Home › General › ENGINE › 1UR-FE ENGINE
NM27M0U _V1 General _050231 ENGINE _0242147 1UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  1UR-FE ENGINE  GENERAL/CONTROL/DETAILS  INTAKE AND EXHAUST SYSTEM  


General


a.

A linkless-type throttle body is used, thus achieving excellent throttle control.


b.

The Electronic Throttle Control System-intelligent (ETCS-i) is used to ensure excellent throttle control in all operating ranges.


c.

The Acoustic Control Induction System (ACIS) is used to improve engine performance in all speed ranges.


d.

A plastic intake manifold is used.


e.

A step motor type EGR valve and a water-cooled EGR cooler are used in order to improve fuel economy.


f.

Stainless steel exhaust manifolds and exhaust pipes are used.

W131968C01
1.823,1.76 1.479,0.365 true 1.563,1.708 1.073,0.531 true 1,1.552 0.573,0.896 true 0.354,2.781 1.177,1.948 true 0.688,3.229 1.365,2.177 true 1.292,3.49 1.771,2.427 true 3.26,3.406 2.865,2.573 true 4.302,3.208 3.458,2.094 true 2.667,0.25 2.5,2.208 true 6.375,0.323 5.167,1.458 true 0.927,3.406 1.76,2.052 true 1.354,0.156 1.667,0.313 0.313,0.156 10 false *1 0.948,0.333 1.26,0.49 0.313,0.156 10 false *2 0.438,0.719 0.75,0.875 0.313,0.156 10 false *3 0.167,2.802 0.479,2.958 0.313,0.156 10 false *4 0.573,3.229 0.771,3.448 0.198,0.219 10 false *5 0.813,3.406 1.073,3.635 0.26,0.229 10 false *6 1.198,3.49 1.417,3.698 0.219,0.208 10 false *7 3.229,3.417 3.458,3.625 0.229,0.208 10 false *8 4.281,3.208 4.521,3.438 0.24,0.229 10 false *9 6.385,0.188 6.698,0.448 0.313,0.26 10 false *10 2.552,0.063 2.875,0.25 0.323,0.188 10 false *11
*1 Intake Manifold *2 EGR Valve
*3 Air Cleaner *4 Throttle Body
*5 Exhaust Manifold RH *6 EGR Cooler
*7 Exhaust Manifold LH *8 Front Exhaust Pipe LH
*9 Center Exhaust Pipe *10 Tailpipe
*11 Front Exhaust Pipe RH - -




Air Cleaner


a.

A nonwoven, fabric type air cleaner filter element is used.


b.

A carbon filter, which absorbs the HC that accumulates in the intake system when the engine is stopped, is used in the air cleaner case in order to reduce evaporative emissions. This filter is maintenance-free.

W131383C01
2.583,0.573 3.125,0.74 true 2.479,1.458 3.021,1.625 true 2.417,2.24 2.958,2.156 true 2.448,3.135 2.969,2.969 true 2.396,0.448 2.708,0.604 0.313,0.156 10 false *1 2.24,1.365 2.552,1.521 0.313,0.156 10 false *2 2.208,2.177 2.521,2.333 0.313,0.156 10 false *3 2.188,3.177 2.5,3.333 0.313,0.156 10 false *4
*1 Air Cleaner Cap *2 Carbon Filter
*3 Air Cleaner Element (Nonwoven Fabric) *4 Air Cleaner Case




Throttle Body


a.

A linkless-type throttle body, in which the throttle position sensor and the throttle control motor are integrated, is used. It achieves excellent throttle valve control.


b.

For the throttle control motor, a DC motor with excellent response and minimal power consumption is used. The ECM performs duty cycle control of the direction and the amperage of the current supplied to the throttle control motor in order to regulate the throttle valve angle.

W131969C01
3.135,0.875 2.802,0.333 true 3.458,2.552 3.688,2.094 true 4.563,1.125 4.958,0.906 true 2.656,0.115 2.969,0.271 0.313,0.156 10 false *1 3.333,2.583 3.646,2.74 0.313,0.156 10 false *2 5.031,0.823 5.344,0.979 0.313,0.156 10 false *3
*1 Throttle Valve *2 Throttle Control Motor (DC Motor)
*3 Throttle Position Sensor Portion - -




Intake Manifold


a.

