General
The electronic control system of the A760E and A760F automatic transmissions consists of the control functions listed below:
| Control | Function |
|---|---|
| Shift Timing Control | The ECM sends current to shift solenoid valves S1, S2, S3, S4 and/or SR based on signals from various sensors, in order to shift the gears. |
| Clutch Pressure Control | ·
Controls the pressure applied directly to B2 brake and C3 clutch by actuating the shift solenoid valves SL1 and SL2 in accordance with the ECM signals. ·
The shift solenoid valves SLT and SL1 minutely control the clutch pressure in accordance with the engine output and driving conditions. |
| Line Pressure Optimal Contro | Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission. |
| Engine Torque Control | Retards the engine ignition timing temporarily to improve shift feeling while upshifting or downshifting occurs. |
| Lock-up Timing Control | The ECM sends current to the shift solenoid valve SLU based on signals from various sensors and engages or disengages the lock-up clutch. |
| Flex Lock-up Clutch Control | Controls the shift solenoid valve SLU, provides an intermediate mode for when the lock-up clutch is between on and off, and increases the operating range of the lock-up clutch to improve fuel economy. |
| Powertrain Cooperative Control | Controls both the shift control and engine output control in an integrated way, achieving excellent shift characteristics and driveability. |
| Coast Downshift Control | To prevent engine speed from decreasing and thus maintain the fuel cut, the ECM performs downshifting before the fuel cut ends. |
| Artificial Intelligence-shift (AI-shift) Control | Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, thus improving driveability. |
| Multi-mode Automatic Transmission | The ECM appropriately controls the automatic transmission in accordance with the range position selected while the shift lever is in S. |
| Diagnosis | When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information that relates to the fault. |
| Fail-safe | If a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's driveability from being affected significantly. |
Construction
The configurations of the electronic control system for the A760E and A760F automatic transmissions are as shown in the following chart:
Layout of Main Components
| *1 | ECM | *2 | Shift Solenoid Valve S1 |
| *3 | Shift Solenoid Valve SR | *4 | Shift Solenoid Valve SL1 |
| *5 | Shift Solenoid Valve SLT | *6 | ATF TemperatureSensor No. 1 |
| *7 | ATF Temperature Sensor No. 2 | *8 | Input Speed Sensor |
| *9 | Shift Solenoid Valve SL2 | *10 | Shift SolenoidValve SLU |
| *11 | Shift Solenoid Valve S3 | *12 | Shift Solenoid Valve S2 |
| *13 | Shift Solenoid Valve S4 | *14 | Output Speed Sensor |
| *15 | Park/Neutral Position Switch | - | - |
| *1 | Combination Meter | *2 | DLC3 |
| *3 | Stop Light Switch | *4 | Accelerator Pedal Position Switch |
| *5 | Shift Lever Assembly (Floor Shift)
·
Transmission Control Switch ·
Shift Lock ECU |
*6 | Shift Lever Assembly (Column Shift)
·
Transmission Control Switch |
Construction and Operation of Main Components
ATF Temperature Sensors No. 1 and No. 2
The ATF temperature sensor No. 1 (THO1) is used for hydraulic pressure control. This sensor is used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.
The ATF temperature sensor No. 2 (THO2) is used as a basis for modifying the ECT shift timing control when the ATF temperature is high. It is also used for the ATF temperature warning light.
| *1 | ATF Temperature Sensor No. 1 (THO1) | *2 | ATF Temperature Sensor No. 2 (THO2) |
| *a | Front | - | - |
Input Speed Sensor and Output Speed Sensor
The A760E and A760F automatic transmissions use an input speed sensor (for NT signal) and an output speed sensor (for SP2 signal). Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions. These speed sensors are the pick-up coil type.
The input speed sensor detects the input speed of the transmission. The No. 3 clutch (C3) drum is used as the timing rotor for this sensor.
The output speed sensor detects the speed of the output shaft. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
| *1 | No. 3 Clutch (C3) Drum | *2 | Input Speed Sensor (NT) |
| *3 | Parking Gear (Timing Rotor) | *4 | Output Speed Sensor (SP2) |
Park/Neutral Position Switch
The park/neutral position switch sends the P, R, N, D and NSW position signals to the ECM. It also sends signals for the shift position indicator light (P, R, N, and D).
