type of knock sensor, a flat type knock sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 6 kHz to 15 kHz).

*: The term "Knock" or "Knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous.This use of "Knock" or "Knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.


·

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock sensor, the vibration detection ability is increased compared to a conventional type knock sensor, and more precise ignition timing control is possible.

W128426E01
1.542,0.427 4.417,0.792 2.875,0.365 10 false : Resonance characteristic of conventional type 1.552,0.833 3.969,1.24 2.417,0.406 10 false : Resonance characteristic of flat type 4.74,2.854 5.042,3.083 0.302,0.229 10 false (Hz) 2.094,1.396 2.313,1.615 0.219,0.219 10 false (V) 1.75,2.031 2.25,2.448 0.5,0.417 10 false Voltage 3.24,2.865 3.906,3.188 0.667,0.323 10 false Frequency 2.708,3.26 4.635,3.604 1.927,0.344 10 false Characteristic of Knock Sensor 5.021,1.479 6.302,2.208 1.281,0.729 10 false A: Detection band of conventional type 5.052,2.229 6.365,2.917 1.313,0.688 10 false B: Detection band of flat type 3.802,2.375 3.969,2.563 0.167,0.188 10 false B 3.75,1.542 3.917,1.729 0.167,0.188 10 false A




ii.

Construction

·

A flat type knock sensor is installed to an engine by placing it over the stud installed on the cylinder block. For this reason, a hole for the stud exists in the center of the sensor.

·

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.

·

An open/short circuit detection resistor is integrated in the sensor.

W128427C01
1.188,1.354 0.708,1.01 true 1.167,1.458 0.667,1.281 true 1.146,1.542 0.781,1.74 true 2.385,1.51 2.438,0.781 true 5.448,1.292 6.146,0.885 true 5.5,1.333 6.219,1.531 true 0.625,0.396 0.927,0.667 0.302,0.271 12 false *A: 4.271,0.375 4.573,0.646 0.302,0.271 12 false *B: 0.604,1.688 0.865,1.927 0.26,0.24 11 false *3 0.49,1.156 0.75,1.396 0.26,0.24 11 false *2 0.531,0.875 0.792,1.115 0.26,0.24 11 false *1 2.375,0.604 2.635,0.844 0.26,0.24 11 false *4 6.177,0.76 6.438,1 0.26,0.24 11 false *3 6.25,1.479 6.51,1.719 0.26,0.24 11 false *5
*A Flat Type Knock Sensor (Non-resonant Type) *B Conventional Type Knock Sensor (Resonant Type)
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open/Short Circuit Detection Resistor
*5 Vibration Plate - -




iii.

Operation

The knocking vibration is transmitted to the steel weight and its inertia applies pressure to the piezoelectric element. This action generates electromotive force (voltage).

W128428C01
3.135,1.375 2.615,0.969 true 3.229,1.49 2.583,1.427 true 3.156,1.625 2.656,1.948 true 2.438,0.833 2.677,1.063 0.24,0.229 10 false *1 2.49,1.896 2.729,2.125 0.24,0.229 10 false *2 2.417,1.323 2.656,1.552 0.24,0.229 10 false *a
*1 Steel Weight *2 Piezoelectric Element
*a Inertia - -




iv.

Open/Short Circuit Detection Resistor

When the ignition is ON, the open/short circuit detection resistor in the knock sensor and the resistor in the ECM keep the voltage at the terminal KNK1 of engine constant.

An Integrated Circuit (IC) in the ECM is always monitoring the voltage of the terminal KNK1. If the open/short circuit occurs between the knock sensor and the ECM, the voltage of the terminal KNK1 will change allowing the ECM to detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W128429E01
0.844,0.854 0.271,0.854 0.271,0.854 1.094,2.271 true 1.906,2.281 2.396,3.188 2.396,3.188 2.573,3.188 true 0.896,0.802 2.292,1.146 1.396,0.344 10 false Piezoelectric Element 0.865,1.375 2.448,1.698 1.583,0.323 10 false Flat Type Knock Sensor 2.625,3.115 3.833,3.75 1.208,0.635 10 false Open/Short Circuit Detection Resistor 2.01,2.208 2.521,2.552 0.51,0.344 10 false 200 kΩ 5.135,1.042 5.542,1.375 0.406,0.333 10 false ECM 4.375,1.146 4.656,1.5 0.281,0.354 10 false 5 V 4.531,1.688 5.042,1.906 0.51,0.219 10 false 220 kΩ 6.073,1.979 6.24,2.313 0.167,0.333 10 false IC 3.75,2.615 4.177,2.802 0.427,0.188 10 false EKNK 3.771,1.781 4.156,1.969 0.385,0.188 10 false KNK1


HINT:

These knock sensors are mounted in specific directions at specific angles. To prevent the right and left bank wiring connectors from being interchanged, make sure to install each sensor in its prescribed direction. For details, refer to the Repair Manual.




g.

Air Fuel Ratio Sensor and Heated Oxygen Sensor

i.

General

·

A planar type air-fuel ratio sensor and a cup type heated oxygen sensor are used.

·

The basic construction of the oxygen sensor and the air-fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction that are used.

·

The planar type air-fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate a sensor element with a heater, thus improving the warm-up performance of the sensor.

·

The cup type heated oxygen sensor contains a sensor element that surrounds a heater.

W131400C01
0.74,0.333 3.615,3.677 2.875,3.344 3.969,0.344 6.844,3.688 2.875,3.344 2.896,2.167 2.719,1.594 true 2.823,2.219 2.479,1.792 true 2.917,2.479 2.417,2.125 true 2.771,3.354 2.969,3.042 true 3.417,3.271 3.167,3.01 true 3.156,3.344 3.01,2.74 true 3.313,2.552 3.073,2.563 true 3.229,1.656 3.052,2.125 true 6.167,2.521 6.521,2.76 true 5.708,1.573 5.833,2.063 true 5.896,2.573 5.594,3.115 true 6.094,1.583 5.948,2.052 true 6.271,2.177 6.479,1.823 true 0.781,0.375 1.125,0.594 0.344,0.219 12 false *A: 4.021,0.385 4.406,0.594 0.385,0.208 12 false *B: 2.583,1.406 2.896,1.563 0.313,0.156 10 false *1 2.313,1.625 2.625,1.781 0.313,0.156 10 false *2 2.26,1.979 2.479,2.198 0.219,0.219 10 false *3 2.635,3.385 2.948,3.542 0.313,0.156 10 false *4 3.427,3.281 3.74,3.438 0.313,0.156 10 false *5 3.365,2.479 3.677,2.635 0.313,0.156 10 false *6 3.115,3.375 3.427,3.531 0.313,0.156 10 false *3 6.094,1.406 6.406,1.563 0.313,0.156 10 false *3 5.583,1.406 5.896,1.563 0.313,0.156 10 false *3 6.542,2.771 6.854,2.927 0.313,0.156 10 false *5 5.5,3.146 5.813,3.302 0.313,0.156 10 false *4 6.49,1.667 6.802,1.823 0.313,0.156 10 false *6 3.177,1.458 3.49,1.615 0.313,0.156 10 false *2
*A Air Fuel Ratio Sensor (Planar Type) *B Heated Oxygen Sensor (Cup Type)
*1 Dilation Layer *2 Alumina
*3 Platinum Electrode *4 Sensor Element (Zirconia)
*5 Heater *6 Atmosphere




ii.

Characteristics

As illustrated below, a conventional heated oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air-fuel ratio (14.7:1). In contrast, the air-fuel ratio sensor data is approximately proportional to the existing air-fuel ratio. The air-fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air-fuel ratio has been improved. The air-fuel ratio sensor data can be viewed using a Techstream.

W131401E02
0.542,0.073 2.01,0.385 1.469,0.313 10 false : Air fuel ratio sensor 0.521,0.438 2.188,0.76 1.667,0.323 10 false : Heated oxygen sensor 0.521,1.49 2,2.646 1.479,1.156 10 false Air-Fuel Ratio Sensor Output* (Data Displayed on Techstream) 1.958,0.927 2.417,1.125 0.458,0.198 10 false (V) 2.063,1.135 2.521,1.333 0.458,0.198 10 false 4.2 2.073,2.896 2.531,3.094 0.458,0.198 10 false 2.2 2.385,3.198 3,3.49 0.615,0.292 10 false 11 (Rich) 3.406,3.208 3.865,3.406 0.458,0.198 10 false 14.7 4.469,3.219 5.083,3.51 0.615,0.292 10 false 19 (Lean) 3.135,3.438 4.063,3.719 0.927,0.281 10 false Air Fuel Ratio 4.979,0.938 5.438,1.135 0.458,0.198 10 false (V) 4.875,1.146 5.333,1.344 0.458,0.198 10 false 1 4.927,2.917 5.385,3.115 0.458,0.198 10 false 0.1 5.083,1.5 6.167,2.26 1.083,0.76 10 false Heated Oxygen Sensor Output 5.427,2.51 7.083,3.75 1.656,1.24 10 false *: This value is calculated internally in the ECM and is not an ECM terminal voltage.





Sequential Multiport Fuel Injection (SFI) System


a.

This L-type SFI system directly detects the intake air mass using a hot wire type air flow meter.


b.

An independent injection system (in which fuel is injected once into each intake port for each two revolutions of the crankshaft) is used.


c.

There are two (synchronous and non-synchronous) injections:

i.

Synchronous injection, in which injection always occurs at the same timing relative to the firing order.


ii.

The non-synchronous injection in which injection is effected regardless of the crankshaft angle.



d.

Furthermore, to protect the engine and achieve lower fuel consumption, the system uses a fuel cutoff in which the injection of fuel may be stopped temporarily in accordance with the driving conditions.


e.

Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started.

Sequential Multiport Fuel Injection
W131402E01
1.688,1.104 1.688,0.385 1.688,0.385 1.51,0.385 true 2.563,1.01 2.563,0.51 2.563,0.51 2.927,0.51 true 4.26,1.104 4.26,0.385 4.26,0.385 4.49,0.385 true 0.052,0.292 1.49,0.615 1.438,0.323 10 false Synchronous Injection 1,1.042 1.375,1.313 0.375,0.271 10 false # 10 1,1.271 1.375,1.542 0.375,0.271 10 false # 20 1,1.49 1.375,1.76 0.375,0.271 10 false # 30 1,1.708 1.375,1.979 0.375,0.271 10 false # 40 1,1.948 1.375,2.219 0.375,0.271 10 false # 50 0.99,2.167 1.365,2.438 0.375,0.271 10 false # 60 0.99,2.385 1.365,2.656 0.375,0.271 10 false # 70 0.99,2.635 1.365,2.906 0.375,0.271 10 false # 80 2.969,0.406 3.521,0.76 0.552,0.354 10 false Ignition 4.552,0.281 6.438,0.604 1.885,0.323 10 false Non-synchronous Injection



Electronic Throttle Control System-intelligent (ETCS-i)


a.

General

i.

ETCS-i uses the ECM to calculate the optimal throttle valve angle that is appropriate for the respective driving condition and uses a throttle control motor to control the angle.


ii.

