Home › General › ENGINE › 3UR-FBE ENGINE
NM27M0U _V1 General _050231 ENGINE _0242145 3UR-FBE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FBE ENGINE  GENERAL/CONTROL/DETAILS  INTAKE AND EXHAUST SYSTEM  


General


a.

A linkless-type throttle body is used, achieving excellent throttle control.


b.

The Electronic Throttle Control System-intelligent (ETCS-i) is used to ensure excellent throttle control in all operating ranges.


c.

The Acoustic Control Induction System (ACIS) is used to improve the engine performance in all speed ranges.


d.

A plastic intake manifold is used.


e.

Stainless steel exhaust manifolds and exhaust pipes are used.


f.

Change From 3UR-FE Engine:

i.

The material of the intake manifold gasket has been changed to improve the reliability of the alcohol fuel.

W131853C01
1.198,2.406 0.323,3.438 true 1.51,0.865 1.708,2.323 true 0.604,1.219 1.135,2.042 true 1.427,2.635 0.802,3.865 true 1.844,2.917 1.479,4.25 true 2.885,3.052 3.188,4.229 true 3.448,2.604 4.333,3.896 true 5.125,2.156 6.01,3.448 true 2.917,0.427 2.479,2.708 true 1.396,0.573 1.708,0.729 0.313,0.156 10 false *1 0.458,1.01 0.771,1.167 0.313,0.156 10 false *2 0.188,3.427 0.5,3.583 0.313,0.156 10 false *3 0.688,3.896 1,4.052 0.313,0.156 10 false *4 1.375,4.271 1.688,4.427 0.313,0.156 10 false *5 3.167,4.271 3.479,4.427 0.313,0.156 10 false *6 4.365,3.938 4.677,4.094 0.313,0.156 10 false *7 6.042,3.49 6.354,3.646 0.313,0.156 10 false *8 2.896,0.219 3.208,0.375 0.313,0.156 10 false *9
*1 Intake Manifold *2 Air Cleaner
*3 Throttle Valve *4 Exhaust Manifold RH
*5 Exhaust Manifold LH *6 Front Exhaust Pipe LH
*7 Center Exhaust Pipe *8 Tailpipe
*9 Front Exhaust Pipe RH - -





Air Cleaner


a.

A nonwoven, full-fabric type air cleaner filter element is used.


b.

A carbon filter, which absorbs the HC that accumulates in the intake system when the engine is stopped, is used in the air cleaner case in order to reduce evaporative emissions. This filter is maintenance-free.

W131383C01
2.583,0.573 3.125,0.74 true 2.479,1.458 3.021,1.625 true 2.417,2.24 2.958,2.156 true 2.448,3.135 2.969,2.969 true 2.396,0.448 2.708,0.604 0.313,0.156 10 false *1 2.24,1.365 2.552,1.521 0.313,0.156 10 false *2 2.208,2.177 2.521,2.333 0.313,0.156 10 false *3 2.188,3.177 2.5,3.333 0.313,0.156 10 false *4
*1 Air Cleaner Cap *2 Carbon Filter
*3 Air Cleaner Element (Nonwoven Fabric) *4 Air Cleaner Case




Throttle Body


a.

A linkless-type throttle body, in which the throttle position sensor and the throttle control motor are integrated, is used. It achieves excellent throttle valve control.


b.

For the throttle control motor, a DC motor with excellent response and minimal power consumption is used. The ECM performs duty cycle control of the direction and the amperage of the current supplied to the throttle control motor in order to regulate the throttle valve angle.

W128398C01
4.646,1.125 5.177,0.979 true 3.073,0.688 2.677,0.24 true 3.354,2.219 2.958,2.542 true 2.521,0.104 2.771,0.333 0.25,0.229 10 false *1 2.813,2.5 3.063,2.729 0.25,0.229 10 false *2 5.188,0.875 5.438,1.104 0.25,0.229 10 false *3
*1 Throttle Valve *2 Throttle Control Motor
*3 Throttle Position Sensor Portion - -




Intake Manifold


a.

An intake manifold with a built-in plastic intake air chamber is used for weight reduction.


b.

The port diameter and length has been optimized to achieve high torque in all driving ranges.


c.

The intake manifold contains valves for the Acoustic Control Induction System (ACIS), and the actuator is laser-welded to the intake manifold.

