Home › General › CHASSIS › BRAKE
NM27M0U _V1 General _050232 CHASSIS _0242206 BRAKE UN GENERAL/CONTROL/DETAILS F

CHASSIS  BRAKE  GENERAL/CONTROL/DETAILS  BRAKE CONTROL SYSTEM  


General


a.

The brake control system has the following functions:

Function Outline Model
2WD 4WD
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. ○ ○
Electronic Brake force Distribution (EBD) The EBD control utilizes the ABS, realizing the proper brake force distribution between front and rear wheels in accordance with the driving conditions.
In addition, during braking while cornering, it also controls the brake forces of right and left wheels, helping maintain the vehicle behavior.
○ ○
Brake Assist
·

The primary purpose of brake assist is to provide a supplementary braking force to assist a driver who cannot generate a large brake force during emergency braking, thus helping improve the vehicle's braking performance.

·

If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


○ ○
Traction Control (TRAC) TRAC helps prevent the drive wheels from slipping if the driver presses the accelerator pedal excessively when starting off or accelerating on a slippery surface. ○ ○*1
Active Traction Control (A-TRAC)*2 When the vehicle drive mode is 4H or 4L, the A-TRAC operates. A-TRAC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an Limited Slip Differential (LSD) effect. - ○
Limited Slip Differential (Auto LSD) Briefly pressing the VSC OFF switch in normal mode enters TRAC OFF mode, allowing the auto LSD system to operate. The auto LSD system achieves a function equivalent to that of an LSD system through the use of the TRAC. The auto LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel. ○ ○*1
Vehicle Stability Control (VSC) VSC helps prevent the vehicle from slipping sideways as a result of strong front wheel skid or strong rear wheel skid during unstable situation (VSC operates when the vehicle speed is 15 km/h or more). ○ ○
Trailer Sway Control If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the motive force output in order to suppress trailer sway. ○ ○

HINT:

*1: For 4WD models, these functions operate while in 2WD mode.

*2: This function only uses brakes to perform traction control.




Drive Modes


a.

Drive Modes and Each Function

i.

The functions of the various drive modes are shown in the following table:

2WD Models
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode Auto LSD Mode VSC OFF Mode
ABS ○ ○ ○ ○
EBD ○ ○ ○ ○
Brake Assist ○ ○ ○ ○
TRAC ○ X X X
Auto LSD X ○ ○ X
VSC ○ ○ X X
Trailer Sway Control ○ ○ X X

HINT:

○ : Controlled

X: Not controlled


4WD Models (Drive Mode: 2WD)
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode Auto LSD Mode VSC OFF Mode
ABS ○ ○ ○ ○
EBD ○ ○ ○ ○
Brake Assist ○ ○ ○ ○
TRAC ○ X X X
A-TRAC X X X X
Auto LSD X ○ ○ X
VSC ○ ○ X X
Trailer Sway Control ○ ○ X X

HINT:

○ : Controlled

X: Not controlled


4WD Models [Drive Mode: 4WD (4H)]
Brake Control VSC OFF Switch
Normal Mode TRAC OFF Mode VSC OFF Mode
ABS ○ ○ ○
EBD ○ ○ ○
Brake Assist ○ ○ ○
TRAC X X X
A-TRAC ○ X X
Auto LSD X X X
VSC ○ ○ X
Trailer Sway Control ○ ○ X

HINT:

○ : Controlled

X: Not controlled


4WD Models [Drive Mode: 4WD (4L)]
Brake Control VSC OFF Switch
Normal Mode VSC OFF Mode
ABS ○ ○
EBD ○ ○
Brake Assist ○ ○
TRAC X X
A-TRAC ○ X
Auto LSD X X
VSC X X
Trailer Sway Control X X

HINT:

○ : Controlled

X: Not controlled





System Diagram


X131010E01
0.365,0.198 2.094,0.542 1.729,0.344 10 false Front Speed Sensor RH 0.344,0.75 2.083,1.094 1.74,0.344 10 false Front Speed Sensor LH 0.385,1.323 2.021,1.646 1.635,0.323 10 false Rear Speed Sensor RH 0.458,1.865 2.135,2.208 1.677,0.344 10 false Rear Speed Sensor LH 0.688,2.417 2.042,2.74 1.354,0.323 10 false VSC OFF Switch 0.458,2.979 2.125,3.323 1.667,0.344 10 false Parking Brake Switch 0.406,3.531 2.104,3.833 1.698,0.302 10 false A.D.D. Detection Switch 0.125,4.073 2.302,4.448 2.177,0.375 10 false Yaw Rate and Deceleration Sensor 0.677,4.635 1.927,4.99 1.25,0.354 10 false Stop Light Switch 0.75,5.188 1.979,5.563 1.229,0.375 10 false BRK NO. 1 Relay 0.698,5.76 2.083,6.125 1.385,0.365 10 false BRK NO. 2 Relay 1.104,6.594 2.094,6.938 0.99,0.344 10 false Stop Light 2.604,6.406 3.552,6.854 0.948,0.448 10 false CAN (V Bus) 1.052,7.177 1.677,7.521 0.625,0.344 10 false ECM 0.646,7.813 2.063,8.156 1.417,0.344 10 false 4WD Control ECU* 0.115,8.354 1.719,8.677 1.604,0.323 10 false *: 4WD models 4.979,7.823 6.99,8.198 2.01,0.375 10 false Combination Meter Assembly 5.177,7.188 6.802,7.563 1.625,0.375 10 false Steering Angle Sensor 5.74,6.563 6.448,6.917 0.708,0.354 10 false DLC3 5.188,5.896 6.813,6.219 1.625,0.323 10 false Booster Stroke Sensor 5.573,5.427 6.708,5.75 1.135,0.323 10 false Micro Switch 5.385,4.948 6.792,5.281 1.406,0.333 10 false Booster Solenoid 5.458,4.479 6.573,4.792 1.115,0.313 10 false Brake Booster 5.115,4 6.24,4.333 1.125,0.333 10 false Brake Actuator 3.208,2.563 4.063,2.896 0.854,0.333 10 false Motor Relay 5.438,3.031 6.583,3.781 1.146,0.75 10 false Master Cylinder Pressure Sensor 5.563,2.573 6.5,2.896 0.938,0.323 10 false Pump Motor 5.344,2.083 6.698,2.406 1.354,0.323 10 false Solenoid Valves (8) 5.24,1.219 6.677,1.969 1.438,0.75 10 false Reservoir Cut Solenoid Valves (2) 5.313,0.344 6.615,1.094 1.302,0.75 10 false Master Cylinder Cut Solenoid Valves (2) 3.302,0.49 3.969,1.208 0.667,0.719 10 false Solenoid Relay 3.052,1.719 4.208,2.208 1.156,0.49 10 false Skid Control ECU


Outline of EBD Control


a.

General

i.

The EBD control distributes the braking force in accordance with the vehicle's driving conditions. The skid control ECU electrically controls the control solenoid valves to distribute the braking force.

·

Braking force distribution is divided into two main categories: one is to the front and rear wheels, and the other is to the right to left sides (braking while cornering).




b.

Front/Rear Wheel Brake Force Distribution

i.

If the brakes are applied while the vehicle is moving straight forward, the transfer of the load reduces the weight that is applied to the rear wheels. The skid control ECU determines this condition by way of the signals from the speed sensors, and the brake actuator regulates the distribution of the brake force of the rear wheels to optimally control braking operation.


ii.