The ETCS-i consists of the following five functions:

·

Normal Throttle Control (non-linear control)

·

Idle Speed Control (ISC)

·

Traction Control (TRAC), Active Traction Control (A-TRAC)* or AUTO LSD

*: Only for 4WD models


·

Vehicle Stability Control (VSC) Coordination Control

·

Cruise Control

·

TOW/HAUL Control*

*: Only for models with towing package

System Diagram
W131403E04
3.448,0.844 3.448,0.167 3.448,0.167 3.24,0.167 true 1.948,1.063 1.948,0.531 1.948,0.531 1.74,0.531 true 4.49,0.958 4.49,0.281 4.49,0.281 4.729,0.281 true 0.531,0.438 1.708,1.156 1.177,0.719 10 false Accelerator Pedal Position Sensor 2.323,0.063 3.271,0.427 0.948,0.365 10 false Throttle Valve 4.781,0.208 6.354,0.573 1.573,0.365 10 false Throttle Position Sensor 5.375,0.833 6.948,1.198 1.573,0.365 10 false Throttle Control Motor 0.635,2.49 2.167,2.833 1.531,0.344 10 false Mass Air Flow Meter 0.625,3.115 2.156,3.458 1.531,0.344 10 false Cruise Control Switch 0.281,3.74 2.292,4.094 2.01,0.354 9 false TOW/HAUL Pattern Select Switch* 0.708,4.385 2.292,4.75 1.583,0.365 10 false Junction Connector 0.833,5 2.229,5.365 1.396,0.365 10 false Skid Control ECU 2.354,4.635 2.729,5.469 0.375,0.833 10 false CAN (V Bus) 3.49,3.688 3.833,4.073 0.344,0.385 10 false ECM 5.719,3.5 6.531,3.833 0.813,0.333 10 false Ignition Coil 5.667,4.385 6.552,4.729 0.885,0.344 10 false Fuel Injector 0.24,5.438 2.885,5.792 2.646,0.354 10 false *: Only for models with towing package





b.

Normal Throttle Control (Non-linear Control)

i.

Controls the throttle to an optimal throttle valve angle that is appropriate for the driving condition based on information such as the amount of the accelerator pedal effort and the engine speed in order to realize excellent throttle control and comfort in all operating ranges.

Control examples during Acceleration and Deceleration
W131827E02
5.583,0.146 7.104,0.469 1.521,0.323 10 false : With control 5.583,0.563 6.979,0.927 1.396,0.365 10 false : Without control 0.271,0.875 1.281,1.563 1.01,0.688 10 false Vehicle's Longitudinal G 1.365,1.365 1.521,1.563 0.156,0.198 10 false 0 1.354,2.417 1.51,2.615 0.156,0.198 10 false 0 1.344,3.135 1.5,3.333 0.156,0.198 10 false 0 0.26,1.979 1.271,2.667 1.01,0.688 10 false Throttle Valve Angle 0.25,2.865 1.25,3.458 1,0.594 10 false Ignition Timing 3.104,3.281 3.49,3.552 0.385,0.271 10 false Time



c.

Idle Speed Control

i.

The ECM controls the throttle valve in order to constantly maintain an ideal idle speed.



d.

TRAC, A-TRAC* or AUTO LSD

*: Only for 4WD models


i.

As part of the TRAC, A-TRAC or AUTO LSD the throttle valve opening is reduced by a demand signal sent from the Skid Control ECU to the ECM. This demand signal will be sent if an excessive amount of slippage occurs at a drive wheel, thus facilitating vehicle stability and the application of an appropriate amount of power to the road.



e.

VSC Coordination Control

i.

In order to bring the effectiveness of the VSC system control into full play, the throttle valve angle is controlled by effecting a coordination control with the Skid Control ECU.



f.

Cruise Control

i.

The ECM directly actuates the throttle valve for operation of the cruise control.



g.

TOW/HAUL Control*

*: Only for models with towing package


i.

When tow/haul control is operating, the throttle valve opening angle relationship to the accelerator pedal angle is increased. As a result, during tow/haul control, acceleration performance is ensured.




Dual Variable Valve Timing-intelligent (VVT-i) System


a.

General

i.

The Dual VVT-i system is designed to control the intake and exhaust camshafts within a range of 60° and 30° respectively (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine operating conditions. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W128443C02
3.833,0.448 4.229,0.667 0.396,0.219 10 false *1 3.833,0.708 4.292,0.938 0.458,0.229 10 false *2 3.844,0.99 4.104,1.208 0.26,0.219 10 false *3 3.844,1.25 4.104,1.469 0.26,0.219 10 false *4 3.844,1.5 4.104,1.719 0.26,0.219 10 false *5 3.844,1.75 4.104,1.969 0.26,0.219 10 false *6 3.844,2.188 4.104,2.406 0.26,0.219 10 false *7 3.844,3 4.104,3.219 0.26,0.219 10 false *9 3.844,3.302 4.344,3.521 0.5,0.219 10 false *10 3.833,3.615 4.375,3.823 0.542,0.208 10 false *11 3.844,3.979 4.188,4.198 0.344,0.219 10 false *12 5.792,2.979 6.052,3.198 0.26,0.219 10 false *13 5.802,3.229 6.063,3.448 0.26,0.219 10 false *14 5.802,3.49 6.063,3.708 0.26,0.219 10 false *15 4.865,2.281 5.125,2.5 0.26,0.219 10 false *8
*1 Exhaust Camshaft Timing Oil Control Valve (Bank 2) *2 Intake Camshaft Timing Oil Control Valve (Bank 2)
*3 Exhaust VVT Sensor RH *4 Intake VVT Sensor RH
*5 Camshaft Position Sensor *6 Intake VVT Sensor LH
*7 Exhaust VVT Sensor LH *8 ECM
*9 Crankshaft Position Sensor *10 Exhaust Camshaft Timing Oil Control Valve (Bank 1)
*11 Intake Camshaft Timing Oil Control Valve (Bank 1) *12 Engine Coolant Temperature Sensor
*13 Mass Air Flow Meter *14 Throttle Position Sensor
*15 Vehicle Speed Signal - -



ii.

By using the engine speed, intake air volume, throttle position and engine coolant temperature, the ECM calculates optimal valve timing for each driving condition and controls the camshaft timing oil control valves. In addition, the ECM uses signals from the intake and exhaust VVT sensors for each bank and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W128444E02
0.51,0.677 2.25,1 1.74,0.323 10 false Crankshaft Position Sensor 0.49,1.198 2.208,1.542 1.719,0.344 10 false Camshaft Position Sensor 0.677,1.729 2.125,2.052 1.448,0.323 10 false Mass Air Flow Meter 0.573,2.24 2.188,2.563 1.615,0.323 10 false Throttle Position Sensor 0.458,2.771 2.281,3.104 1.823,0.333 10 false Engine Coolant Temp. Sensor 0.49,3.302 2.281,3.625 1.792,0.323 8 false Intake and Exhaust VVT Sensors 0.688,3.823 2.01,4.146 1.323,0.323 10 false Vehicle Speed Signal 3.604,3.333 4.948,3.667 1.344,0.333 10 false Actual Valve Timing 3.896,2.781 4.656,3.104 0.76,0.323 10 false Correction 3.583,1.26 4.906,1.583 1.323,0.323 10 false Target Valve Timing 4.104,0.583 4.5,0.844 0.396,0.26 10 false ECM 4.75,2.354 5.406,2.719 0.656,0.365 10 false Feedback 5.24,1.688 5.958,2.281 0.719,0.594 10 true Duty Cycle Control 6.031,1.344 7.125,2.052 1.094,0.708 10 false Camshaft Timing Oil Control Valve



b.

Effectiveness of Dual VVT-i System

Condition Operation Timing/Position Objective Effect
During Idling
W128445E01
1.594,0.135 1.927,0.448 0.333,0.313 10 false TDC 1.646,1.813 1.979,2.125 0.333,0.313 10 false BDC 0.74,1 1.01,1.323 0.271,0.323 10 false EX 2.5,0.99 2.771,1.313 0.271,0.323 10 false IN

IN Latest Position Eliminating overlap to reduce blow back to the intake side.
·

Stabilized idle speed

·

Better fuel economy


EX Most Advanced Position
In Low Speed Range with Light to Medium Load
W128446E01
0.802,0.969 1.052,1.313 0.25,0.344 10 false EX 2.51,1.104 2.76,1.448 0.25,0.344 10 false IN

IN Retarded Retarding the intake valve close timing and reducing pumping loss. Increasing overlap and internal EGR.
·

Better fuel economy

·

Improved emission control


EX Retarded
In Low to Medium Speed Range with Heavy Load
W128447E01
0.781,1.104 1.021,1.49 0.24,0.385 10 false EX 2.458,0.979 2.698,1.365 0.24,0.385 10 false IN

IN Advanced Advancing the intake valve close timing reduces intake air blow back to the intake side and improves volumetric efficiency. Improved torque in low to medium speed range
EX Advanced
In High Speed Range with Heavy Load
W128448E01
0.823,1.146 1.083,1.438 0.26,0.292 10 false EX 2.5,1.135 2.76,1.427 0.26,0.292 10 false IN

IN Retarded Retarding the intake valve close timing improves volumetric efficiency using the inertia of the intake air. Improved output
EX Advanced
At Low Temperatures
W128445E02
0.823,1.031 1.083,1.292 0.26,0.26 10 false EX 2.448,1.021 2.708,1.281 0.26,0.26 10 false IN

IN Latest Position Eliminating overlap to reduce blow back to the intake side. Valve timing is fixed at extremely low temperatures and the control range is increased as the temperature rises.
·

Stabilized fast idle speed

·

Better fuel economy


EX Most Advanced Position
·

Upon Starting

·

Stopping Engine


W128445E02
0.823,1.031 1.083,1.292 0.26,0.26 10 false EX 2.448,1.021 2.708,1.281 0.26,0.26 10 false IN

IN Latest Position Valve timing is controlled and fixed to the optimal timing for engine starting. Improved startability
EX Most Advanced Position


c.

Construction

i.

VVT-i Controller

·

This controller consists of an outer housing that is driven by the timing chain sprocket, and a vane sub-assembly that is coupled to each camshaft.

·

The intake side uses a VVT-i controller with 3 vanes, and the exhaust side uses one with 4 vanes.

·

When the engine stops, the intake side VVT-i controller is locked at the most retarded angle by its lock pin, and the exhaust side controller is locked at the most advanced angle. This ensures excellent engine startability.

·

The oil pressure sent from the advance or retard side passages of the intake and exhaust camshafts causes rotation of the VVT-i controller vane sub-assembly relative to the timing chain sprocket, to vary the valve timing continuously.

·

An advance assist spring is provided on the exhaust side VVT-i controller. This helps to apply torque in the advanced angle direction so that the vane lock pin securely engages with the housing when the engine stops.