An intake manifold with a built-in plastic intake air chamber is used for weight reduction.


b.

The diameter and length of the port have been optimized to achieve high torque in all driving ranges.


c.

The intake manifold contains valves for the Acoustic Control Induction System (ACIS), and the actuator is laser-welded to the intake manifold.

W131970C01
1.594,1.281 1.302,0.865 true 1.854,1.146 1.677,0.667 true 4.115,1.396 3.938,0.917 true 5.896,2.104 5.385,1.438 true 4.385,3.344 4.146,3.094 true 3.802,0.708 4.115,0.865 0.313,0.156 10 false *1 5.906,2.156 6.219,2.313 0.313,0.156 10 false *2 4.438,3.385 4.75,3.542 0.313,0.156 10 false *d 1.146,0.646 1.458,0.802 0.313,0.156 10 false *a 6.729,0.583 7.042,0.74 0.313,0.156 10 false *c 1.521,0.438 1.833,0.594 0.313,0.156 10 false *b 0.302,2.063 0.615,2.219 0.313,0.156 10 false *c
*1 ACIS Actuator *2 Intake Air Control Valve
*a Left Bank Passage *b Right Bank Passage
*c Front *d Laser-welding


HINT:
Laser-welding:

In laser-welding, a laser-absorbing material (for the intake manifold) is joined to a laser-transmitting material (for the ACIS actuator). Laser beams are then irradiated from the laser-transmitting side. The beams penetrate the laser-transmitting material to heat and melt the surface of the laser-absorbing material. Then, the heat of the laser-absorbing material melts the laser-transmitting material and causes both materials to become welded.




EGR Valve


a.

A step motor is used on the EGR valve to enable the ECM to directly control the EGR valve.


b.

The water circulates through the EGR valve to ensure proper cooling performance.

W131971C01
3.833,0.135 6.365,3.625 2.531,3.49 6.073,2.156 6.385,2.313 0.313,0.156 10 false *e 1.448,3.094 1.76,3.25 0.313,0.156 10 false *a 3.469,2.875 3.781,3.031 0.313,0.156 10 false *b 3.906,0.219 4.219,0.375 0.313,0.156 10 false *c 4.917,3.406 5.229,3.563 0.313,0.156 10 false *d
*a Engine Coolant Out *b Engine Coolant In
*c EGR Valve Cross Section *d Exhaust Gas In (From EGR Cooler)
*e Exhaust Gas Out (To Intake Manifold) - -




EGR Cooler


a.

The water-cooled type EGR cooler is used in the EGR passage between the cylinder head and EGR valve.


b.

In the water-cooled type EGR cooler, engine coolant flows to the 4-layered gas passage to cool down.

W131972C01
1.958,2.219 1.188,1.604 true 2.771,3.292 2.583,2.24 true 3.615,3.323 2.885,2.052 true 3.927,1.688 3.063,1.698 true 2.917,1.521 2.354,0.458 true 6.292,1.729 5.927,1.427 true 4.875,2.469 4.708,2.323 true 4.896,2.823 4.563,2.771 true 1.021,1.448 1.333,1.604 0.313,0.156 10 false *a 3.646,3.385 3.958,3.542 0.313,0.156 10 false *b 3.979,1.604 4.292,1.76 0.313,0.156 10 false *c 2.219,0.229 2.531,0.385 0.313,0.156 10 false *d 4.563,2.135 4.875,2.292 0.313,0.156 10 false *e 2.719,3.333 3.031,3.49 0.313,0.156 10 false *1 4.802,1.021 5.073,1.25 0.271,0.229 10 false A 6.104,1.302 6.375,1.531 0.271,0.229 10 false A 5.854,0.49 6.167,0.646 0.313,0.156 10 false *d 6.198,0.813 6.51,0.969 0.313,0.156 10 false *c 4.583,1.896 4.896,2.052 0.313,0.156 10 false *a 6.344,1.719 6.656,1.875 0.313,0.156 10 false *b 4.375,2.667 4.688,2.823 0.313,0.156 10 false *f 5.323,3.229 5.635,3.385 0.313,0.156 10 false *g
*1 EGR Cooler - -
*a Exhaust Gas In *b Engine Coolant In
*c Engine Coolant Out *d Exhaust Gas Out
*e Engine Coolant *f Exhaust Gas
*g A - A Cross Section - -




Exhaust Manifold


a.