For example, the amount of the brake force that is applied to the rear wheels during braking varies whether or not the vehicle is carrying a load. The amount of the brake force that is applied to the rear wheels also varies in accordance with the extent of the deceleration.


iii.

Thus, the distribution of the brake force to the rear is optimally controlled in order to effectively utilize the braking force of the rear wheels under these conditions.

X105300E02
2.365,2.531 2.156,2.531 2.156,2.531 2.156,2.344 true 1.833,1.563 1.469,1.563 1.469,1.563 1.698,2.406 true 5.188,2.521 4.979,2.521 4.979,2.521 4.979,2.333 true 4.688,1.448 4.323,1.448 4.323,1.448 4.719,2.177 true 0.323,2.052 1.031,2.823 0.708,0.771 10 false Rear Brake Force 3.354,2.01 4.073,2.781 0.719,0.771 10 false Rear Brake Force 1.875,1.438 3.802,1.813 1.927,0.375 10 false Ideal Brake Force Distribution 2.417,2.427 3.635,2.823 1.219,0.396 10 false EBD Control 1.49,2.885 2.813,3.271 1.323,0.385 10 false Front Brake Force 1.438,3.323 3.042,3.708 1.604,0.385 10 false Without Load in Rear 4.531,2.875 5.854,3.26 1.323,0.385 10 false Front Brake Force 4.531,3.292 6.135,3.677 1.604,0.385 10 false With Load in Rear 4.75,1.354 6.708,1.75 1.958,0.396 10 false Ideal Brake Force Distribution 5.25,2.417 6.469,2.813 1.219,0.396 10 false EBD Control




Outline of Brake Assist


a.

The brake assist, in combination with ABS, helps improve the vehicle's braking performance.


b.

The brake assist interprets a quick push of the brake pedal as emergency braking. It supplements the brake power applied if the driver has not stepped hard enough on the brake pedal. In emergencies, drivers, especially inexperienced ones, often panic and do not apply sufficient pressure to the brake pedal.


c.

A key feature of brake assist is that the timing and the degree of braking assistance are designed to help ensure that the driver does not discern anything unusual about the braking operation. When the driver intentionally eases up on the brake pedal, the brake assist reduces the amount of assistance it provides.


d.

Based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed and the amount of the brake pedal application and then determines the intention of the driver to perform emergency braking. If the skid control ECU determines that the driver intends emergency braking, the system activates the brake actuator to increase the brake fluid pressure, which increases the braking force.


e.

When the vehicle is fully loaded, stronger brake force may be required, even if the brakes are not applied quickly. In such a case where stronger brake force is required, the brake assist also increases brake force.

In case that the driver's pedal application force is small when applying emergency braking
X128261E01
1.688,1.51 2.969,0.698 2.969,0.698 3.125,0.698 false 0.083,0.583 1.115,1.281 1.031,0.698 10 false Master Cylinder Pressure Sensor Signal 3.188,0.615 5.146,1.333 1.958,0.719 10 false The fluid pressure is increased by brake actuator. 1.385,0.542 2.24,0.979 0.854,0.438 10 false Skid Control ECU 4.719,3.302 6.146,3.615 1.427,0.313 10 false Without Brake Assist 1.396,3.271 2.635,3.729 1.24,0.458 10 false With Brake Assist 0.302,3.938 6.938,4.323 6.635,0.385 10 false There is no difference of the maximum brake performance between the vehicles with and without brake assist. 0.417,6.042 1.25,6.469 0.833,0.427 10 false Brake Force 3.521,8.302 4,8.625 0.479,0.323 10 false Time 3.01,5.385 4.323,5.781 1.313,0.396 10 false With Brake Assist 3.01,6.5 4.375,6.854 1.365,0.354 10 false Without Brake Assist



Outline of TRAC


a.

If the driver presses the accelerator pedal aggressively when initially accelerating or when accelerating on a slippery surface, the drive wheels could slip due to the excessive amount of torque that is generated. By applying hydraulic brake control to the drive wheels and regulating the throttle to control the engine output, TRAC helps minimize the slippage of the drive wheels, thus helping to apply the drive force that is appropriate for the road surface conditions.


b.

For example, a comparison may be made between two vehicles, one with TRAC and the other without. If the driver of each vehicle operates the accelerator pedal in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle can not start accelerating smoothly.


c.

However, when the vehicle is equipped with TRAC, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply the brakes to the slipping drive wheel. Furthermore, the ECM receives the signals from the skid control ECU and regulates the throttle in order to control the engine output. Thus, TRAC can constantly help the driver to maintain stability while accelerating.

Driving condition on road with different surface friction characteristics
X131011C01
1.406,1.948 1.979,1.823 1.979,1.823 1.406,1.688 true 5.396,1.26 6.49,0.656 true 4.958,3.292 4.958,2.229 true 1.177,3.208 1.448,3.479 0.271,0.271 10 false *A 3.167,3.167 3.469,3.396 0.302,0.229 10 false *B 4.875,3.302 5.083,3.521 0.208,0.219 10 false *1 0.771,0.333 1.073,0.615 0.302,0.281 10 false :*a 2.021,1.719 2.281,2.031 0.26,0.313 10 false *b 6.531,0.521 6.802,0.802 0.271,0.281 10 false *c
*A Without TRAC *B With TRAC
*1 Brake Actuator
·

Skid Control ECU


- -
*a Slippery Surface *b Excessive driving force causes the drive wheels to slip
*c Regulating the throttle to control the engine output - -




Outline of A-TRAC (4WD Models)


a.

General

i.

When the vehicle drive mode is 4H or 4L, the A-TRAC helps restrain wheelspin by controlling the brake fluid pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to LSD.

·

It independently controls the brake hydraulic pressure to the four wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.

With A-TRAC
X131012C01
5.167,0.469 5.823,0.25 true 4.74,1.719 5.406,1.229 5.406,1.229 4.771,1.229 true 2.573,1.688 1.677,1.688 1.677,1.688 2.552,1.219 true 1.677,2.448 2.156,2.25 true 3.542,0.917 3.823,1.115 0.281,0.198 10 false *1 3.25,1.719 3.469,1.948 0.219,0.229 10 false *2 3.427,2.042 3.677,2.271 0.25,0.229 10 false *3 3.417,2.563 3.646,2.75 0.229,0.188 10 false *4 4.667,2.313 4.927,2.521 0.26,0.208 10 false *a 4.698,0.042 4.917,0.25 0.219,0.208 10 false *b 1.49,1.573 1.698,1.823 0.208,0.25 10 false *c 1.479,2.354 1.688,2.615 0.208,0.26 10 false *d 2.469,0.125 2.729,0.333 0.26,0.208 10 false *a 2.406,2.438 2.625,2.646 0.219,0.208 10 false *b 5.448,1.115 5.75,1.417 0.302,0.302 10 false *c 5.844,0.125 6.073,0.396 0.229,0.271 10 false *d
*1 Engine *2 Actuator Portion
*3 Skid Control ECU *4 A.D.D. Detection Switch
*a Traction *b Braking
*c Driving Torque *d Snowy or Icy Surface


With A-TRAC
X131013C01
4.667,1.208 5.458,1.208 true 5.063,0.542 5.583,0.542 true 1.969,1.75 2.49,1.75 true 1.563,2.208 2.083,2.208 true 3.469,0.99 3.708,1.177 0.24,0.188 10 false *1 4.802,1.865 5.031,2.104 0.229,0.24 10 false *a 1.76,1.646 1.979,1.854 0.219,0.208 10 false *b 1.365,2.104 1.583,2.323 0.219,0.219 10 false *c 2.156,0.729 2.385,0.969 0.229,0.24 10 false *a 5.625,0.438 5.865,0.688 0.24,0.25 10 false *c 5.49,1.125 5.729,1.354 0.24,0.229 10 false *b
*1 Engine - -
*a No Traction *b Driving Torque
*c Snowy or Icy Surface - -





b.