Intake Side VVT-i Controller
W128449C02
2.74,2.708 5.479,3.427 2.74,0.719 1.365,1.667 1.115,1.313 true 2.49,1.417 2.281,1.031 true 3.635,1.229 3.458,0.823 true 4.552,0.823 4.375,0.417 true 5.802,1.708 5.573,1.25 true 0.969,1.177 1.25,1.417 0.281,0.24 10 false *1 2.135,0.875 2.417,1.115 0.281,0.24 10 false *2 3.344,0.656 3.625,0.896 0.281,0.24 10 false *3 4.26,0.25 4.542,0.49 0.281,0.24 10 false *4 5.771,1.729 6.052,1.969 0.281,0.24 10 false *5 2.76,2.729 3.042,2.969 0.281,0.24 10 false *6 3.063,2.906 3.344,3.146 0.281,0.24 10 false *a 3.906,3.188 4.188,3.427 0.281,0.24 10 false *b 4.802,3.198 5.083,3.438 0.281,0.24 10 false *c
*1 Timing Rotor *2 Outer Housing
*3 Vane Sub-assembly (Coupled to Intake Camshaft) *4 Timing Chain Sprocket
*5 Intake Camshaft *6 Lock Pin
*a Oil Pressure *b Engine Operating
*c Engine Stopped - -


Exhaust Side VVT-i Controller
W128450C01
2.01,1.625 1.792,1.135 true 3.583,1.74 3.219,0.823 true 4.427,0.854 4.24,0.427 true 2.229,3.021 1.99,2.271 true 3.823,2.75 3.635,2.208 true 5.948,1.865 5.719,1.24 true 1.698,0.969 1.958,1.229 0.26,0.26 10 false *1 3.094,0.646 3.354,0.906 0.26,0.26 10 false *2 4.135,0.25 4.396,0.51 0.26,0.26 10 false *3 2.188,3.042 2.448,3.302 0.26,0.26 10 false *4 3.802,2.76 4.063,3.021 0.26,0.26 10 false *5 5.917,1.865 6.177,2.125 0.26,0.26 10 false *6
*1 Outer Housing *2 Lock Pin
*3 Timing Chain Sprocket *4 Advanced Assist Spring
*5 Vane Sub-assembly (Fixed on Exhaust Camshaft) *6 Exhaust Camshaft




ii.

Camshaft Timing Oil Control Valve

This camshaft timing oil control valve controls the spool valve using duty-cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advance or retard side. When the engine is stopped, the intake camshaft timing oil control valve will move to the retard position, and the exhaust side oil control valve will move to the advance position.

Intake Camshaft Timing Oil Control Valve
W131828C01
1.948,1.177 1.823,0.813 true 1.604,1.76 1.969,1.385 true 3.406,1.896 3.146,1.438 true 4.104,2.073 3.844,1.615 true 4.615,1.896 4.083,1.375 true 1.667,0.615 1.979,0.771 0.313,0.156 10 false *1 1.448,1.792 1.76,1.948 0.313,0.156 10 false *2 3.396,1.948 3.708,2.104 0.313,0.156 10 false *3 2.219,0.542 2.708,0.74 0.49,0.198 10 false *a (*e) 2.302,1.917 2.615,2.073 0.313,0.156 10 false *c 2.635,1.948 2.948,2.104 0.313,0.156 10 false *d 2.802,0.531 3.292,0.729 0.49,0.198 10 false *b (*e) 2.969,1.938 3.281,2.094 0.313,0.156 10 false *c 4.115,2.104 4.427,2.26 0.313,0.156 10 false *4 4.656,1.938 4.969,2.094 0.313,0.156 10 false *5
*1 Sleeve *2 Spring
*3 Spool Valve *4 Coil
*5 Plunger - -
*a To VVT-i Controller (Advance Side) *b To VVT-i Controller (Retard Side)
*c Drain *d Oil Pressure
*e On the exhaust side oil control valve, the advance and retard sides are reversed. - -





d.

Operation

i.

Advance

When the camshaft timing oil control valve is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

Intake Side
W128452C01
0.51,1.854 0.354,1.313 true 0.635,3.052 0.802,2.573 true 4.896,3.073 5.333,3.073 false 0.24,1.135 0.542,1.396 0.302,0.26 10 false *1 0.542,3.052 0.844,3.313 0.302,0.26 10 false *a 4.729,2.979 5.031,3.24 0.302,0.26 10 false *b 5.25,3.177 5.552,3.438 0.302,0.26 10 false *c 5.51,3.177 5.813,3.438 0.302,0.26 10 false *d 6.552,1.521 6.854,1.781 0.302,0.26 10 false *2
*1 Vane *2 ECM
*a Rotation Direction *b Oil Pressure
*c In *d Drain


Exhaust Side
W128453C01
1.208,1.021 1.208,1.521 true 1.229,2.583 1.115,3.021 true 6.365,3.229 5.958,3.229 false 1.135,0.865 1.438,1.115 0.302,0.25 10 false *1 1.021,3.021 1.323,3.271 0.302,0.25 10 false *a 4.125,2.198 4.427,2.448 0.302,0.25 10 false *2 6.302,3.365 6.604,3.615 0.302,0.25 10 false *c 6.583,3.375 6.885,3.625 0.302,0.25 10 false *d 5.792,3.156 6.094,3.406 0.302,0.25 10 false *b
*1 Vane *2 ECM
*a Rotation Direction *b Oil Pressure
*c In *d Drain




ii.

Retard

When the camshaft timing oil control valve is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

Intake Side
W128454C01
5.542,3.01 6.063,3.01 false 1.479,3.052 1.323,2.604 true 1.031,1.667 0.875,1.219 true 2.479,1.177 2.74,1.406 0.26,0.229 10 false *1 1.448,3.083 1.76,3.281 0.313,0.198 10 false *1 6.792,1.469 7.031,1.688 0.24,0.219 10 false *2 0.76,1.052 1,1.271 0.24,0.219 10 false *a 5.24,3.115 5.479,3.333 0.24,0.219 10 false *b 5.49,3.104 5.729,3.323 0.24,0.219 10 false *c 6.083,2.927 6.323,3.146 0.24,0.219 10 false *d
*1 Vane *2 ECM
*a Rotation Direction *b Drain
*c In *d Oil Pressure


Exhaust Side
W128455C01
6.385,3.219 6.781,3.219 false 1.146,1.031 1.229,1.573 true 1.031,2.375 0.792,2.969 true 0.677,2.979 0.938,3.229 0.26,0.25 10 false *1 4.146,2.188 4.406,2.438 0.26,0.25 10 false *2 1.052,0.854 1.313,1.104 0.26,0.25 10 false *a 6.042,3.365 6.302,3.615 0.26,0.25 10 false *b 6.333,3.365 6.594,3.615 0.26,0.25 10 false *c 6.781,3.125 7.042,3.375 0.26,0.25 10 false *d
*1 Vane *2 ECM
*a Rotation Direction *b Drain
*c In *d Oil Pressure




iii.

Hold

After reaching the target timing, the engine valve timing is maintained by keeping the camshaft timing oil control valve in the neutral position unless the engine operating conditions change.This maintains the engine valve timing at the desired target position by preventing the engine oil from running out of the oil control valve.





Acoustic Control Induction System (ACIS)


a.

General

i.

The ACIS is realized by using a bulkhead to divide the intake manifold into two stages, with an intake air control valve in the bulkhead being opened and closed to vary the effective length of the intake manifold in accordance with the engine speed and throttle valve opening angle. This increases the power output in all ranges from low to high speed.

System Diagram
W128456C01
2.313,0.74 2.917,1.333 true 2.99,0.344 3.375,0.771 true 3.052,1.979 3.188,2.208 true 3.156,3.24 2.906,3.573 true 3.802,0.552 4.146,0.333 true 2.833,0.229 3.104,0.458 0.271,0.229 10 false *1 2.146,0.594 2.417,0.823 0.271,0.229 10 false *2 3.177,2.208 3.448,2.438 0.271,0.229 10 false *3 2.781,3.573 3.052,3.802 0.271,0.229 10 false *4 5.177,1.875 5.448,2.104 0.271,0.229 10 false *5 4.146,0.229 4.417,0.458 0.271,0.229 10 false *6
*1 ACIS Actuator *2 Intake Air Control Valve
*3 Throttle Position Sensor *4 Crankshaft Position Sensor
*5 ECM *6 VSV (for ACIS)




b.

Intake Air Control Valve and ACIS Actuator

i.

The intake air control valve and actuator are integrated with the intake manifold. This valve opens and closes to change the effective length of the intake manifold in two stages.

W128457C01
3.667,1.333 3.542,0.354 true 2.042,1.417 1.625,1.229 true 3.448,0.156 3.76,0.354 0.313,0.198 10 false *1 1.458,1.115 1.771,1.313 0.313,0.198 10 false *2 5.229,0.406 5.542,0.604 0.313,0.198 10 false *a
*1 Intake Air Control Valve *2 ACIS Actuator
*a Front - -




c.

Operation

i.

When the Intake Control Valve Closes (VSV On)

The ECM activates the VSV so that the negative pressure acts on the diaphragm chamber of the actuator. This closes the control valve to match the longer pulsation cycle. As a result, the effective length of the intake manifold is lengthened and the intake efficiency in the low-to-medium speed range is improved when under heavy load, due to the dynamic effect of the intake air, thereby increasing the power output.

W128458E01
2.021,1.25 1.604,0.229 1.604,0.229 2,0.229 true 2.052,0.146 4.052,0.542 2,0.396 10 false Intake Air Control Valve (Closed) 5.083,1.167 5.604,1.49 0.521,0.323 10 true VSV On 4.167,1.104 4.531,1.438 0.365,0.333 10 false Wide 3.458,1.677 4.385,2.323 0.927,0.646 10 false Throttle Valve Opening Angle 4.073,2.385 4.542,2.74 0.469,0.354 10 false Narrow 4.604,2.771 4.917,3.135 0.313,0.365 10 false Low 5.302,2.948 6.219,3.344 0.917,0.396 10 false Engine Speed 6.552,2.781 6.885,3.135 0.333,0.354 10 false High 0.938,3.063 2.938,3.458 2,0.396 10 false : Effective intake manifold length



ii.

When the Intake Control Valve Opens (VSV Off)

The ECM deactivates the VSV so that atmospheric air is led into the diaphragm chamber of the actuator. This opens the control valve to match the shorter pulsation cycle. When the control valve is open, the effective length of the intake manifold is shortened and peak intake efficiency is shifted. This benefits the low, medium and high engine speed ranges at low loads and the high engine speed range under heavy load, thus providing greater output at high engine speeds.

W128459E01
2.031,1.156 1.583,0.292 1.583,0.292 1.854,0.292 true 1.906,0.219 3.844,0.563 1.938,0.344 10 false Intake Air Control Valve (Open) 5.448,1.948 6,2.313 0.552,0.365 10 true VSV Off 0.927,3.063 2.938,3.458 2.01,0.396 10 false : Effective intake manifold length 3.49,1.719 4.406,2.417 0.917,0.698 10 false Throttle Valve Opening Angle 4.177,1.125 4.531,1.438 0.354,0.313 10 false Wide 4.083,2.438 4.531,2.75 0.448,0.313 10 false Narrow 5.313,3 6.208,3.354 0.896,0.354 10 false Engine Speed 4.604,2.792 4.896,3.125 0.292,0.333 10 false Low 6.479,2.792 6.781,3.115 0.302,0.323 10 false High





Fuel Pump Control


a.