A stainless steel exhaust manifold is used for weight reduction and rust resistance.


b.

The exhaust manifold for each bank uses a single structure (in a 4-1 grouping).


c.

The exhaust manifold heat insulator is made of corrugated aluminum. This ensures rigidity, and at the same time, increases the surface area to improve heat dissipation. Furthermore, a floating construction is used in the tightened area to reduce the transfer of heat and vibration to the heat insulator and to improve reliability.


d.

Along with the use of the air injection system, air injection pipes are provided for the right and left bank exhaust manifolds.

W131973C01
0.938,2.948 1.354,2.531 true 2.125,4.448 3.052,3.552 true 5.948,4.396 6.479,3.979 true 3.729,3.198 4.177,1.896 true 5.656,3.719 5.135,3.729 true 3.677,5.313 4.313,4.031 true 0.74,2.958 1.052,3.115 0.313,0.156 10 false *1 1.958,4.521 2.271,4.677 0.313,0.156 10 false *2 3.542,5.365 3.854,5.521 0.313,0.156 10 false *3 6.542,3.865 6.854,4.021 0.313,0.156 10 false *4 0.781,0.573 1.094,0.729 0.313,0.156 10 false *a 1.542,0.74 1.854,0.896 0.313,0.156 10 false *b 4.75,4.99 5.063,5.146 0.313,0.156 10 false *c 5.458,5.385 5.771,5.542 0.313,0.156 10 false *d 5.75,3.656 6.063,3.813 0.313,0.156 10 false *5 4.156,1.688 4.469,1.844 0.313,0.156 10 false *5
*1 Heat Insulator RH *2 Exhaust Manifold RH
*3 Exhaust Manifold LH *4 Heat Insulator LH
*5 Air Injection Pipe - -
*a Heat Insulator Tightened Area Cross Section *b Floating Construction
*c Heat Insulator Cross Section *d Corrugated




Exhaust Pipe


a.

The exhaust pipes are made of stainless steel to reduce their weight and improve rust resistance.


b.

2 ceramic type Three-Way Catalytic converters (TWCs) are provided in the front exhaust pipe for the right bank, and another 2 are also provided for the left bank. As a result, the exhaust emission performance of the engine is improved.

W131854C01
1.74,1.49 1.552,1.042 true 1.885,2.396 2.26,1.927 true 2.583,2.479 2.635,2.063 true 3.417,2.385 3.25,1.948 true 2.094,1.646 2.021,1.073 true 2.74,1.448 2.792,1 true 4.167,2.156 3.563,1.49 true 5.052,1.917 4.448,1.25 true 5.906,1.552 5.396,1.031 true 4.51,2.01 4.021,1.427 true 1.417,0.823 1.729,0.979 0.313,0.156 10 false *1 1.729,2.427 2.042,2.583 0.313,0.156 10 false *2 2.49,2.552 2.802,2.708 0.313,0.156 10 false *3 4.188,2.188 4.5,2.344 0.313,0.156 10 false *4 4.552,2.052 4.865,2.208 0.313,0.156 10 false *5 5.104,1.969 5.417,2.125 0.313,0.156 10 false *6 5.938,1.594 6.25,1.75 0.313,0.156 10 false *7 3.375,2.479 3.688,2.635 0.313,0.156 10 false *3 1.948,0.875 2.26,1.031 0.313,0.156 10 false *3 2.729,0.771 3.042,0.927 0.313,0.156 10 false *3
*1 Front Exhaust Pipe RH *2 Front Exhaust Pipe LH
*3 TWC *4 Center Exhaust Pipe
*5 Main Muffler *6 Sub Muffler
*7 Tailpipe - -