Effectiveness of A-TRAC

i.

The effectiveness of A-TRAC is as follows:

·

Off-road drivability that is equivalent to having the center differential locked and limited slip differentials on both front and rear has been realized.

·

This function makes the operation of the differential lock switches basically unnecessary to ensure the ease of driving.

·

A-TRAC allows for drivability benefits similar to those of locked differentials, while still allowing for the vehicle to be steered at low speeds, without the binding that would normally be associated with locked differentials.





Outline of Auto LSD


a.

The auto LSD achieves the LSD effect by regulating the hydraulic pressure that acts on the drive wheels.

i.

TRAC enhances the start-off performance of the vehicle during low-grip surface conditions, such as snow or mud, by restricting the acceleration effort during a start-off, in order to help prevent the wheels from spinning.


ii.

Auto LSD tends to enhance the acceleration effort somewhat, in order to apply greater drive torque to the wheel that has grip. Thus, this function enables the vehicle to get unstuck if a wheel loses its grip, and enhances the vehicle's start-off performance when high-resistance surface conditions exist, such as loose gravel or sand.

With Auto LSD
X131014C01
4.594,1.448 5.125,0.917 5.125,0.917 4.594,0.917 true 5.021,2.063 5.677,2.063 true 2.542,1.063 2.792,1.313 0.25,0.25 10 false *1 3.24,1.531 3.5,1.729 0.26,0.198 10 false *2 3.396,1.833 3.667,2.052 0.271,0.219 10 false *3 4.042,2.479 4.271,2.708 0.229,0.229 10 false *4 4.5,0.031 4.729,0.24 0.229,0.208 10 false *a 4.479,2.292 4.74,2.51 0.26,0.219 10 false *b 5.719,1.958 5.979,2.208 0.26,0.25 10 false *c 5.167,0.813 5.427,1.052 0.26,0.24 10 false *d
*1 Engine *2 Actuator Portion
*3 Skid Control ECU *4 VSC OFF Switch
*a Traction *b Braking
*c Snowy or Icy Surface *d Driving Torque


Without Auto LSD
X131015C01
4.594,1.635 5.156,1.635 true 5,2.167 5.563,2.167 true 2.521,1.198 2.781,1.438 0.26,0.24 10 false *1 4.74,0.708 4.979,0.948 0.24,0.24 10 false *a 4.438,2.438 4.688,2.656 0.25,0.219 10 false *b 5.594,2.052 5.844,2.302 0.25,0.25 10 false *c 5.208,1.542 5.51,1.771 0.302,0.229 10 false *d
*1 Engine - -
*a No Torque Transferred *b Slipping
*c Snowy or Icy Surface *d Driving Torque





Outline of VSC


a.

General

i.

The following are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit.


ii.

The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle experiences one of the conditions indicated below.

·

When the front wheels lose grip in relation to the rear wheels (understeer - front wheel skid tendency).

·

When the rear wheels lose grip in relation to the front wheels (oversteer - rear wheel skid tendency).

X102948C03
2.167,2.281 2.479,2.479 0.313,0.198 10 false *a 4.75,2.25 5.063,2.448 0.313,0.198 10 false *b
*a Front Wheel Skid Tendency *b Rear Wheel Skid Tendency





b.

Method for Determining the Vehicle Condition

i.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and the vehicle's lateral acceleration, which are then used by the skid control ECU for calculations.


ii.

Determining a Front Wheel Skid

·

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate.

·

When the vehicle's actual yaw rate is smaller than the target yaw rate (a target yaw rate is determined based on the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel.

·

Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X105305C03
3.698,0.094 4.052,0.427 0.354,0.333 10 false *a 4.688,0.854 5.042,1.188 0.354,0.333 10 false *b
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate




iii.

Determining a Rear Wheel Skid

·

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X105306C03
3.563,0.083 4.052,0.479 0.49,0.396 10 false *a 3.99,0.115 4.479,0.51 0.49,0.396 10 false *b
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
V100136

Slip Angle - -





c.

VSC Operation Methods

i.

When the skid control ECU determines that the vehicle exhibits a tendency to front wheel skid or rear wheel skid, it decreases engine output and applies the brake to a front or rear wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method may differ depending on the vehicle's characteristics and driving conditions.


ii.

Dampening a Strong Front Wheel Skid

·

When the skid control ECU determines that there is a large front wheel skid tendency, it attempts to counteract the tendency based on the extent of that tendency. The skid control ECU controls the engine power output and applies the brakes of the rear inside wheel (the inside of the turn).

Front Wheel Skid Tendency (Making a Right Turn)
X131016

V100135

Brake Force
V100136

Control Moment



iii.

Dampening a Strong Rear Wheel Skid

·

When the skid control ECU determines that there is a large rear wheel skid tendency, it attempts to counteract the tendency based on the extent of that tendency. It applies the brakes of the front outer wheels (the outside of the turn), and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the rear brakes, as necessary.

Rear Wheel Skid Tendency (Making a Right Turn)
X105308

V100135

Brake Force
V100136

Control Moment





Outline of Trailer Sway Control


a.

If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by load, or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.

X125194E01
0.146,0.063 1.927,0.479 1.781,0.417 10 false Without Trailer Sway Control 0.448,1.271 1.146,1.646 0.698,0.375 10 false Side Wind 0.167,1.802 1.74,2.229 1.573,0.427 10 false With Trailer Sway Control 0.448,3 1.146,3.375 0.698,0.375 10 false Side Wind 3.479,2.969 5.865,3.365 2.385,0.396 10 false Brake Control + Engine Output Control

NOTICE:
·

Trailer sway control is a part of the VSC function. Accordingly, if the VSC OFF Mode or VSC is not functioning normally, trailer sway control will not operate.

·

Trailer sway control will be unable to stabilize the vehicle if a trailer is being towed which cannot be physically controlled due to the influence of the vehicle, road surface, driving conditions and so on.




b.

Trailer Sway Control Operation

i.

The skid control ECU detects the occurrence of trailer sway based on signals from the yaw rate and deceleration sensor and the steering angle sensor.


ii.

Trailer sway can be reduced by decelerating the vehicle. When the skid control ECU detects trailer sway, it controls the brakes of each wheel while simultaneously requesting engine output control from the ECM and reducing vehicle speed.


iii.

Moreover, by using brake control to reduce the yaw moment caused by trailer sway, trailer sway can be reduced more quickly than by simply decelerating the vehicle.


iv.

The slip indicator light on the combination meter flashes when trailer sway control is in operation. Also, the stop light illuminates to inform vehicles behind that the vehicle is decelerating.