Transmission Control Switch
The transmission control switch is installed inside the shift lever assembly to detect the shift lever position and to inform the ECM. The ECM turns on the shift position indicator light and S mode indicator light.
The transmission control switch detects whether the shift lever is in D or S, detects the operating conditions of the shift lever ("+"or "-") if S mode is selected, and sends signals to the ECM. At this time, the ECM turns on the shift range indicator for the selected range.
Clutch Pressure Control
Clutch to Clutch Pressure Control
This control is used for shifting from 5th to 6th gear and from 6th to 5th gear.
The ECM actuates shift solenoid valves SL1 and SL2 in accordance with various signals. The output from these shift solenoid valves acts directly on control valves B2 and C3 in order to regulate the line pressure that acts on the No. 2 brake (B2) and No. 3 clutch (C3). As a result, high response and excellent shift characteristics have been achieved.
Clutch Pressure Optimal Control
The ECM monitors the signals from various types of sensors, such as the input speed sensor, allowing shift solenoid valves SLT, SL1 and SL2 to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are achieved.
Line Pressure Optimal Control
Through the use of the shift solenoid valve SLT, the line pressure is optimally controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter clutch and the transmission.
Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition, and ATF temperature, thus achieving smooth shift characteristics and optimizing the workload of the oil pump (reducing unnecessary parasitic losses).
Lock-up Timing Control
The ECM operates the lock-up timing control in order to improve the fuel consumption performance while in top gear with the shift lever in the S4 or S5 range, and in 5th or 6th gear with the shift lever in the S6 range or D.
| Shift Position or Shift Range | D, S6 | S5 | S4 | |
|---|---|---|---|---|
|
○: Available X: Not available -: Not applicable *: Lock-up operation is performed when the 4th gear is held during the AI-shift control or the cruise control. |
||||
| Gear | 1st | X | X | X |
| 2nd | X | X | X | |
| 3rd | X | X | X | |
| 4th | X* | X* | ○ | |
| 5th | ○ | ○ | - | |
| 6th | ○ | - | - | |
Flex Lock-up Clutch Control
In the low-to-mid-speed range, the flex lock-up clutch control regulates the shift solenoid valve SLU to provide an intermediate mode between the on and off operation of the lock-up clutch in order to improve energy transmitting efficiency.
As a result, the operating range of the lock-up clutch has been increased and fuel economy has been improved. The flex lock-up clutch control operates in the 3rd, 4th, 5th and 6th gears in D and S6 range, in the 3rd, 4th and 5th gears in the S5 range, and in the 3rd and 4th gears in the S4 range.
Even when the vehicle is decelerating (the accelerator pedal is released), the flex lock-up clutch control operates. Therefore, the fuel cut area of the engine has been expanded and fuel economy has been improved.
| Shift Position or Shift Range | D, S6 | S5 | S4 | |
|---|---|---|---|---|
|
○: Available X: Not available -: Not applicable *1: Only flex lock-up operates when the vehicle is accelerating *2: Only flex lock-up operates when the vehicle is decelerating |
||||
| Gear | 1st | X | X | X |
| 2nd | X | X | X | |
| 3rd | ○*1 | ○*1 | ○*1 | |
| 4th | ○ | ○ | ○ | |
| 5th | ○ | ○ | - | |
| 6th | ○*2 | - | - | |
Powertrain Cooperative Control
Through cooperative control with Electronic Throttle Control System-intelligent (ETCS-i) and Electronic Spark Advance (ESA), and electronic control of the engagement and release speed of the clutch and brake hydraulic pressures, excellent response and shift shock reduction have been achieved.
Coast Downshift Control
As a result of coast downshift control, downshifting is performed to maintain sufficient engine speed to avoid ending fuel cut control. Thus, fuel cut time is extended and fuel economy is achieved.
In this control, the transmission downshifts from 6th to 5th and then 5th to 4th before fuel cut control ends when the vehicle is decelerated in the 6th gear, so that fuel cut control can continue to operate.
Artificial Intelligence-shift (AI-shift) Control
General
The AI-shift control determines optimal transmission control based on input signals and automatically changes the shift pattern. As a result, a high caliber of transmission operation is achieved.
The AI-shift control includes a road condition support control and a driver's intention support control.
The AI-shift control is effected only with the shift lever in D, based on the accelerator pedal and brake operation data. The AI-shift control will be canceled when the driver selects the S mode.