General

i.

In this vehicle, there are 2 types of fuel pump control. The fuel pump is controlled to an optimum speed to match the engine operating conditions, and the fuel pump operation is cut when the SRS airbags deploy.

·

The ECM transmits a fuel pump speed request signal to the fuel pump ECU that corresponds to the engine operating conditions. The fuel pump ECU receives this request signal and controls the speed of the fuel pump in 3 stages. As a result, under light engine loads, fuel pump speed is kept low to reduce electric power loss.

·

A fuel cut control is used to stop the fuel pump when any of the SRS airbags deploy. In this control, if an airbag deployment signal from the Airbag Sensor Assembly is detected by the ECM, the ECM will turn OFF the circuit opening relay. As a result, the power supply to Fuel Pump ECU is stopped, causing the fuel pump to stop operating. After the fuel cut control has been activated, turning the ignition switch from OFF to ON cancels the fuel cut control, and the engine can be restarted.

System Diagram
W131829E02
0.781,3.573 1.615,4.479 0.833,0.906 10 false Curtain Shield Airbag Sensor (RH or LH) 0.771,2.302 1.625,3.229 0.854,0.927 10 false Side and Curtain Shield Airbag Sensor (RH or LH) 0.771,1.052 1.625,1.979 0.854,0.927 10 false Front Airbag Sensors (RH and LH) 2.063,1.542 2.719,2.583 0.656,1.042 10 false Airbag Sensor Assembly 2.813,2.188 3.177,3.531 0.365,1.344 10 false CAN (V Bus) 3.51,1.906 3.865,2.229 0.354,0.323 10 false ECM 4.115,0.344 5.115,0.656 1,0.313 10 false Ignition Switch 5.802,0.333 6.802,0.646 1,0.313 10 false EFI Relay 5.667,0.896 7.073,1.427 1.406,0.531 10 false Circuit Opening Relay 4.198,1.406 4.938,2.396 0.74,0.99 10 false Fuel Pump Operation Request 4.219,2.865 4.958,3.854 0.74,0.99 10 false Diagnosis Signal 5.063,1.99 5.771,2.646 0.708,0.656 10 false Fuel Pump ECU 6.271,2.01 6.979,2.667 0.708,0.656 10 false Fuel Pump




b.

Function of Main Component

i.

Fuel Pump ECU

·

The Fuel Pump ECU controls fuel pump speed by receiving a duty cycle signal (FPC terminal input) from the ECM, control is performed to three stages.

·

The Fuel Pump ECU also detects failures in the input and output circuits at the Fuel Pump ECU and transmits the failure status to the ECM.

W131830E01
1.99,1.688 2.427,2.052 0.438,0.365 10 false ECM 2.76,0.438 4.219,1.052 1.458,0.615 10 false Fuel Pump Operation Request 3.094,1.438 3.885,1.823 0.792,0.385 10 false Duty Signal 2.698,1.115 3.156,1.313 0.458,0.198 10 false FPC 3.948,1.135 4.406,1.333 0.458,0.198 10 false FPC 3,2.708 4.083,3.021 1.083,0.313 10 false Diagnosis Signal 2.708,2.417 3.021,2.615 0.313,0.198 10 false DI 4.01,2.417 4.323,2.615 0.313,0.198 10 false DI 4.427,1.51 5.104,2.281 0.677,0.771 10 false Fuel Pump ECU 5.688,1.313 6.49,1.729 0.802,0.417 10 false Fuel Pump

FPC Terminal Input
FPC Input Signal (Duty Signal) Fuel Pump Speed
W128462E01
0.885,0.823 1.094,1.146 0.208,0.323 10 false +B 0.781,1.188 1.104,1.563 0.323,0.375 10 false GND

High
W128463E01
0.615,1.094 0.833,1.396 0.219,0.302 10 false +B 0.583,1.406 0.906,1.698 0.323,0.292 10 false GND 1.229,0.5 1.854,0.708 0.625,0.208 10 false 12.3 ms 1.188,0.771 1.625,0.99 0.438,0.219 10 false 8.2 ms

Middle
W128464E01
0.573,1.25 0.885,1.563 0.313,0.313 10 false GND 0.677,0.948 0.885,1.24 0.208,0.292 10 false +B 1.083,0.583 1.625,0.813 0.542,0.229 10 false 4.1 ms

Low
W128465E01
0.781,1.229 1.094,1.552 0.313,0.323 10 false GND

Stop





Air Injection System


a.

General

i.

To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.

·

For this system, the right bank (bank 2) and left bank (bank 1) each has an electric air pump, air injection control driver, air injection control valve, and air pressure sensor. Control of the right bank and left bank is performed independently. Two pumps are used to increase the amount of air supplied, shortening the catalyst warm-up time.

·

The ECM estimates the amount of air injected to the TWCs based on signals from the mass air flow meter in order to regulate the air injection time.

·

Air is injected under the following conditions.

Operation Conditions
Engine Coolant Temperature 5°C to 45°C (41°F to 113°F)
Intake Air Temperature 5°C (41°F) or more

System Diagram
W131849C01
1.188,2.281 1.417,2.125 true 1.156,3.969 1.396,4.146 true 1.688,2.333 1.875,2.469 true 1.688,3.969 1.927,3.854 true 2.469,0.781 2.781,0.938 0.313,0.156 10 false *1 1,2.292 1.313,2.448 0.313,0.156 10 false *2 1.948,2.417 2.26,2.573 0.313,0.156 10 false *3 2.031,3.271 2.344,3.427 0.313,0.156 10 false *4 2.74,1.406 3.052,1.563 0.313,0.156 10 false *5 2.75,2.333 3.063,2.49 0.313,0.156 10 false *6 5.125,3.271 5.438,3.427 0.313,0.156 10 false *7 5.99,1.635 6.302,1.792 0.313,0.156 10 false *8 2.51,5.802 2.823,5.958 0.313,0.156 10 false *1 1.01,3.844 1.323,4 0.313,0.156 10 false *2 1.948,3.76 2.26,3.917 0.313,0.156 10 false *3 2.75,3.573 3.063,3.729 0.313,0.156 10 false *5 2.74,4.521 3.052,4.677 0.313,0.156 10 false *6 5.969,3.302 6.281,3.458 0.313,0.156 10 false *9 5.979,5.365 6.292,5.521 0.313,0.156 10 false *10 0.688,1.833 1,1.99 0.313,0.156 10 false *a 0.75,4.302 1.063,4.458 0.313,0.156 10 false *a 3.979,0.427 4.292,0.583 0.313,0.156 10 false *b 3.927,5.406 4.24,5.563 0.313,0.156 10 false *b 3.938,5.656 4.25,5.813 0.313,0.156 10 false *c 4,0.698 4.313,0.854 0.313,0.156 10 false *c 4,0.969 4.313,1.125 0.313,0.156 10 false *d 3.917,5.927 4.229,6.083 0.313,0.156 10 false *d 3.281,1.979 3.594,2.135 0.313,0.156 10 false *e 3.24,4.167 3.552,4.323 0.313,0.156 10 false *e 4.135,2.135 4.448,2.292 0.313,0.156 10 false *f 4.135,4.26 4.458,4.458 0.323,0.198 10 false *g
*1 Air Injection Control Driver *2 Electric Air Pump
*3 Heater *4 AI HTR Relay
*5 Air Pressure Sensor *6 Air Injection Control Valve
*7 ECM *8 Engine Coolant Temp. Sensor
*9 Mass Air Flow Meter *10 Intake Air Temp. Sensor
*a Air *b Pump Actuation Request
*c Valve Actuation Request *d Diagnosis Signal
*e To Exhaust Manifold *f Right Bank (Bank 2)
*g Left Bank (Bank 1) - -





b.

Function of Main Component

i.

Electric Air Pump

·

Each electric air pump consists of a DC motor, an impeller and an air filter.

·

Each pump supplies air into an air injection control valve using its impeller.

·

The air filter is maintenance-free.

·

The structure and function of the electric air pump for the right bank and left bank are basically the same.

·

A heater is provided to prevent operation faults in cold condition.

W131831C01
3.958,3.74 6.865,6.625 2.906,2.885 1.917,2.917 2.438,2.417 true 2.896,5.479 2.646,4.885 true 5.021,4.844 4.49,4.344 true 5.208,5.635 4.635,6.042 true 6.26,4.146 5.885,4.354 true 3.469,3.25 3.74,2.583 true 1.698,2.927 2.01,3.083 0.313,0.156 10 false *1 3.344,3.333 3.656,3.49 0.313,0.156 10 false *2 2.927,5.583 3.24,5.74 0.313,0.156 10 false *3 4.281,4.198 4.594,4.354 0.313,0.156 10 false *4 4.406,5.99 4.719,6.146 0.313,0.156 10 false *5 2.292,0.115 2.604,0.271 0.313,0.156 10 false *a 3.104,0.406 3.417,0.563 0.313,0.156 10 false *b 4.021,3.781 4.333,3.938 0.313,0.156 10 false *c 6.313,4.042 6.625,4.198 0.313,0.156 10 false *6 4.625,0.438 4.938,0.594 0.313,0.156 10 false *a 5.292,1.094 5.604,1.25 0.313,0.156 10 false *b
*1 Electric Air Pump (For Right Bank) *2 Electric Air Pump (For Left Bank)
*3 Heater *4 Impeller
*5 DC Motor *6 Air Filter
*a Air In *b Air Out
*c Cross Section - -




ii.

Air Injection Control Valve

·

The air injection control valve is operated by a solenoid coil to control air injection and prevent back-flow of exhaust gas. Opening timing of the valve is synchronized with the operation timing of the electric air pump.

·

Each air pressure sensor is built into the corresponding air injection control valve.

·

The structure and function of the air injection control valve for the right bank and left bank are basically the same.

W128468C02
3.979,0.635 6.688,3.333 2.708,2.698 1.552,1.104 1.479,0.646 true 2.906,1.115 2.969,0.646 true 1.573,3.073 1.781,2 true 2.771,3.104 2.677,2.021 true 5.042,1.99 4.302,1.51 true 5.406,1.51 5.76,1.51 true 1.396,0.469 1.615,0.719 0.219,0.25 10 false *1 2.896,0.49 3.115,0.74 0.219,0.25 10 false *2 4.156,1.406 4.375,1.656 0.219,0.25 10 false *3 5.813,1.427 6.031,1.677 0.219,0.25 10 false *4 4.021,0.677 4.24,0.927 0.219,0.25 10 false *c 1.479,3.094 1.698,3.344 0.219,0.25 10 false *b 0.615,1.677 0.833,1.927 0.219,0.25 10 false *a 3.615,1.708 3.833,1.958 0.219,0.25 10 false *a 2.719,3.146 2.938,3.396 0.219,0.25 10 false *b 6.323,1.865 6.542,2.115 0.219,0.25 10 false *b 6.01,2.51 6.229,2.76 0.219,0.25 10 false *a
*1 Air Injection Control Valve (For Right Bank) *2 Air Injection Control Valve (For Left Bank)
*3 Valve *4 Solenoid Coil
*a Air Out *b Air In
*c Cross Section (For Right Bank) - -




iii.