X125195C02
2.052,0.948 2.302,1.156 0.25,0.208 10 false *a 3.646,1.125 3.958,1.281 0.313,0.156 10 false *b 5.063,1.865 5.375,2.021 0.313,0.156 10 false *c 5.365,1.26 5.677,1.417 0.313,0.156 10 false *d
*a Trailer Sway *b Deceleration Force Caused by Brake Control and Engine Output Control
*c Yaw Moment Caused by Trailer Sway *d Control Moment Caused by Brake Control


X112414E01
4.385,0.49 4.385,0.292 4.385,0.292 4.792,0.292 false 3.5,1.219 3.906,1.219 3.906,1.219 3.906,1.021 false 0.271,0.583 1.615,1.135 1.344,0.552 10 false Yaw Rate and Lateral Acceleration 0.271,1.531 1.615,2.083 1.344,0.552 10 false Trailer Sway Control 0.271,2.25 1.615,2.802 1.344,0.552 10 false Brake Force 0.271,3.021 1.615,3.573 1.344,0.552 10 false Yaw Moment 0.271,4.01 1.615,4.563 1.344,0.552 10 false Vehicle Speed 6.552,0.74 6.948,1.167 0.396,0.427 10 false Time 6.552,1.698 6.948,2.125 0.396,0.427 10 false Time 6.552,2.333 6.948,2.76 0.396,0.427 10 false Time 6.552,3.115 6.948,3.542 0.396,0.427 10 false Time 6.552,4.385 7.073,4.646 0.521,0.26 10 false Time 4.865,0.208 6.208,0.76 1.344,0.552 10 false Lateral Acceleration 2.865,1.135 3.625,1.5 0.76,0.365 10 false Yaw Rate 4.313,1.375 4.708,1.802 0.396,0.427 10 false On 5.802,1.813 6.198,2.24 0.396,0.427 10 false Off




Layout of Main Components


X131017C01
4.781,3.063 4.313,1.76 true 6.198,2.823 5.313,2.292 true 2.021,3.823 2.313,3.146 true 0.771,3.26 2.344,2.365 true 0.448,1.969 1.396,2.479 true 2.5,2.167 1.615,0.604 true 1.969,4.531 2.833,4.792 true 1.688,5.781 3.365,5.198 true 4.604,5.042 5.667,5.51 true 1.5,0.406 1.76,0.625 0.26,0.219 10 false *1 0.271,1.844 0.458,2.094 0.188,0.25 10 false *2 0.583,3.208 0.823,3.448 0.24,0.24 10 false *3 1.917,3.833 2.198,4.073 0.281,0.24 10 false *4 4.75,3.083 4.969,3.302 0.219,0.219 10 false *5 6.25,2.792 6.5,3.042 0.25,0.25 10 false *6 1.802,4.427 2.01,4.677 0.208,0.25 10 false *7 1.5,5.708 1.719,5.938 0.219,0.229 10 false *8 5.729,5.448 5.958,5.698 0.229,0.25 10 false *9
*1 Brake Booster
·

Booster Solenoid

·

Micro Switch

·

Booster Stroke Sensor


*2 Front Speed Sensor RH
*3 Brake Actuator
·

Skid Control ECU

·

Master Cylinder Pressure Sensor


*4 Front Speed Sensor LH
*5 Rear Speed Sensor RH *6 Rear Speed Sensor LH
*7 ECM *8 Throttle Body
·

Throttle Position Sensor


*9 Engine Room R/B
·

BRK NO. 1 Relay

·

BRK NO. 2 Relay


- -


X131018C01
2.521,1.438 2.521,0.583 true 1.115,0.979 2.25,1.656 true 0.667,3.26 2.688,2.219 true 0.875,4.688 1.344,4.219 true 3.646,4.49 3.646,3.76 true 5.333,1.885 6.479,1.146 true 2.438,0.354 2.656,0.573 0.219,0.219 10 false *1 0.938,0.844 1.156,1.083 0.219,0.24 10 false *2 0.479,3.188 0.698,3.469 0.219,0.281 10 false *3 0.74,4.688 0.958,4.906 0.219,0.219 10 false *4 2.885,3.76 3.135,3.99 0.25,0.229 10 false *5 3.573,4.5 3.813,4.74 0.24,0.24 10 false *6 6.51,1.021 6.771,1.271 0.26,0.25 10 false *7
*1 Combination Meter Assembly
·

ABS Warning Light

·

Brake System Warning Light

·

Slip Indicator Light

·

TRAC OFF Indicator Light

·

VSC OFF Indicator Light

·

Auto LSD Indicator Light


*2 Steering Angle Sensor
*3 DLC3 *4 Stop Light Switch
*5 VSC OFF Switch *6 Yaw Rate and Deceleration Sensor
*7 4WD Control ECU - -



Function of Main Components


Component Function

*: 4WD models

Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS, EBD or brake assist system.
Brake System Warning Light
·

Lights up together with the ABS warning light to alert the driver when the skid control ECU detects a malfunction in the EBD control or when a malfunction occurs in the brake booster.

·

Lights up to alert the driver when the brake fluid level is low.

·

Lights up to alert the driver when the parking brake is application.


Slip Indicator Light Blinks to inform the driver when the VSC or trailer sway control is operated.
TRAC OFF Indicator Light Lights up to inform the driver when the VSC OFF mode is entered using the VSC OFF switch.
VSC OFF Indicator Light
·

Lights up to inform the driver when the auto LSD mode or VSC OFF mode is entered using the VSC OFF switch.

·

When the 4WD control switch is 4L position the VSC OFF indicator light lights up to alert the driver.

·

When the skid control ECU detects a malfunction and determines that the TRAC, A-TRAC, auto LSD, VSC or trailer sway control is not available, the VSC OFF indicator light comes on to alert the driver (Only while in VSC OFF mode, this indicator light will blink if an abnormality is detected).


Auto LSD IndicatorLight
·

Lights up to inform the driver when the TRAC OFF mode is entered using the VSC OFF switch.

·

Lights up together with the VSC OFF indicator light to inform the driver when the auto LSD mode is entered using the VSC OFF switch.


Speed Sensors (4) Detects the wheel speed of each of the four wheels.
Yaw Rate and Deceleration Sensor
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's lateral acceleration (2WD models).

·

Detects the vehicle's longitudinal and lateral acceleration (4WD models).


Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Brake Actuator Actuator Portion Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS with EBD, brake assist, TRAC, A-TRAC, auto LSD, VSC and trailer sway control in order to control the fluid pressure that is applied to the brakes for the different wheels.
Master Cylinder Pressure Sensor Detects the master cylinder pressure.
Solenoid Relay Controls power supplied to the solenoid valves.
Motor Relay Supplies power to the pump motor in the brake actuator.
Skid Control ECU
·

Judges the vehicle driving conditions based on signals from each sensor, and sends brake control signals to the brake actuator.

·

Judges the vehicle driving conditions based on signals from each sensor, and calculates the amount of engine output adjustment required. The skid control ECU transmits command signals to the ECM.


Brake Booster Booster Solenoid When the VSC system is activated, this solenoid operates in accordance with the signals from the skid control ECU to boost the hydraulic pressure to the wheel cylinders.
Micro Switch Detects that the brake pedal is depressed.
Booster Stroke Sensor Detects the brake pedal stroke distance.
VSC OFF Switch
·

Cancels the TRAC or VSC system.

·

Selects the 4 modes (Normal mode, TRAC OFF mode, auto LSD mode, VSC OFF mode).


A.D.D. Detection Switch* Detects the drive mode (2WD or 4WD).
Parking Brake Switch Detects parking brake application.
Stop Light Switch Detects brake pedal application.
4WD Control ECU* Detects the transfer shift position (4H or 4L) and sends the information to the skid control ECU.
ECM
·

Sends the throttle valve angle signal, accelerator pedal position signal, engine speed signal, and intake air temperature signal to the skid control ECU.

·

Receives an engine output adjustment command signals from the skid control ECU. Based on these signals, the ECM operates the throttle valve to control engine output.




Brake Booster


a.

General

i.