Road Condition Support Control
Under road condition support control, the ECM identifies the throttle valve opening angle and the vehicle speed to determine whether the vehicle is being driven uphill or downhill.
To achieve an optimal drive force while driving uphill, this control prevents the transmission from upshifting to 4th, 5th or 6th gear.
To achieve an optimal engine braking effect while driving downhill, this control automatically downshifts the transmission to 5th, 4th or 3rd gear.
Driver's Intention Support Control
The driver's intention support control estimates the driver's intention based on the accelerator pedal operation and vehicle condition, and selects a shift pattern that is well-suited to the driver.
Multi-mode Automatic Transmission
General
Multi-mode automatic transmission is designed to allow the driver to switch the gear ranges (multi-mode transmission is not for manually selecting single gears). After moving the shift lever to S, the driver can select the desired shift range by moving the shift lever to "+" or "-". Thus, the driver is able to shift gears with a manual-like feel.
Operation
Column Shift
The driver selects the S mode by engaging the shift lever. At this time, the S4 or S5 range is selected in accordance with the vehicle speed. (When the driver selects the S mode during AI-shift control, the current gear will be selected as the shift range.) Then, the shift range changes one at a time, as the driver moves the transmission control switch forward ("+") or backward ("-").
Under the multi-mode automatic transmission control, the ECM effects optimal shift control within the usable gear range that the driver has selected. The 1st gear is shifted to when the vehicle is stopped.
Holding the transmission control switch in "+" with the shift lever in S will change the shift range to the S6 range regardless of range (S1 to S5).
When the shift lever is in S, the S mode indicator light in the combination meter illuminates. The shift range indicator indicates the shift range position that the driver has selected.
| Shift Range | Shift Range Indicator Display | Usable Gears |
|---|---|---|
| S6 | 6 | 6th←→5th←→4th←→3rd←→2nd←→1st |
| S5 | 5 | 5th←→4th←→3rd←→2nd←→1st |
| S4 | 4 | 4th←→3rd←→2nd←→1st |
| S3 | 3 | 3rd←→2nd←→1st |
| S2 | 2 | 2nd←→1st |
| S1 | 1 | 1st |
Floor Shift
The driver selects the S mode by engaging the shift lever. At this time, the S4 or S5 range is selected in accordance with the vehicle speed. (When the driver selects the S mode during AI-shift control, the current gear will be selected as the shift range.) Then, the shift range changes one at a time, as the driver moves the shift lever forward ("+") or backward ("-").
Under this control, the ECM effects optimal shift control within the usable gear range that the driver has selected. The 1st gear is shifted to when the vehicle is stopped.
Holding the shift lever forward ("+") will change the shift range to the S6 range regardless of range (S1 to S5).
When the shift lever is in S, the S mode indicator light in the combination meter illuminates. The shift range indicator indicates the shift range position that the driver has selected.
| Shift Range | Shift Range Indicator Display | Usable Gears |
|---|---|---|
| S6 | 6 | 6th←→5th←→4th←→3rd←→2nd←→1st |
| S5 | 5 | 5th←→4th←→3rd←→2nd←→1st |
| S4 | 4 | 4th←→3rd←→2nd←→1st |
| S3 | 3 | 3rd←→2nd←→1st |
| S2 | 2 | 2nd←→1st |
| S1 | 1 | 1st |
Diagnosis
When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the Malfunction Indicator Lamp (MIL) in the combination meter illuminates or blinks to inform the driver.
The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs can be accessed using the Techstream.
For details, refer to the Repair Manual.
Fail-safe
The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a shift solenoid valve.