W128399C01
1.708,1.198 1.396,0.573 true 1.771,1.094 1.771,0.51 true 4.26,1.26 4.26,0.677 true 5.563,2.125 5.521,1.49 true 4.5,3.417 4.229,3.063 true 1.26,0.396 1.49,0.625 0.229,0.229 10 false *1 1.708,0.333 1.938,0.563 0.229,0.229 10 false *2 4.198,0.49 4.427,0.719 0.229,0.229 10 false *3 0.302,1.958 0.531,2.188 0.229,0.229 10 false *a 6.698,0.615 6.927,0.844 0.229,0.229 10 false *a 4.5,3.438 4.729,3.667 0.229,0.229 10 false *4 5.51,2.146 5.74,2.375 0.229,0.229 10 false *5
*1 Left Bank Passage *2 Right Bank Passage
*3 ACIS Actuator *4 Laser-welding
*5 Intake Air Control Valve - -
*a Front - -


HINT:
Laser-welding:

In laser-welding, a laser-absorbing material (for the intake manifold) is joined to a laser-transmitting material (for the ACIS actuator). Laser beams are then irradiated from the laser-transmitting side. The beams penetrate the laser-transmitting material to heat and melt the surface of the laser-absorbing material. Then, the heat of the laser-absorbing material melts the laser-transmitting material and causes both materials to become welded.




Exhaust Manifold


a.

A stainless steel exhaust manifold is used for weight reduction and rust resistance.


b.

The exhaust manifold for each bank uses a semi-dual structure (a 4-2-1 grouping). This structure combines the 4 exhaust ports of one bank into 2 groups, then the 2 groups into 1 group, before the exhaust pipe. This reduces exhaust gas interference and improves power output.


c.

The exhaust manifold heat insulator is made of corrugated aluminum. This ensures rigidity, and at the same time, increases the surface area to improve heat dissipation. Furthermore, a floating construction is used in the tightened area to reduce the transfer of heat and vibration to the heat insulator and to improve reliability.


d.

Along with the introduction of the air injection system, air injection pipes are provided for the right and left bank exhaust manifolds.

W128400C01
2,4.563 3.323,3.406 true 1.281,3.031 1.281,2.594 true 3.49,3.135 3.49,1.865 true 4.927,3.823 5.302,2.281 true 5.271,4.063 5.75,3.448 true 5.948,4.438 6.229,4 true 1.448,0.5 1.688,0.719 0.24,0.219 10 false *a 1.469,1.448 1.708,1.667 0.24,0.219 10 false *b 1.219,3.052 1.479,3.281 0.26,0.229 10 false *1 1.823,4.531 2.083,4.76 0.26,0.229 10 false *2 3.438,1.688 3.698,1.917 0.26,0.229 10 false *5 5.26,2.104 5.542,2.354 0.281,0.25 10 false *5 5.729,3.281 5.99,3.51 0.26,0.229 10 false *4 6.208,3.823 6.469,4.052 0.26,0.229 10 false *3 5.625,5.448 5.885,5.677 0.26,0.229 10 false *c 5.625,6.063 5.885,6.292 0.26,0.229 10 false *d
*1 Heat Insulator RH *2 Exhaust Manifold RH
*3 Heat Insulator LH *4 Exhaust Manifold LH
*5 Air Injection Pipe - -
*a Floating Construction *b Heat Insulator Tightened Area Cross Section
*c Corrugated *d Heat Insulator Cross Section




Exhaust Pipe


a.

The exhaust pipes are made of stainless steel to reduce their weight and improve rust resistance.


b.

A 2-way exhaust control system is provided in the muffler.


c.

2 ceramic type TWCs (Three-Way Catalytic converters) are provided in the front exhaust pipe for the right bank and also 2 for the left bank. As a result, exhaust emission performance of the engine is improved.

W131854C01
1.74,1.49 1.552,1.042 true 1.885,2.396 2.26,1.927 true 2.583,2.479 2.635,2.063 true 3.417,2.385 3.25,1.948 true 2.094,1.646 2.021,1.073 true 2.74,1.448 2.792,1 true 4.167,2.156 3.563,1.49 true 5.052,1.917 4.448,1.25 true 5.906,1.552 5.396,1.031 true 4.51,2.01 4.021,1.427 true 1.417,0.823 1.729,0.979 0.313,0.156 10 false *1 1.729,2.427 2.042,2.583 0.313,0.156 10 false *2 2.49,2.552 2.802,2.708 0.313,0.156 10 false *3 4.188,2.188 4.5,2.344 0.313,0.156 10 false *4 4.552,2.052 4.865,2.208 0.313,0.156 10 false *5 5.104,1.969 5.417,2.125 0.313,0.156 10 false *6 5.938,1.594 6.25,1.75 0.313,0.156 10 false *7 3.375,2.479 3.688,2.635 0.313,0.156 10 false *3 1.948,0.875 2.26,1.031 0.313,0.156 10 false *3 2.729,0.771 3.042,0.927 0.313,0.156 10 false *3
*1 Front Exhaust Pipe RH *2 Front Exhaust Pipe LH
*3 TWC *4 Center Exhaust Pipe
*5 Main Muffler *6 Sub Muffler
*7 Exhaust Tailpipe - -