When the VSC system is activated, the booster solenoid that is enclosed in the brake booster moves the air valve to regulate the amount of pressure applied by the master cylinder. As at this time the skid control ECU controls the solenoid in accordance with the signals from the master cylinder pressure sensor, thus supplementing the brake fluid pressure when the VSC system is activated, resulting in excellent brake control.


ii.

Because the brake pedal could move down with the activation of the VSC system, the fact that the driver is depressing the brake pedal is determined by the release switch that is enclosed in the brake booster.


iii.

The booster stroke sensor is used to detect a malfunction of the active brake booster. If the booster malfunctions, the brake assist system will be activated to assist the braking force.

System Diagram
X131020E01
5.104,2.802 6.729,3.229 1.625,0.427 10 false Booster Stroke Sensor 5.396,1.865 6.573,2.229 1.177,0.365 10 false Micro Switch 5.313,0.917 6.635,1.333 1.323,0.417 10 false Booster Solenoid 5.406,0.344 6.5,0.719 1.094,0.375 10 false Brake Booster 3.177,1.625 3.969,2.573 0.792,0.948 10 false Skid Control ECU 0.313,0.375 1.469,0.813 1.156,0.438 10 false Brake Actuator 0.479,1.708 2.594,2.104 2.115,0.396 10 false Master Cylinder Pressure Sensor



b.

Construction

i.

The active brake booster mainly consists of a push rod, air valve, booster solenoid, booster solenoid case, release switch, push ring, push plate and booster stroke sensor.

X131021C01
2.583,1.271 2.344,0.417 true 3.604,1.708 4.031,0.552 true 6.406,2.74 5.969,1.969 true 3.01,3.281 2.615,2.354 true 2.365,3.365 2.365,2.281 true 1.625,3.26 2.083,2.5 true 0.542,1.01 1.698,1.802 true 2.083,1.5 1.208,0.448 true 2.24,0.198 2.479,0.406 0.24,0.208 10 false *1 1.083,0.25 1.323,0.458 0.24,0.208 10 false *2 0.385,0.875 0.594,1.125 0.208,0.25 10 false *3 1.521,3.25 1.729,3.458 0.208,0.208 10 false *4 2.302,3.365 2.573,3.594 0.271,0.229 10 false *5 2.969,3.281 3.26,3.51 0.292,0.229 10 false *6 6.365,2.74 6.646,3.042 0.281,0.302 10 false *7 0.552,1.781 0.74,2 0.188,0.219 10 false *a 6.385,1.823 6.573,2.052 0.188,0.229 10 false *b 3.979,0.323 4.24,0.552 0.26,0.229 10 false *8
*1 Booster Stroke Sensor *2 Push Ring
*3 Push Plate *4 Release Switch
*5 Booster Solenoid *6 Booster Solenoid Case
*7 Push Rod *8 Air Valve
*a To Master Cylinder *b From Brake Pedal




c.

Operation

i.

Normal Braking

·

During normal braking, the input load from the brake pedal is transmitted to the push rod, air valve, booster solenoid case, push ring, push plate, and reaction disc, and is output to the master cylinder.

·

At this time, the air valve moves, and air flows into the variable pressure chamber. This creates a pressure difference between the constant pressure chamber and the variable pressure chamber, and the input load from the brake pedal is amplified and output to the master cylinder.

X131022C01
3.021,0.865 3.302,0.448 true 2.313,0.896 2.313,0.385 true 1.76,0.854 1.594,0.427 true 2.031,1.51 0.646,0.719 true 0.542,1.375 1.688,1.823 true 0.625,2.458 1.333,2.198 true 2.167,3.292 2.615,2.354 true 4.125,3.031 3.844,2.177 true 6.5,2.594 5.958,2 true 2.24,0.198 2.479,0.396 0.24,0.198 10 false *1 0.479,0.573 0.708,0.813 0.229,0.24 10 false *2 0.385,1.25 0.615,1.479 0.229,0.229 10 false *3 0.458,2.385 0.677,2.625 0.219,0.24 10 false *4 2.094,3.292 2.333,3.531 0.24,0.24 10 false *5 6.479,2.594 6.708,2.813 0.229,0.219 10 false *6 1.479,0.208 1.719,0.448 0.24,0.24 10 false *a 0.604,1.802 0.813,2.042 0.208,0.24 10 false *b 4.094,3.031 4.354,3.271 0.26,0.24 10 false *c 6.396,1.802 6.677,2.052 0.281,0.25 10 false *d 3.25,0.229 3.49,0.469 0.24,0.24 10 false *a
*1 Constant Pressure Chamber *2 Push Ring
*3 Push Plate *4 Release Switch
*5 Booster Solenoid Case *6 Push Rod
*a Variable Pressure Chamber *b To Master Cylinder
*c Air Valve "Open" *d From Brake Pedal




ii.

VSC System Operation

·

When the VSC system is activated, current flows to the booster solenoid in accordance with the signals from the skid control ECU. The booster solenoid core and the control valve then move toward the brake pedal, thus moving the valve seat toward the brake pedal.

·

As a result, the air valve opens and air flows into the variable pressure chamber. This creates a pressure difference between the constant pressure chamber and the variable pressure chamber. The pressure difference causes the brake booster to activate and output to the master cylinder.

·

VSC operation may cause the brake pedal to move downward. A stop light inhibit relay is provided to prevent undesired operation of the stop lights due to operation of VSC.

X131023C01
3.938,1.542 4.615,0.583 true 3.552,1.583 3.906,0.552 true 2.99,0.865 3.156,0.354 true 2.302,0.958 2.302,0.323 true 1.719,0.865 1.5,0.323 true 1.854,3.135 2.125,2.052 true 2.375,3.188 2.375,2.26 true 6.469,2.552 6.083,1.979 true 4.104,2.99 3.865,2.177 true 2.219,0.104 2.469,0.302 0.25,0.198 10 false *1 1.76,3.146 2.031,3.385 0.271,0.24 10 false *2 2.302,3.198 2.552,3.469 0.25,0.271 10 false *3 6.417,2.563 6.677,2.833 0.26,0.271 10 false *4 4.594,0.417 4.844,0.656 0.25,0.24 10 false *5 3.865,0.354 4.094,0.583 0.229,0.229 10 false *6 3.125,0.146 3.344,0.375 0.219,0.229 10 false *a 0.594,1.802 0.823,2.052 0.229,0.25 10 false *b 4.052,2.979 4.302,3.25 0.25,0.271 10 false *c 1.396,0.125 1.646,0.323 0.25,0.198 10 false *a
*1 Constant Pressure Chamber *2 Booster Solenoid Core
*3 Booster Solenoid *4 Push Rod
*5 Valve Seat *6 Control Valve
*a Variable Pressure Chamber *b To Master Cylinder
*c Air Valve "Open" - -






Speed Sensor


a.

General

i.

Active type speed sensors can detect the wheel rotation. This sensor contains a sensor IC, which consists of the Magnetic Resistance Elements (MREs).


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.

X131024C01
1.167,0.958 0.948,0.365 true 1.677,3.344 1.427,2.833 true 5.417,1.073 5.177,0.417 true 6.25,1.688 6.573,1.01 true 5.208,2.979 5.625,1.844 true 4.125,2.104 4.51,1.781 4.51,1.781 3.948,1.948 true 3.073,2.063 2.698,1.729 2.698,1.729 3.25,1.896 true 0.844,0.167 1.083,0.396 0.24,0.229 10 false *1 1.635,3.354 1.917,3.573 0.281,0.219 10 false *2 5.104,2.979 5.344,3.198 0.24,0.219 10 false *3 6.542,0.802 6.792,1.031 0.25,0.229 10 false *4 2.51,1.604 2.74,1.823 0.229,0.219 10 false *a 4.542,1.677 4.792,1.917 0.25,0.24 10 false *b 5.063,0.208 5.313,0.427 0.25,0.219 10 false *1
*1 Speed Sensor *2 Sensor IC
·

MREs


*3 Sensor Rotor *4 Axle Hub
*a S Poles *b N Poles




b.