Air Pressure Sensor

·

The air pressure sensor consists of a semiconductor, which has a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.

·

The structure and function of the air pressure sensor for the right bank and left bank are basically the same.

W128469E02
1.708,2.063 1.51,2.052 1.51,2.052 1.51,1 true 0.948,0.958 0.625,0.281 0.625,0.281 1.021,0.281 true 1.052,0.219 1.813,0.531 0.76,0.313 10 false Sensor Unit 1.75,2.01 2.865,2.667 1.115,0.656 10 false Air Pressure of Electric Air Pump 3.25,1.063 3.74,1.833 0.49,0.771 10 false Output Voltage 3.792,0.49 4.031,0.688 0.24,0.198 10 false (V) 3.698,0.76 3.969,0.938 0.271,0.177 10 false 4.5 5.865,2.052 6.281,2.25 0.417,0.198 10 false (kPa) 4.573,2.156 5.406,2.552 0.833,0.396 10 false Air Pressure 3.698,1.51 3.969,1.698 0.271,0.188 10 false 0.5 4.25,2.042 4.458,2.24 0.208,0.198 10 false 45 5.563,2.042 5.802,2.26 0.24,0.219 10 false 150

·

The ECM detects operation of the air injection system based on signals from the air pressure sensor as follows:

1.

When the electric air pump is ON and the air injection control valve is closed, the pressure is stable.

2.

When the electric air pump is ON and the air injection control valve is open, the pressure drops slightly and becomes unstable because of exhaust pulses.

3.

When the electric air pump is OFF and the air injection control valve is closed, the pressure remains at zero.

4.

When the electric air pump is OFF and air injection control valve is open, the pressure drops below zero and becomes unstable because of exhaust pulses.

W128470E02
0.042,0.563 0.792,0.917 0.75,0.354 10 false Example: 1 3.625,0.531 4.375,0.885 0.75,0.354 10 false Example: 2 0.052,3.063 0.802,3.417 0.75,0.354 10 false Example: 3 3.635,3.104 4.385,3.458 0.75,0.354 10 false Example: 4 0.26,0.948 0.844,1.323 0.583,0.375 10 false Pressure 3.792,0.927 4.375,1.302 0.583,0.375 10 false Pressure 0.302,3.479 0.885,3.854 0.583,0.375 10 false Pressure 3.833,3.49 4.417,3.865 0.583,0.375 10 false Pressure 0.823,2.042 0.938,2.281 0.115,0.24 10 false 0 4.365,2.042 4.479,2.281 0.115,0.24 10 false 0 0.823,4.583 0.938,4.823 0.115,0.24 10 false 0 4.365,4.615 4.479,4.854 0.115,0.24 10 false 0 2.74,2.052 3.052,2.385 0.313,0.333 10 false Time 6.271,2.042 6.583,2.375 0.313,0.333 10 false Time 6.271,4.604 6.583,4.938 0.313,0.333 10 false Time 2.75,4.604 3.063,4.938 0.313,0.333 10 false Time 0.938,2.667 3.531,2.969 2.594,0.302 10 false Air Injection Control Valve: Closed 0.938,2.365 3.542,2.667 2.604,0.302 10 false Electric Air Pump: On 4.458,2.365 7.063,2.667 2.604,0.302 10 false Electric Air Pump: On 4.458,2.667 7.052,2.969 2.594,0.302 10 false Air Injection Control Valve: Open 0.927,4.906 3.531,5.208 2.604,0.302 10 false Electric Air Pump: Off 0.938,5.25 3.531,5.552 2.594,0.302 10 false Air Injection Control Valve: Closed 4.469,4.917 7.073,5.219 2.604,0.302 10 false Electric Air Pump: Off 4.479,5.25 7.073,5.552 2.594,0.302 10 false Air Injection Control Valve: Open




iv.

Air Injection Control Driver

·

A semiconductor type air injection control driver is used. Activated by the ECM, this driver actuates the electric air pump and the air injection control valve.

·

The air injection driver also detects failures in the input and output circuits of the air injection driver and transmits the failure status to the ECM via duty cycle signals.

·

The basic functions of the air injection control driver for the right bank and left bank are the same. The following system chart shows the left bank (bank 1).

W128471E02
1.813,1.927 1.813,1.313 1.813,1.313 1.885,1.313 false 1.865,0.917 1.865,0.25 1.865,0.25 2.021,0.25 false 2.188,2.656 2.188,3.49 2.188,3.49 2.385,3.49 true 1.135,1.823 1.479,2.167 0.344,0.344 10 false ECM 2.073,0.167 3.271,0.896 1.198,0.729 10 false Electric Air Pump Actuation Request 1.792,0.958 2.135,1.177 0.344,0.219 10 false AIRP 3.135,0.969 3.375,1.177 0.24,0.208 10 false SIP 1.906,1.229 3.344,1.885 1.438,0.656 9 false Air Injection Control Valve Actuation Request 1.792,1.938 2.135,2.146 0.344,0.208 10 false AIRV 3.135,1.958 3.375,2.177 0.24,0.219 10 false SIV 2.427,3.406 3.552,3.771 1.125,0.365 10 false Duty Signal 1.813,2.99 2.115,3.198 0.302,0.208 10 false AIDI 3.24,2.958 3.406,3.177 0.167,0.219 10 false DI 3.5,1.688 4.292,2.344 0.792,0.656 10 false Air Injection Control Drive 4.417,1.198 4.656,1.385 0.24,0.188 10 false VP 4.427,2.323 4.688,2.5 0.26,0.177 10 false VV 5.073,1.521 5.677,1.865 0.604,0.344 10 false Electric Air Pump 4.573,3.021 6.281,3.635 1.708,0.615 10 false Air Injection Control Valve

DI Terminal Output
Condition AIRP AIRV Output (Duty Cycle Signal)
Open circuit in line between AIDI and DI terminals. - -
W128239E01
0.469,1.188 0.813,1.604 0.344,0.417 10 false GND

Failure in line between ECM terminals and air injection control driver. - -
W128244E02
0.458,1.208 0.823,1.583 0.365,0.375 10 false GND

Output failure at air injection control driver.(Failure in electric air pump actuation circuit) - -
W128240E03
0.458,1.26 0.802,1.688 0.344,0.427 10 false GND 1.427,0.625 2.031,0.917 0.604,0.292 10 false 20 ms

Output failure at air injection control driver.(Failure in air injection control valve actuation circuit) - -
W132031E01
0.458,1.229 0.927,1.583 0.469,0.354 10 false GND

Overheat failure of air injection control driver. - -
W132032E01
0.448,1.229 0.854,1.573 0.406,0.344 10 false GND

Normal On On
W132033E01
0.458,1.229 0.875,1.635 0.417,0.406 10 false GND

Off Off
W128244E02
0.458,1.208 0.823,1.583 0.365,0.375 10 false GND

On Off
Off On





Cranking Hold Function (Starter Control)


a.

General

i.

Once the ignition switch is turned to the START position, this function operates the starter until the engine starts, without having to hold the ignition switch in the START position. This prevents application of the starter for an inadequate length of time.


ii.

When the ECM detects a start signal from the ignition switch, it monitors engine speed (NE) and operates the starter until it determines that the engine has started.


iii.

A bypass wire with a diode is provided between the ignition switch and park/neutral position switch to enable engine cranking when the battery voltage is lower than usual.

System Diagram
W131832E01
3.229,4.438 5.354,5.406 2.125,0.969 0.677,4.917 1.333,5.229 0.656,0.313 10 false Battery 1.938,4.094 2.594,4.406 0.656,0.313 10 false Starter 0.667,2.698 1.177,3.313 0.51,0.615 10 false Starter Relay 1.781,1.927 3.635,2.229 1.854,0.302 10 false Park/Neutral Position Switch 4.74,0.656 6.375,1.427 1.635,0.771 10 false To ACC Relay (Built-in to Main Body ECU) 3.063,1.281 4.042,1.635 0.979,0.354 10 false ACC Cut Relay 5.458,2.729 6.438,3.083 0.979,0.354 10 false Ignition Switch 4.083,3.302 4.531,3.646 0.448,0.344 10 false ECM 3.417,4.5 5.719,4.875 2.302,0.375 10 false - Engine Speed Signal 3.417,4.906 5.333,5.24 1.917,0.333 10 false - Engine Coolant Temp. Signal 3.5,3.573 3.958,3.771 0.458,0.198 10 false STA 3.469,2.813 3.979,3.01 0.51,0.198 10 false STAR 4.292,2.604 4.802,2.802 0.51,0.198 10 false ACCR 4.708,3.49 5.219,3.688 0.51,0.198 10 false STSW 5.229,2.448 5.74,2.646 0.51,0.198 10 false ST2 5.188,1.656 5.698,1.854 0.51,0.198 10 false ACC



b.

Operation

i.

As indicated in the timing chart shown below, when the ECM detects a start signal (STSW) from the ignition switch, the ECM outputs a starter relay drive signal (STAR) that flows through the park/neutral position switch to turn on the starter relay. As a result, the starter operates. (If the engine is already running, the ECM will not turn on the starter relay.)


ii.

After the engine speed rises above approximately 500 rpm, the ECM determines that the engine has started and stops the output of the starter relay drive signal (STAR) to stop the operation of the starter.


iii.

The ECM outputs an ACC cut relay drive signal (ACCR) to turn on the ACC cut relay, in order to prevent accessory light flickering from occurring while cranking.


iv.

If the engine fails to start, the starter operates as long as its maximum continuous operation time and stops automatically. The maximum continuous operation time is approximately 2 seconds through 25 seconds depending on the engine coolant temperature. When the engine coolant temperature is extremely low, maximum cranking time is approximately 25 seconds. When the engine is warmed up sufficiently, maximum cranking time is approximately 2 seconds.


v.

The cranking hold function of this system has following safety features:

·

Starter operation is limited to a maximum of 30 seconds to protect the starter motor.

·

The starter will stop if the ECM cannot detect an engine speed signal (NE) while the starter is operating.

Timing Chart
W131833E01
1.833,3.979 5.542,4.771 3.708,0.792 3.719,1.469 3.948,1.26 3.948,1.26 4.677,1.26 true 3.792,3.969 4.198,3.042 true 0.292,0.74 1.229,1.177 0.938,0.438 9 false Ignition Switch (Start Signal) 1.573,0.49 2.052,0.771 0.479,0.281 9 false START 1.688,1.031 2.042,1.344 0.354,0.313 9 false OFF 1.688,0.635 2.031,0.906 0.344,0.271 9 false (On) 0.208,1.542 1.646,2.083 1.438,0.542 9 false Starter Relay (Starter Relay Drive Signal) 1.677,1.521 2.031,1.833 0.354,0.313 9 false On 1.677,1.906 2.031,2.219 0.354,0.313 9 false Off 1.688,2.104 2.042,2.417 0.354,0.313 9 false On 1.688,2.563 2.042,2.875 0.354,0.313 9 false Off 0.125,2.25 1.479,3.198 1.354,0.948 9 false Accessory Power (ACC Cut Relay Drive Signal) 1.677,2.25 2.031,2.563 0.354,0.313 9 false (Off) 1.677,2.688 2.031,3 0.354,0.313 9 false (On) 4.719,1.177 7.01,1.646 2.292,0.469 10 false Cranking Limit Approx. 2 to 25 sec. 0.104,3.469 1.813,3.865 1.708,0.396 10 false Engine Speed Signal (NE) 5.531,2.698 6.958,3.344 1.427,0.646 10 false Successful Starting of Engine 5.552,3.438 6.979,4.083 1.427,0.646 10 false Failed Starting of Engine 1.938,4.021 5.458,4.708 3.521,0.688 10 false ECM determines that the engine has started successfully when the engine speed is approximately 500 rpm.