| Malfunction Part | Function |
|---|---|
| Input Speed Sensor (NT) | When the input speed sensor malfunctions, shift control is effected using the information from the output speed sensor signal (SP2). During an input speed sensor malfunction, upshifting to the 5th and 6th, AI-shift and flex lock-up clutch control are prohibited. |
| Output Speed Sensor (SP2) | When the output speed sensor malfunctions, shift control is effected using the information from the input speed sensor signal (NT). When the output speed sensor malfunctions, upshifting to the 5th and 6th, AI-shift and flex lock-up clutch control are prohibited. |
| ATF Temperature Sensor No. 1 (THO1) | When the ATF temperature sensor No. 1 malfunctions, upshifting to the 5th and 6th and flex lock-up clutch control are prohibited. |
| Shift Solenoid Valves S1, S2, S3, S4 and SR | When a shift solenoid valve listed at left fails, the current to the failed shift solenoid valve is cut off. Shift control is changed to a fail-safe mode to shift gears using the normal shift solenoid valves to allow for continued driving. Refer to the table on the next page for an operation example. |
| Shift Solenoid Valves SL1 and SL2 | During a shift solenoid valve SL1 or SL2 malfunction, upshifting to the 5th and 6th and flex lock-up clutch control are prohibited. |
| Shift Solenoid Valve SLU | During a shift solenoid valve SLU malfunction, the current to the shift solenoid valve is stopped. Because this stops the lock-up control and flex lock-up control, fuel economy decreases. |
| Shift Solenoid Valve SLT | During a shift solenoid valve SLT malfunction, the current to the shift solenoid valve is stopped. Because this stops the line pressure optimal control, the shift shock increases. However, shifting is effected through normal clutch pressure control. |
| Shift Position or Range | Shift Solenoid Valve | Gear | ||||||
|---|---|---|---|---|---|---|---|---|
| S1 | S2 | S3 | S4 | SR | SL1 | SL2 | ||
| D, S6 | Off | On | On | Off | On | Off | On | 1st |
| On | On | On | Off | On | Off | On | 2nd | |
| On | Off | On | Off | On | Off | On | 3rd | |
| On | Off | Off | Off | On | Off | On | 4th | |
| On | Off | Off | On | Off | On | Off | 5th | |
| On | On | Off | On | Off | On | Off | 6th | |
| S5 | Off | On | On | Off | On | Off | On | 1st |
| On | On | On | Off | On | Off | On | 2nd | |
| On | Off | On | Off | On | Off | On | 3rd | |
| On | Off | Off | Off | On | Off | On | 4th | |
| On | Off | Off | On | Off | On | Off | 5th | |
| S4 | Off | On | On | Off | On | Off | On | 1st |
| On | On | On | Off | On | Off | On | 2nd | |
| On | Off | On | Off | On | Off | On | 3rd | |
| On | Off | Off | Off | On | Off | On | 4th | |
| S3 | Off | On | On | Off | On | Off | On | 1st |
| On | On | On | Off | On | Off | On | 2nd | |
| On | Off | On | Off | On | Off | Off | 3rd | |
| S2 | Off | On | On | Off | On | Off | On | 1st |
| On | On | On | On | On | Off | Off | 2nd | |
| S1 | Off | On | On | Off | On | Off | Off | 1st |
| Shift Position or Range | Shift Solenoid Valve | Gear | ||||||
|---|---|---|---|---|---|---|---|---|
| S1 | S2 | S3 | S4 | SR | SL1 | SL2 | ||
|
E/B: Engine Braking |
||||||||
| D, S6 | X | On | On | Off | On | Off | On | 1st |
| X | On → Off | On → Off | Off | On | Off | On | 1st → 4th | |
| X | Off | On → Off | Off | On | Off | On | 3rd → 4th | |
| X | Off | Off | Off | On | Off | On | 4th | |
| X | Off | Off | On | Off | On | Off | 5th | |
| X | On → Off | Off | On | Off | On | Off | N → 5th | |
| S5 | X | On | On | Off | On | Off | On | 1st |
| X | On → Off | On → Off | Off | On | Off | On | 1st → 4th | |
| X | Off | On → Off | Off | On | Off | On | 3rd → 4th | |
| X | Off | Off | Off | On | Off | On | 4th | |
| X | Off | Off | On | Off | On | Off | 5th | |
| S4 | X | On | On | Off | On | Off | On | 1st |
| X | On → Off | On → Off | Off | On | Off | On | 1st → 4th | |
| X | Off | On → Off | Off | On | Off | On | 3rd → 4th | |
| X | Off | Off | Off | On | Off | On | 4th | |
| S3 | X | On | On | Off | On | Off | On | 1st |
| X | On → Off | On → Off | Off | On | Off | On | 1st → 4th | |
| X | Off | On → Off | Off | On | Off | Off → On | 3rd (E/B) → 4th | |
| S2 | X | On | On | Off | On | Off | On | 1th |
| X | On → Off | On → Off | On → Off | On | Off | Off → On | 3rd (E/B) → 4th | |
| S1 | X | On | On | Off | On | Off | Off | 1st (E/B) |