Detection Method

i.

An active type speed sensor uses a sensor IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses (vehicle speed signal).

X131025E01
6.542,1.729 7.01,2.031 0.469,0.302 10 false Time 3.833,0.885 4.333,1.823 0.5,0.938 10 false Output Current 2.75,0.958 3.198,1.552 0.448,0.594 10 false Sensor IC 1.948,0.948 2.458,1.229 0.51,0.281 10 false MRE A 1.938,1.26 2.469,1.552 0.531,0.292 10 false MRE B 0.385,1.865 1.781,2.615 1.396,0.75 10 false Sensor Rotor (Bearing Inner Race)

Detection Speed From 0.5 km/h
Direction Detection Wheel rotation direction is not judged.


ii.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X131026E01
4.854,1.458 4.854,0.823 4.854,0.823 5.25,0.823 true 4.458,2.146 4.458,1.781 4.458,1.781 4.688,1.781 true 5.021,2.958 6.094,3.323 1.073,0.365 10 false Passive Type 5.313,0.729 6.323,1.052 1.01,0.323 10 false No Detecction 4.74,1.688 5.74,2.01 1,0.323 10 false No Detecction 6.135,2.708 7.083,3.083 0.948,0.375 10 false Analog Output 3.677,2.073 4.198,2.875 0.521,0.802 10 false Sensor Output 3.677,1.313 4.198,2.156 0.521,0.844 10 false Vehicle Speed 2.771,2.01 3.271,2.76 0.5,0.75 10 false Digital Output 1.354,2.938 2.427,3.302 1.073,0.365 10 false Active Type 0.115,1.135 0.615,1.979 0.5,0.844 10 false Vehicle Speed 0.104,2.427 0.604,3.26 0.5,0.833 10 false Sensor Output




VSC OFF Switch


a.

When the driving mode is 2WD mode, the VSC OFF switch can select the 4 modes (Normal mode, TRAC-OFF mode, auto LSD mode, VSC OFF mode).


b.

When the driving mode is 4WD mode, the VSC OFF switch can select the 2 modes (normal mode, VSC OFF mode).


c.

The switch mode transition for 2WD mode is as follows:

i.

Briefly pressing the VSC OFF switch in normal mode enters TRAC OFF mode, turning the auto LSD on [(1) in illustration].


ii.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped enters auto LSD mode, disabling each function except for auto LSD [(2) in illustration].


iii.

At the auto LSD mode, pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped enters VSC OFF mode, disabling TRAC, auto LSD and VSC functions [(3) in illustration].


iv.

At the VSC OFF mode, pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped returns to auto LSD mode, disabling each function except for auto LSD [(4) in illustration].


v.

Briefly pressing the VSC OFF switch in TRAC OFF, auto LSD mode, or VSC OFF mode or turning the ignition switch off returns to normal mode [(5) in illustration].

Switch Control
X131027E01
3.083,0.5 4.313,0.844 1.229,0.344 10 false Normal Mode 1.354,1.698 2.594,2.01 1.24,0.313 10 false TRAC OFF Mode 4.438,1.708 5.698,2.042 1.26,0.333 10 false AUTO LSD Mode 4.448,2.969 5.688,3.292 1.24,0.323 10 false VSC OFF Mode 0.865,2.552 2.135,2.896 1.271,0.344 10 false : Briefly pressing 0.823,2.979 2.104,3.323 1.281,0.344 10 false : Briefly pressing 0.823,3.375 3.927,3.708 3.104,0.333 10 false : Pressing and holding for 3 seconds or more 4.396,1.115 4.656,1.365 0.26,0.25 10 false (2) 1.385,1.125 1.635,1.385 0.25,0.26 10 false (1) 4.406,2.333 4.688,2.604 0.281,0.271 10 false (3) 5.354,2.344 5.635,2.635 0.281,0.292 10 false (4) 5.344,1.135 5.625,1.417 0.281,0.281 10 false (5) 2.323,1.146 2.615,1.427 0.292,0.281 10 false (5) 6.24,1.698 6.563,1.958 0.323,0.26 10 false (5) 3.313,1.927 3.573,2.177 0.26,0.25 10 false (2)



d.

The switch mode transition for 4WD mode is as follows:

i.

At the normal mode, pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped enters VSC OFF mode, disabling TRAC and VSC functions [(1) in illustration].


ii.

Briefly pressing the VSC OFF switch in VSC OFF mode or turning the ignition switch off returns to normal mode [(2) in illustration].

Switch Control
X131028E01
1.583,0.552 2.635,0.896 1.052,0.344 10 false Normal Mode 1.479,1.844 2.615,2.229 1.135,0.385 10 false VSC OFF Mode 4.167,1.365 5.531,1.688 1.365,0.323 10 false : Briefly pressing 4.156,1.833 7.073,2.219 2.917,0.385 10 false : Pressing and holding for 3 seconds or more 2.385,1.302 2.667,1.583 0.281,0.281 10 false (2) 1.438,1.292 1.698,1.563 0.26,0.271 10 false (1)



e.

The operation of the brake control functions and the illumination state of the respective indicator lights in each mode are as follows:

2WD Models
Item Brake Control Function Indicator Light
TRAC TRAC Auto LSD VSC TRAC OFF Indicator Light Auto LSD Indicator Light VSC OFF Indicator Light
Normal Mode ○ - ○ Off Off Off
TRAC OFF Mode - ○ ○ Off On Off
Auto LSD Mode - ○ - Off On On
VSC OFF Mode - - - On Off On

4WD Models
Item Brake Control Function Indicator Light
TRAC A-TRAC Auto LSD VSC TRAC OFF Indicator Light Auto LSD Indicator Light VSC OFF Indicator Light
2WD Normal Mode ○ - - ○ Off Off Off
TRAC OFF Mode - - ○ ○ Off On Off
Auto LSD Mode - - ○ - Off On On
VSC OFF Mode - - - - On Off On
4WD (4H) Normal Mode - ○ - ○ Off Off Off
TRAC OFF Mode - - - ○ On Off Off
VSC OFF Mode - - - - On Off On
4WD (4L) Normal Mode - ○ - - Off Off On
VSC OFF Mode - - - - On Off On



Brake Actuator


a.

The brake actuator consists of the actuator portion, skid control ECU, solenoid relay, motor relay, pump motor, and master cylinder pressure sensor.

i.

The actuator portion consists of 12 solenoid valves, pump motor, 2 pumps, 2 reservoirs, and master cylinder pressure sensor.


ii.

The 12 solenoid valves consist of 2 master cylinder cut solenoid valves [(1), (4)], 2 reservoir cut solenoid valves [(2), (3)], 4 pressure holding solenoid valves [(5), (6), (7), (8)], and 4 pressure reduction solenoid valves [(9), (10), (11), (12)].