Evaporative Emission Control System


a.

General

i.

The evaporative emission control system prevents the fuel vapors created in the fuel tank from being released directly into the atmosphere.


ii.

The charcoal canister assembly stores the fuel vapors that have been created in the fuel tank.

·

The ECM controls the purge VSV in accordance with the driving conditions in order to direct the fuel vapors into the engine, where they are burned.

·

In this system, the ECM checks for evaporative emission leaks and outputs a Diagnostic Trouble Code (DTC) in the event of a malfunction. An evaporative emission leak check consists of an application of vacuum to the evaporative emission system and monitoring the system for changes in pressure in order to detect a leak.

·

This system consists of the purge VSV, charcoal canister assembly, canister pump module and ECM.

·

A refueling vapor recovery function is provided.

·

A canister pressure sensor has been included with the canister pump module.

·

A canister filter has been provided on the fresh air line. This canister filter is maintenance-free.

·

The following are the typical conditions necessary to enable an evaporative emission (EVAP) leak check:

*: If engine coolant temperature does not drop below 35°C (95°F), this time is extended to 7 hours. After that, if the temperature is still not less than 35°C (95°F), the time is extended to 9.5 hours.

Typical Enabling Conditions
·

5 hours have elapsed after the engine has been turned off*.

·

Altitude: Below 2400 m (8000 feet)

·

Battery Voltage: 10.5 V or more

·

Ignition Switch: Off

·

Engine Coolant Temperature: 4.4°C to 35°C (40°F to 95°F)

·

Intake Air Temperature: 4.4°C to 35°C (40°F to 95°F)




HINT:

The canister pump module performs a fuel evaporative emission leak check. This check is conducted approximately 5 hours after the engine is turned off. Sound may be heard coming from underneath the luggage compartment for several minutes. This does not indicate a malfunction.

·

A pinpoint pressure test procedure is used by pressurizing the fresh air line that runs from the canister pump module to the air filler neck. For details, refer to the Repair Manual.





b.

System Diagram

W131838C01
1.781,1.552 1.552,1.427 true 3.49,1.646 3.354,1.813 true 4.448,3.51 4.271,3.396 true 4.896,3.875 4.75,3.979 true 5.646,3.125 5.5,3.229 true 0.542,1.208 0.854,1.365 0.313,0.156 10 false *1 0.719,3.594 1.031,3.75 0.313,0.156 10 false *2 1.385,1.313 1.698,1.469 0.313,0.156 10 false *3 3.49,1.469 3.802,1.625 0.313,0.156 10 false *4 3.896,2.271 4.208,2.427 0.313,0.156 10 false *5 4.115,3.271 4.427,3.427 0.313,0.156 10 false *6 4.552,3.99 4.865,4.146 0.313,0.156 10 false *7 5.688,3.052 6,3.208 0.313,0.156 10 false *8 1.125,0.365 1.438,0.521 0.313,0.156 10 false *a 1.26,2.74 1.573,2.896 0.313,0.156 10 false *b 2.167,2.99 2.479,3.146 0.313,0.156 10 false *c 6.323,3.781 6.635,3.938 0.313,0.156 10 false *9
*1 Purge VSV *2 ECM
*3 Canister Filter *4 Fuel Tank Assembly
*5 Canister Pump Module *6 Leak Detection Pump
*7 Canister Pressure Sensor *8 Vent Valve
*9 Charcoal Canister Assembly - -
*a To Intake Manifold *b Purge Air Line
*c Fresh Air Line - -



c.

Function of Main Components

Component Function
ECM Controls the canister pump module and the purge VSV in accordance with the signals from various sensors, in order to achieve a purge volume that suits the driving conditions. In addition, the ECM monitors the system for any leak and stores a DTC if a malfunction is found.
Charcoal Canister Assembly Contains activated charcoal to absorb the fuel vapor that is created in the fuel tank assembly.
Fresh Air Line Fresh air goes into the charcoal canister assembly and the cleaned drain air goes out into the atmosphere.
Canister Pump Module Vent Valve Opens and closes the fresh air line in accordance with signals from the ECM.
Leak Detection Pump Applies vacuum to the evaporative emission system in accordance with signals from the ECM.
Canister Pressure Sensor Detects the pressure in the evaporative emission system and sends the signals to the ECM.
Purge VSV Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister assembly into the intake manifold. In system monitoring mode, this valve controls the introduction of vacuum into the fuel tank assembly.
Canister Filter Prevents dust and debris in the fresh air from entering the system.


d.

Construction and Operation

i.

Canister Pump Module

·

The canister pump module consists of a vent valve, reference orifice, canister pressure sensor, leak detection pump, and pump motor.

·

The vent valve switches the passages in accordance with the signals received from the ECM.

·

A DC type brushless motor is used for the pump motor.

W131839C01
3.781,1.823 4.833,2.396 true 5.719,1.708 6.448,1.208 true 5.5,1.906 6.302,2.094 true 5.156,2.333 5.979,2.938 true 5.25,2.698 5.708,3.177 true 3.49,1.698 3.802,1.854 0.313,0.156 10 false *1 5.719,3.24 6.031,3.396 0.313,0.156 10 false *2 6.063,2.979 6.375,3.135 0.313,0.156 10 false *3 6.365,2.063 6.677,2.219 0.313,0.156 10 false *4 6.469,1.115 6.781,1.271 0.313,0.156 10 false *5 1.188,0.25 1.5,0.406 0.313,0.156 10 false *a 5.042,3.375 5.354,3.531 0.313,0.156 10 false *b 4.583,0.25 4.896,0.406 0.313,0.156 10 false *a
*1 Vent Valve *2 Reference Orifice
*3 Canister Pressure Sensor *4 Pump Motor
*5 Leak Detection Pump - -
*a Fresh Air *b To Charcoal Canister Assembly


Simple Diagram
W131840C01
3.104,1.875 3.219,1.719 true 4.604,2.865 4.542,2.688 true 4.333,3.188 4.25,2.979 true 4.417,1.51 4.729,1.302 true 2.083,0.385 2.396,0.542 0.313,0.156 10 false *1 2.49,2.052 2.802,2.208 0.313,0.156 10 false *2 3.271,1.583 3.583,1.74 0.313,0.156 10 false *3 3.24,2.615 3.552,2.771 0.313,0.156 10 false *4 4.365,3.188 4.677,3.344 0.313,0.156 10 false *5 1.677,1.417 1.99,1.573 0.313,0.156 10 false *a 5.625,1.823 5.938,1.979 0.313,0.156 10 false *b 4.396,2.521 4.708,2.677 0.313,0.156 10 false *3 4.74,1.167 5.052,1.323 0.313,0.156 10 false *6
*1 Canister Pump Module *2 Leak Detection Pump
*3 Filter *4 Canister Pressure Sensor
*5 Reference Orifice [0.5 mm (0.020 in.) Diameter] *6 Vent Valve (Off)
*a Fresh Air *b To Charcoal Canister Assembly




ii.

Fuel Inlet (Fresh Air Inlet)

This evaporative emission control system has its fresh air line inlet located near the fuel inlet. The fresh air from the atmosphere and drain air cleaned by the charcoal canister will go in and out of the system through the passage shown below.

W131834C01
1.677,0.302 2.323,0.427 true 2.688,2.208 3.24,1.906 true 3.229,0.281 3.75,0.313 true 5.167,1.75 5.688,1.781 true 5.167,2.25 5.083,1.792 true 1.417,0.219 1.729,0.375 0.313,0.156 10 false *1 2.448,2.198 2.76,2.354 0.313,0.156 10 false *2 5.125,2.281 5.438,2.438 0.313,0.156 10 false *c 3.802,0.198 4.115,0.354 0.313,0.156 10 false *a 5.729,1.74 6.042,1.896 0.313,0.156 10 false *b
*1 Fuel Tank Cap *2 Fuel Inlet Pipe
*a Fresh Air *b To Charcoal Canister
*c Cleaned Drain Air - -





e.

System Operation

i.

Purge Flow Control

·

When the engine has reached a predetermined state (closed loop, engine coolant temperature above 80°C (176°F), etc.), stored fuel vapor is purged from the charcoal canister assembly whenever the purge VSV is opened by the ECM.

·

The ECM will change the duty ratio cycle of the purge VSV, thus controlling purge flow volume. Purge flow volume is determined by intake manifold pressure and the duty ratio cycle of the purge VSV. Atmospheric pressure is allowed into the charcoal canister assembly to ensure that purge flow is constantly maintained whenever purge vacuum is applied to the charcoal canister assembly.

W131841C01
1.156,0.906 1.469,1.063 0.313,0.156 10 false *1 1.24,2.729 1.552,2.885 0.313,0.156 10 false *2 5.75,3.063 6.063,3.219 0.313,0.156 10 false *3 1.521,0.313 1.833,0.469 0.313,0.156 10 false *a 1.75,0.802 2.063,0.958 0.313,0.156 10 false *b
*1 Purge VSV (Open) *2 ECM
*3 Charcoal Canister Assembly - -
*a To Intake Manifold *b Atmosphere




ii.

Refueling Vapor Recovery

When the internal pressure of the fuel tank increases during refueling, the fuel vapors enter the charcoal canister assembly. The air that has had the fuel vapors removed from it will be discharged through the fresh air line. The vent valve is used to open and close the fresh air line, and it is always open (even when the engine is stopped) except when the vehicle is in monitoring mode (the valve will be open as long as the vehicle is not in monitoring mode). If the vehicle is refueled in system monitoring mode, the ECM will recognize the refueling by way of the canister pressure sensor, which detects the sudden pressure increase in the fuel tank, and the ECM will open the vent valve.

W131842C01
5.167,2.5 5.344,2.323 true 0.906,0.792 1.219,0.948 0.313,0.156 10 false *1 5.896,3.115 6.208,3.271 0.313,0.156 10 false *3 5.323,2.167 5.635,2.323 0.313,0.156 10 false *2
*1 Purge VSV (Closed) *2 Vent Valve
*3 Charcoal Canister Assembly - -




iii.

EVAP Leak Check

1.

General

The EVAP leak check operates in accordance with the following timing chart:

Timing Chart
W131843E01
0.344,0.583 1.156,0.906 0.813,0.323 10 false Purge VSV 1.969,0.5 2.667,0.781 0.698,0.281 10 false On (Open) 1.917,0.813 2.698,1.146 0.781,0.333 10 false Off (Closed) 2.375,1.167 2.677,1.49 0.302,0.323 10 false On 1.99,1.469 2.688,1.771 0.698,0.302 10 false Off (Vent) 0.365,1.25 1.229,1.625 0.865,0.375 10 false Vent Valve 2.385,1.802 2.698,2 0.313,0.198 10 false On 2.396,2.083 2.708,2.281 0.313,0.198 10 false Off 0.344,1.948 1.177,2.25 0.833,0.302 10 false Pump Motor 1.823,2.656 2.708,3.344 0.885,0.688 10 false Atmospheric Pressure 1.604,3.635 2.74,4.073 1.135,0.438 10 false 0.02 in. Pressure 0.396,3.167 1.552,3.521 1.156,0.354 10 false System Pressure 2.906,4.063 3.219,4.26 0.313,0.198 10 false 1) 3.49,4.052 3.802,4.25 0.313,0.198 10 false 2) 4.698,4.042 5.01,4.24 0.313,0.198 10 false 3) 5.583,4.052 5.896,4.25 0.313,0.198 10 false 4) 6.188,4.052 6.5,4.25 0.313,0.198 10 false 5) 6.75,4.042 7.063,4.24 0.313,0.198 10 false 6)

Order Operation Description Time
1) Atmospheric Pressure Measurement The ECM turns the vent valve off (vent) and measures EVAP system pressure to memorize the atmospheric pressure. 60 sec.
2) 0.02 in. Leak Pressure Measurement The leak detection pump creates negative pressure (vacuum) through a 0.02 in. orifice and the pressure is measured. The ECM determines this as the 0.02 in. leak pressure. 360 sec.
3) EVAP Leak Check The leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized pressure is larger than the 0.02 in. leak pressure, the ECM determines that the EVAP system has a leak.
If the EVAP pressure does not stabilize within 15 minutes, the ECM cancels EVAP monitor.
Within 15 min.
4) Purge VSV Monitor The ECM opens the purge VSV and measures the EVAP pressure increase. If the increase is large, the ECM interprets this as normal. 10 sec.
5) Repeat 0.02 in. Leak Pressure Measurement The leak detection pump creates negative pressure (vacuum) through the 0.02 in. orifice and the pressure is measured. The ECM determines this as the 0.02 in. leak pressure. 20 sec.
6) Final Check The ECM measures the atmospheric pressure and records the monitor result. -


2.

Atmospheric Pressure Measurement

1.

When the ignition switch is turned off, the purge VSV and the vent valve are turned off. As a result, atmospheric pressure is introduced into the charcoal canister assembly.

2.

The ECM measures the atmospheric pressure using the canister pressure sensor.

3.

If the measured atmospheric pressure is out of range, the ECM actuates the leak detection pump in order to monitor the changes in the pressure.

W131844E01
1.917,0.708 2,0.177 2,0.177 2.448,0.177 true 5.104,2.271 4.896,1.875 4.896,1.875 4.792,1.875 true 2.781,8.479 3.063,8.479 3.063,8.479 3.156,8.104 true 0.5,1.26 1.521,1.656 1.021,0.396 10 false Purge VSV (Off) 2.5,0.094 3.344,0.385 0.844,0.292 10 false Atmosphere 4.01,3.271 5.469,3.594 1.458,0.323 10 false Canister Pump Module 3.802,1.792 4.802,2.146 1,0.354 10 false Vent Valve (Off) 1.156,2.573 1.531,2.865 0.375,0.292 10 false ECM 0.531,4.365 1.323,4.667 0.792,0.302 10 false Purge VSV 2.115,4.229 2.844,4.531 0.729,0.302 10 false On (Open) 2.094,4.604 2.854,4.896 0.76,0.292 10 false Off (Closed) 0.51,5.156 1.302,5.458 0.792,0.302 10 false Vent Valve 2.552,4.99 2.844,5.323 0.292,0.333 10 false On 2.146,5.385 2.823,5.677 0.677,0.292 10 false Off (Vent) 0.573,5.969 1.365,6.271 0.792,0.302 10 false Pump Motor 2.531,5.75 2.823,6.083 0.292,0.333 10 false On 2.531,6.156 2.823,6.49 0.292,0.333 10 false Off 1.906,6.563 2.833,7.125 0.927,0.563 10 false Atmospheric Pressure 0.521,7.01 1.667,7.344 1.146,0.333 10 false System Pressure 1.771,7.438 2.917,7.771 1.146,0.333 10 false 0.02 in. Pressure 0.479,8.406 2.792,8.792 2.313,0.385 10 false Atmospheric Pressure Measurement


3.

0.02 in. Leak Pressure Measurement

1.

The purpose of this measurement is to confirm leak detection pump operation, and to provide a baseline measurement value that will be used for comparison in subsequent leak test steps.

2.

The vent valve remains off, atmospheric pressure is introduced into the charcoal canister assembly and the ECM actuates the leak detection pump, creating a vacuum in the piping close to the canister pressure sensor.

3.

At this time, the pressure will not decrease below what is referred to as the 0.02 in. pressure due to the atmospheric pressure that enters the piping close to the pump and sensor through the 0.02 in. diameter reference orifice.

4.

The ECM compares this pressure against the standard. If the pressure is within the acceptable range, the ECM stores this pressure as the 0.02 in. leak pressure.

5.

If the pressure is below the standard, the ECM will determine that the reference orifice is clogged and store DTC P043E in its memory.

6.

If the pressure is above the standard, the ECM will determine that a high flow rate pressure is passing through the reference orifice and store DTCs P043F, P2401 and P2402 in its memory.

W131845E01
1.885,0.729 1.979,0.188 1.979,0.188 2.417,0.188 true 5.094,2.99 5.521,3.375 5.521,3.375 5.708,3.375 true 5.042,2.26 4.927,1.844 4.927,1.844 4.771,1.844 true 3.479,8.031 3.188,8.417 3.188,8.417 2.99,8.417 true 2.521,0.104 3.333,0.438 0.813,0.333 10 false Atmosphere 0.458,1.25 1.5,1.552 1.042,0.302 10 false Purge VSV (Off) 1.125,2.573 1.49,2.865 0.365,0.292 10 false ECM 3.875,3.24 5.354,3.542 1.479,0.302 10 false Canister Pump Module 5.76,3.292 6.906,3.583 1.146,0.292 10 false Reference Orifice 3.771,1.76 4.823,2.135 1.052,0.375 10 false Vent Valve (Off) 0.094,4.375 0.979,4.667 0.885,0.292 10 false Purge VSV 0.083,5.135 0.969,5.427 0.885,0.292 10 false Vent Valve 0.042,5.948 0.927,6.24 0.885,0.292 10 false Pump Motor 0.052,7.063 1.25,7.354 1.198,0.292 10 false System Pressure 1.865,4.198 2.604,4.521 0.74,0.323 10 false On (Open) 1.823,4.615 2.635,4.927 0.813,0.313 10 false Off (Closed) 2.302,4.969 2.604,5.26 0.302,0.292 10 false On 1.948,5.354 2.604,5.677 0.656,0.323 10 false Off (Vent) 2.313,5.729 2.583,6.042 0.271,0.313 10 false On 2.323,6.115 2.583,6.448 0.26,0.333 10 false Off 1.688,6.563 2.573,7.146 0.885,0.583 10 false Atmospheric Pressure 1.469,7.427 2.635,7.74 1.167,0.313 10 false 0.02 in. Pressure 0.615,8.344 2.99,8.75 2.375,0.406 10 false 0.02 in. Leak Pressure Measurement


4.

EVAP Leak Check

1.

While actuating the leak detection pump, the ECM turns the vent valve on in order to introduce a vacuum into the charcoal canister assembly.

2.

When the pressure in the system stabilizes, the ECM compares this pressure and the 0.02 in. pressure in order to determine if a leak is present.

3.

If the detected pressure is below the 0.02 in. pressure, the ECM determines that there is no leak.

4.

If the detected pressure is above the 0.02 in. pressure and near atmospheric pressure, the ECM determines that there is a gross leak (large hole) and stores DTC P0455 in its memory.

5.

If the detected pressure is above the 0.02 in. pressure, the ECM determines that there is a small leak (minor leak) and stores DTC P0456 in its memory.

W131846E01
1.865,0.667 1.969,0.167 1.969,0.167 2.49,0.167 true 5.104,2.219 4.906,1.823 4.906,1.823 4.74,1.823 true 5.094,3.021 5.458,3.344 5.458,3.344 5.729,3.344 true 4.302,8.021 4.167,8.51 4.167,8.51 3.906,8.51 true 3.552,7.594 3.979,7.594 3.979,7.594 4.198,7.417 true 5.906,0.708 6.094,0.198 6.094,0.198 6.365,0.198 true 2.531,0.104 3.396,0.385 0.865,0.281 10 false Atmosphere 0.469,1.26 1.531,1.531 1.063,0.271 10 false Purge VSV (Off) 1.125,2.604 1.5,2.938 0.375,0.333 10 false ECM 3.792,3.26 5.271,3.604 1.479,0.344 10 false Canister Pump Module 3.76,1.75 4.781,2.052 1.021,0.302 10 false Vent Valve (On) 5.792,3.26 6.958,3.594 1.167,0.333 10 false Reference Orifice 0.156,4.323 0.979,4.604 0.823,0.281 10 false Purge VSV 0.125,5.115 0.948,5.396 0.823,0.281 10 false Vent Valve 0.135,5.875 0.958,6.156 0.823,0.281 10 false Pump Motor 0.083,6.948 1.25,7.354 1.167,0.406 10 false System Pressure 1.677,4.177 2.406,4.448 0.729,0.271 10 false On (Open) 1.604,4.552 2.448,4.875 0.844,0.323 10 false Off (Closed) 2.125,4.979 2.417,5.26 0.292,0.281 10 false On 1.74,5.344 2.417,5.615 0.677,0.271 10 false Off (Vent) 2.073,5.729 2.365,6.052 0.292,0.323 10 false On 2.083,6.135 2.406,6.417 0.323,0.281 10 false Off 1.438,6.583 2.365,7.219 0.927,0.635 10 false Atmospheric Pressure 1.25,7.417 2.375,7.771 1.125,0.354 10 false 0.02 in. Pressure 4.229,6.375 4.729,6.563 0.5,0.188 10 true P0455 4.323,7.021 4.781,7.208 0.458,0.188 10 true P0456 3.042,7.5 3.583,7.76 0.542,0.26 10 false Normal 2.583,8.448 3.875,8.771 1.292,0.323 10 false EVAP Leak Check 6.479,0.115 7.042,0.479 0.563,0.365 10 false Vacuum


5.

Purge VSV Monitor

1.

After completing an EVAP leak check, the ECM turns the purge VSV on (open) with the leak detection pump actuated, and introduces the atmospheric pressure from the intake manifold to the charcoal canister assembly.

2.

If the pressure change at this time is within the normal range (a pressure change occurs), the ECM determines the condition to be normal.

3.

If the pressure change is out of the normal range (insufficient pressure change occurs), the ECM will stop the purge VSV monitor (purge monitor) and store DTC P0441 in its memory.