Hydraulic Circuit
X131033C01
3.198,6.531 3.573,7.021 3.573,7.021 3.979,6.531 true 3.198,5.125 3.583,5.969 3.583,5.969 3.979,5.125 true 2.99,0.885 3.219,1.167 0.229,0.281 10 false *1 0.75,1.469 1.01,1.656 0.26,0.188 10 false *2 5.156,1.865 5.438,2.104 0.281,0.24 10 false *3 3.521,5.99 3.823,6.208 0.302,0.219 10 false *4 3.51,7.052 3.771,7.313 0.26,0.26 10 false *5 1.385,3.563 1.688,3.833 0.302,0.271 10 false (1) 1.396,7.417 1.635,7.625 0.24,0.208 10 false *a 2.333,7.417 2.563,7.667 0.229,0.25 10 false *b 4.708,7.417 4.958,7.635 0.25,0.219 10 false *c 5.656,7.427 5.875,7.635 0.219,0.208 10 false *d 2.76,3.552 3.063,3.823 0.302,0.271 10 false (2) 4.281,3.563 4.583,3.833 0.302,0.271 10 false (3) 5.625,3.552 5.927,3.823 0.302,0.271 10 false (4) 1.396,4.875 1.698,5.146 0.302,0.271 10 false (5) 2.323,4.875 2.583,5.104 0.26,0.229 10 false (6) 4.729,4.875 5.042,5.104 0.313,0.229 10 false (7) 5.667,4.885 5.938,5.104 0.271,0.219 10 false (8) 5.625,5.958 5.99,6.24 0.365,0.281 10 false (12) 4.688,5.948 5.021,6.156 0.333,0.208 10 false (11) 2.354,5.948 2.708,6.167 0.354,0.219 10 false (10) 1.406,5.958 1.667,6.24 0.26,0.281 10 false (9)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Pumps
*5 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right





System Operation


a.

Normal Braking

i.

During normal braking, all solenoid valves are turned off.

X131034C01
3.219,5.073 3.583,5.813 3.583,5.813 3.948,5.094 true 3.229,6.542 3.615,7.115 3.615,7.115 3.958,6.542 true 3.031,0.885 3.25,1.125 0.219,0.24 10 false *1 0.75,1.469 1.01,1.677 0.26,0.208 10 false *2 5.125,1.896 5.417,2.073 0.292,0.177 10 false *3 1.406,3.552 1.656,3.781 0.25,0.229 10 false *4 2.75,3.552 2.99,3.75 0.24,0.198 10 false *5 4.26,3.542 4.51,3.771 0.25,0.229 10 false *6 5.635,3.552 5.906,3.813 0.271,0.26 10 false *7 1.406,4.875 1.635,5.083 0.229,0.208 10 false *8 2.333,4.875 2.583,5.094 0.25,0.219 10 false *9 4.677,4.875 5.031,5.063 0.354,0.188 10 false *10 5.667,4.875 6.021,5.083 0.354,0.208 10 false *11 1.365,5.948 1.677,6.156 0.313,0.208 10 false *12 2.302,5.938 2.635,6.125 0.333,0.188 10 false *13 4.698,5.948 5.042,6.156 0.344,0.208 10 false *14 5.646,5.948 6,6.177 0.354,0.229 10 false *15 3.469,5.844 3.792,6.094 0.323,0.25 10 false *16 3.5,7.135 3.844,7.406 0.344,0.271 10 false *17 1.385,7.396 1.625,7.656 0.24,0.26 10 false *a 2.333,7.417 2.594,7.646 0.26,0.229 10 false *b 4.708,7.406 4.948,7.656 0.24,0.25 10 false *c 5.635,7.406 5.906,7.677 0.271,0.271 10 false *d
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Reservoir Cut Solenoid Valve
*7 Master Cylinder Cut Solenoid Valve *8 Pressure Holding Solenoid Valve
*9 Pressure Holding Solenoid Valve *10 Pressure Holding Solenoid Valve
*11 Pressure Holding Solenoid Valve *12 Pressure Reduction Solenoid Valve
*13 Pressure Reduction Solenoid Valve *14 Pressure Reduction Solenoid Valve
*15 Pressure Reduction Solenoid Valve *16 Pumps
*17 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right




b.

ABS with EBD Operation

i.

Based on the signals received from the 4 wheel speed sensors and yaw rate and deceleration sensor, the skid control ECU calculates the wheel rotation speed and deceleration for each wheel, in order to check for a wheel slippage condition. According to the slippage condition, the ECU controls the pressure holding solenoid valves and pressure reduction solenoid valves in order to adjust the fluid pressure of the brakes for each of the wheels in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.

X102082C05
2.792,0.667 3.594,0.958 true 2.927,2.792 3.594,2.521 true 1.229,1.635 1.448,1.875 0.219,0.24 10 false *1 1.24,3.198 1.49,3.448 0.25,0.25 10 false *2 2.604,0.542 2.823,0.823 0.219,0.281 10 false *3 2.729,2.698 2.938,2.938 0.208,0.24 10 false *4 1.219,0.167 1.49,0.385 0.271,0.219 10 false *a 3.563,0.156 3.844,0.375 0.281,0.219 10 false *b 5.802,0.208 6.042,0.427 0.24,0.219 10 false *c 1.781,3.365 2.052,3.615 0.271,0.25 10 false *d 5.063,1.99 5.302,2.208 0.24,0.219 10 false *e 6.354,3.365 6.563,3.604 0.208,0.24 10 false *f
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*3 Port A *4 Port B
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d To Wheel Cylinder
*e To Reservoir and Pump *f From Wheel Cylinder


Brake Actuator Operation in ABS and EBD
Pressure Mode Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Pressure Holding Solenoid Valve (Port A) Off (Open) On (Closed) On (Closed)
Pressure Reduction Solenoid Valve (Port B) Off (Closed) Off (Closed) On (Open)
Wheel Cylinder Pressure Increase Hold Reduce



c.

Brake Assist Operation

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder, which is based on the master cylinder pressure sensor signals. If the ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the brakes to apply a greater fluid pressure than is present in the master cylinder.


ii.

Also, in the following cases, the system provides brake assist.

·

When greater braking force is needed than normal, the skid control ECU judges the need for brake assist using the master cylinder pressure sensor.

·

In the event of a brake booster failure, the skid control ECU judges the failure using the booster stroke sensor in the brake booster and master cylinder pressure sensor signals.