W131847E01
1.875,0.656 1.938,0.156 1.938,0.156 2.271,0.156 true 1.156,0.292 1.365,0.281 1.365,0.281 1.563,0.188 true 5.073,2.167 4.885,1.844 4.885,1.844 4.75,1.844 true 4.802,7.094 4.615,6.771 4.615,6.771 4.479,6.771 true 4.948,7.552 5.188,7.042 5.188,7.042 5.354,7.042 true 4.875,8.01 4.771,8.417 4.771,8.417 4.583,8.417 true 0.323,0.229 1.146,0.5 0.823,0.271 10 false Atmosphere 2.365,0.073 3.188,0.344 0.823,0.271 10 false Atmosphere 0.229,0.917 1.01,1.594 0.781,0.677 10 false Purge VSV (On) 1.135,2.625 1.5,3 0.365,0.375 10 false ECM 3.75,1.76 4.781,2.052 1.031,0.292 10 false Vent Valve (On) 4,3.25 5.458,3.542 1.458,0.292 10 false Canister Pump Module 0.094,5.115 0.938,5.469 0.844,0.354 10 false Vent Valve 0.052,4.385 0.917,4.698 0.865,0.313 10 false Purge VSV 0.073,5.917 1.021,6.271 0.948,0.354 10 false Pump Motor 0.031,7.052 1.135,7.375 1.104,0.323 10 false System Pressure 1.333,4.198 2.063,4.51 0.729,0.313 10 false On (Open) 1.281,4.594 2.063,4.938 0.781,0.344 10 false Off (Closed) 1.75,4.969 2.063,5.292 0.313,0.323 10 false On 1.448,5.333 2.073,5.708 0.625,0.375 10 false Off (Vent) 1.781,5.729 2.052,6.01 0.271,0.281 10 false On 1.781,6.115 2.073,6.396 0.292,0.281 10 false Off 1.167,6.542 2.042,7.146 0.875,0.604 10 false Atmospheric Pressure 0.906,7.417 2.01,7.75 1.104,0.333 10 false 0.02 in. Pressure 3.958,6.708 4.542,7 0.583,0.292 10 false Normal 5.427,6.969 5.948,7.26 0.521,0.292 10 false P0441 3.313,8.354 4.688,8.552 1.375,0.198 10 false Purge VSV Monitor


6.

Repeat 0.02 in. Leak Pressure Measurement

1.

While the ECM operates the leak detection pump, the purge VSV and vent valve are turned off and a repeat 0.02 in. leak pressure measurement is performed.

2.

The ECM compares the measured pressure with the pressure during the EVAP leak check.

3.

If the pressure during the EVAP leak check is less than the repeat 0.02 in. leak pressure measurement, the ECM determines that there is no leak.

4.

If the pressure during the EVAP leak check is above the repeat 0.02 in. leak pressure measurement, the ECM determines that there is a small leak and stores DTC P0456 in its memory.

W131848E01
1.896,0.698 1.99,0.229 1.99,0.229 2.24,0.229 true 5.094,3.01 5.479,3.354 5.479,3.354 5.74,3.354 true 5.073,2.281 4.896,1.865 4.896,1.865 4.75,1.865 true 5.792,8.031 5.719,8.396 5.719,8.396 5.51,8.396 true 2.344,0.156 3.177,0.479 0.833,0.323 10 false Atmosphere 0.469,1.271 1.51,1.615 1.042,0.344 10 false Purge VSV (Off) 1.167,2.604 1.594,2.917 0.427,0.313 10 false ECM 3.802,3.24 5.281,3.635 1.479,0.396 10 false Canister Pump Module 5.781,3.292 7.042,3.625 1.26,0.333 10 false Reference Orifice 3.771,1.792 4.802,2.125 1.031,0.333 10 false Vent Valve (Off) 1.656,4.188 2.344,4.479 0.688,0.292 10 false On (Open) 0.083,5.115 0.958,5.438 0.875,0.323 10 false Vent Valve 0.094,5.906 1.417,6.229 1.323,0.323 10 false Pump Motor 0.063,7.01 1.198,7.365 1.135,0.354 10 false System Pressure 1.594,4.583 2.396,4.875 0.802,0.292 10 false Off (Closed) 2.125,4.979 2.396,5.271 0.271,0.292 10 false On 1.74,5.344 2.406,5.667 0.667,0.323 10 false Off (Vent) 2.115,5.729 2.417,6 0.302,0.271 10 false On 2.115,6.125 2.417,6.406 0.302,0.281 10 false Off 1.521,6.563 2.406,7.125 0.885,0.563 10 false Atmospheric Pressure 1.24,7.396 2.375,7.813 1.135,0.417 10 false 0.02 in. Pressure 4.208,7.104 4.76,7.302 0.552,0.198 10 false P0456 3.885,7.51 4.385,7.792 0.5,0.281 10 false Normal 2.698,8.333 5.49,8.677 2.792,0.344 10 false Repeat 0.02 in. Leak Pressure Measurement 0.052,4.344 0.927,4.667 0.875,0.323 10 false Purge VSV






Diagnosis


a.

When the ECM detects a malfunction, the ECM records the fault and memorizes the information that relates to the fault. Furthermore, it illuminates or blinks the Malfunction Indicator Lamp (MIL) in the combination meter to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs can be accessed using the Techstream.


c.

For details, refer to the Repair Manual.

HINT:
·

The ECM uses the CAN protocol for diagnostic communication. Therefore, a Techstream and a dedicated adapter [CAN VIM (Vehicle Interface Module)] are required for accessing diagnostic data.

·

To clear a DTC that is stored in the ECM, use a Techstream, disconnect the battery terminal or remove the EFI fuse for 1 minute or longer.

·

For details, refer to the Repair Manual.





Fail-safe


a.

General

i.

When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. For details, refer to the Repair Manual.



b.

Fail-safe Operation due to Accelerator Pedal Position Sensor Malfunction

i.

The accelerator pedal position sensor contains two (Main, Sub) sensor circuits.


ii.

If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between these two sensor circuits and switches into a fail-safe mode. In this fail-safe mode, the remaining circuit is used to calculate the accelerator pedal opening, in order to operate the vehicle under fail-safe mode control.

W131835C01
1.5,1.615 1.229,1.333 true 2.844,2.583 2.958,2.354 true 3.865,2.531 3.979,2.302 true 4.531,1.5 4.646,1.833 true 3.271,0.448 3.583,0.604 0.313,0.156 10 false *1 1.031,1.208 1.344,1.365 0.313,0.156 10 false *2 2.76,2.583 3.073,2.74 0.313,0.156 10 false *3 3.771,2.594 4.083,2.75 0.313,0.156 10 false *4 4.396,1.365 4.708,1.521 0.313,0.156 10 false *5 5.51,2.271 5.823,2.427 0.313,0.156 10 false *6 1.635,1.76 1.948,1.917 0.313,0.156 10 false *a 2.094,1.823 2.406,1.979 0.313,0.156 10 false *b 3.031,1.958 3.344,2.115 0.313,0.156 10 false *a 3.063,2.156 3.375,2.313 0.313,0.156 10 false *b 3.875,1.5 4.188,1.656 0.313,0.156 10 false *c 4.135,2.948 4.448,3.104 0.313,0.156 10 false *7
*1 ECM *2 Accelerator Pedal Position Sensor
*3 Throttle Position Sensor *4 Throttle Valve
*5 Return Spring *6 Throttle Control Motor
*7 Throttle Body - -
*a Main *b Sub
*c Open - -



iii.

If both circuits malfunction, the ECM detects the abnormal signal voltage from these two sensor circuits and discontinues throttle control. At this time, the vehicle can be driven using the power generated by the engine at idle.

W131836C01
1.458,1.615 1.177,1.438 true 2.823,2.594 2.917,2.344 true 3.885,2.552 3.979,2.302 true 4.646,1.813 4.521,1.531 true 3.344,0.438 3.656,0.594 0.313,0.156 10 false *1 0.948,1.292 1.26,1.448 0.313,0.156 10 false *2 2.646,2.635 2.958,2.792 0.313,0.156 10 false *3 4.396,1.375 4.708,1.531 0.313,0.156 10 false *5 5.479,2.323 5.792,2.479 0.313,0.156 10 false *6 3.802,2.969 4.115,3.125 0.313,0.156 10 false *7 1.625,1.76 1.938,1.917 0.313,0.156 10 false *a 2.125,1.813 2.438,1.969 0.313,0.156 10 false *b 3.875,1.469 4.188,1.625 0.313,0.156 10 false *c 3.042,1.958 3.354,2.115 0.313,0.156 10 false *a 3.042,2.146 3.354,2.302 0.313,0.156 10 false *b 3.76,2.594 4.073,2.75 0.313,0.156 10 false *4
*1 ECM *2 Accelerator Pedal Position Sensor
*3 Throttle Position Sensor *4 Throttle Valve
*5 Return Spring *6 Throttle Control Motor
*7 Throttle Body - -
*a Main *b Sub
*c Close - -




c.

Fail-safe Operation due to Throttle Position Sensor Malfunction

i.

The throttle position sensor contains two (Main, Sub) sensor circuits.


ii.

If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between these two sensor circuits, cuts off the current to the throttle control motor, and switches to a fail-safe mode.


iii.

Then, the force of the return spring causes the throttle valve to return and stay at its prescribed base opening position. At this time, the vehicle can be driven in the fail-safe mode while the engine output is regulated through control of the fuel injection and ignition timing in accordance with the accelerator pedal position.


iv.

The same control as above is effected if the ECM detects a malfunction in the throttle control motor.

W131837C01
1.438,1.646 1.188,1.396 true 2.792,2.531 2.885,2.333 true 3.802,2.521 3.896,2.323 true 4.49,1.542 4.594,1.75 true 3.24,0.396 3.552,0.552 0.313,0.156 10 false *1 1.667,0.406 1.979,0.563 0.313,0.156 10 false *2 4.885,0.406 5.198,0.563 0.313,0.156 10 false *3 1.021,1.229 1.333,1.385 0.313,0.156 10 false *4 2.646,2.542 2.958,2.698 0.313,0.156 10 false *5 3.708,2.542 4.021,2.698 0.313,0.156 10 false *6 4.385,1.365 4.698,1.521 0.313,0.156 10 false *7 1.552,1.75 1.865,1.906 0.313,0.156 10 false *a 2.073,1.792 2.385,1.948 0.313,0.156 10 false *b 3.844,1.448 4.156,1.604 0.313,0.156 10 false *c 3,1.958 3.313,2.115 0.313,0.156 10 false *a 3,2.135 3.313,2.292 0.313,0.156 10 false *b 5.479,2.271 5.792,2.427 0.313,0.156 10 false *8 4.052,2.948 4.365,3.104 0.313,0.156 10 false *9
*1 ECM *2 Injector
*3 Ignition Coil *4 Accelerator Pedal Position Sensor
*5 Throttle Position Sensor *6 Throttle Valve
*7 Return Spring *8 Throttle Control Motor
*9 Throttle Body - -
*a Main *b Sub
*c Open - -