X131035C01
0.583,2.615 1.469,3.021 true 2.354,2.708 2.833,3.031 true 4.344,3.021 4.677,2.688 true 5.708,3.021 6.521,2.604 true 5.708,4.344 6.604,4.063 true 4.781,4.344 5.167,4.823 true 1.958,4.844 2.396,4.344 true 0.531,3.979 1.458,4.354 true 0.552,5.063 1.469,5.417 true 5.219,6.375 4.781,5.417 true 5.708,5.427 6.615,5.208 true 1.927,6.375 2.396,5.406 true 3.26,6.51 3.583,6.917 3.583,6.917 3.969,6.5 true 3.219,5.125 3.563,5.938 3.563,5.938 3.927,5.115 true 3,0.885 3.24,1.156 0.24,0.271 10 false *1 0.771,1.458 1,1.677 0.229,0.219 10 false *2 5.135,1.885 5.365,2.125 0.229,0.24 10 false *3 1.396,3.552 1.635,3.792 0.24,0.24 10 false *4 2.813,3.542 3.094,3.729 0.281,0.188 10 false *5 2.344,4.875 2.604,5.073 0.26,0.198 10 false *6 1.417,5.958 1.635,6.188 0.219,0.229 10 false *7 3.49,5.958 3.75,6.188 0.26,0.229 10 false *8 3.531,6.969 3.729,7.219 0.198,0.25 10 false *9 1.385,7.417 1.688,7.635 0.302,0.219 10 false *a 2.333,7.438 2.583,7.635 0.25,0.198 10 false *b 4.729,7.427 4.969,7.656 0.24,0.229 10 false *c 5.635,7.427 5.875,7.698 0.24,0.271 10 false *d 5.677,3.552 5.917,3.792 0.24,0.24 10 false *4 4.292,3.552 4.573,3.74 0.281,0.188 10 false *5 1.385,4.875 1.646,5.073 0.26,0.198 10 false *6 4.708,4.885 4.969,5.083 0.26,0.198 10 false *6 5.656,4.885 5.917,5.083 0.26,0.198 10 false *6 2.365,5.948 2.604,6.167 0.24,0.219 10 false *7 4.729,5.938 4.969,6.156 0.24,0.219 10 false *7 5.677,5.958 5.917,6.177 0.24,0.219 10 false *7 0.354,2.458 0.615,2.719 0.26,0.26 10 false (A) 2.135,2.573 2.396,2.854 0.26,0.281 10 false (B) 4.708,2.563 5.01,2.802 0.302,0.24 10 false (C) 6.563,2.479 6.865,2.781 0.302,0.302 10 false (D) 6.646,3.938 6.948,4.24 0.302,0.302 10 false (H) 5.177,4.802 5.458,5.042 0.281,0.24 10 false (G) 6.656,5.094 6.927,5.396 0.271,0.302 10 false (L) 5.146,6.365 5.417,6.615 0.271,0.25 10 false (K) 1.865,6.375 2.167,6.677 0.302,0.302 10 false (J) 0.396,4.917 0.625,5.167 0.229,0.25 10 false (I) 0.313,3.833 0.583,4.094 0.271,0.26 10 false (E) 1.865,4.844 2.156,5.083 0.292,0.24 10 false (F)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right



Brake Actuator Operation in Brake Assist
Item Brake Assist Not Activated Brake Assist Activated
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) On (Closed)
Port (D) Off (Open) On (Closed)
Reservoir Cut Solenoid Valve Port (B) Off (Closed) On (Open)
Port (C) Off (Closed) On (Open)
Pressure Holding Solenoid Valve Port (E) Off (Open) ←
Port (F) Off (Open) ←
Port (G) Off (Open) ←
Port (H) Off (Open) ←
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ←
Port (J) Off (Closed) ←
Port (K) Off (Closed) ←
Port (L) Off (Closed) ←



d.

TRAC Operation

i.

The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to achieve the required pressure. Thus, the brakes for the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes, to control slippage of the drive wheels.


ii.

The TRAC operation diagram shows the hydraulic circuit in the pressure increase mode when the TRAC is activated.


iii.

The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.

X131036C01
0.552,2.625 1.458,3 true 2.365,2.708 2.833,3.01 true 5.708,3.01 6.51,2.646 true 5.708,4.344 6.594,4.083 true 4.771,4.354 5.177,4.813 true 1.979,4.844 2.396,4.354 true 0.573,4.052 1.458,4.333 true 0.51,5.167 1.458,5.427 true 1.906,6.344 2.396,5.427 true 3.271,5.083 3.573,5.854 3.573,5.854 3.896,5.104 true 5.708,5.427 6.646,5.156 true 3.26,6.531 3.594,7.198 3.594,7.198 3.906,6.521 true 5.26,6.458 4.771,5.417 true 4.333,3.01 4.813,2.75 true 3.021,0.885 3.281,1.135 0.26,0.25 10 false *1 0.76,1.469 0.99,1.667 0.229,0.198 10 false *2 5.156,1.875 5.375,2.094 0.219,0.219 10 false *3 1.406,3.594 1.698,3.833 0.292,0.24 10 false *4 2.75,3.583 3,3.781 0.25,0.198 10 false *5 1.365,4.885 1.677,5.042 0.313,0.156 10 false *6 1.385,5.958 1.646,6.167 0.26,0.208 10 false *7 3.5,5.865 3.729,6.135 0.229,0.271 10 false *8 3.521,7.208 3.75,7.479 0.229,0.271 10 false *9 1.375,7.396 1.604,7.625 0.229,0.229 10 false *a 2.333,7.427 2.563,7.635 0.229,0.208 10 false *b 4.698,7.417 4.885,7.646 0.188,0.229 10 false *c 5.646,7.438 5.906,7.646 0.26,0.208 10 false *d 5.635,3.615 5.927,3.854 0.292,0.24 10 false *4 4.313,3.573 4.563,3.771 0.25,0.198 10 false *5 2.323,4.885 2.635,5.042 0.313,0.156 10 false *6 4.656,4.885 4.875,5.063 0.219,0.177 10 false *6 5.677,4.885 5.917,5.094 0.24,0.208 10 false *6 2.344,5.958 2.573,6.167 0.229,0.208 10 false *7 4.698,5.958 4.938,6.135 0.24,0.177 10 false *7 5.625,5.958 5.844,6.177 0.219,0.219 10 false *7 6.552,2.531 6.802,2.844 0.25,0.313 10 false (D) 4.865,2.604 5.125,2.885 0.26,0.281 10 false (C) 2.146,2.573 2.396,2.813 0.25,0.24 10 false (B) 0.333,2.49 0.573,2.76 0.24,0.271 10 false (A) 0.354,3.906 0.635,4.146 0.281,0.24 10 false (E) 1.865,4.854 2.146,5.094 0.281,0.24 10 false (F) 5.135,4.823 5.417,5.063 0.281,0.24 10 false (G) 6.635,3.958 6.917,4.25 0.281,0.292 10 false (H) 6.688,5.052 6.958,5.313 0.271,0.26 10 false (L) 5.208,6.469 5.49,6.708 0.281,0.24 10 false (K) 1.802,6.354 2.104,6.604 0.302,0.25 10 false (J) 0.365,5.031 0.583,5.302 0.219,0.271 10 false (I)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right


Brake Actuator Operation in TRAC
Item TRAC Activated
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) On (Closed) ← Off (Open)
Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve Port (B) Off (Closed) On (Open) ← Off (Closed)
Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve Port (G) Off (Open) On (Closed) ← ←
Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (K) Off (Closed) ← ← ←
Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve Port (E) Off (Open) ← On (Closed) Off (Open)
Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ← ← ←
Port (J) Off (Closed) ← ← ←



e.

A-TRAC Operation

i.

Based on the vehicle speed that has been calculated from the wheel speed sensors, and the signals of the yaw rate and deceleration sensor, the skid control ECU computes the target control speed.


ii.

The skid control ECU compares the target control speed and the speeds of the wheels to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valves of the brake actuator to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.


iii.

The A-TRAC operation diagram shows the hydraulic circuit in the pressure increase mode when the A-TRAC is activated.


iv.

As shown in the table below, the target control speed and the brake fluid pressure control.

Road Condition Transfer Range Control Outline
Ordinary 4H Target Control Speed Vehicle Speed + Slip Rate (4H range set value) Control designed to ensure the ease of driving on low-friction roads, dirt roads, and general roads.
Brake Control Gradual fluid Pressure Control
Rocky or Offroad 4L Target Control Speed Vehicle Speed + Slip Rate (4L range set value) Control designed for rugged offroad driving conditions.
Brake Control Sudden fluid Pressure Control


v.

A-TRAC Operation Precaution

·

When the A-TRAC is operating continuously while the vehicle is being driven on a slippery surface, the temperature of the brake pads increases. After a set length of time elapses, the skid control ECU alerts the driver of this condition by causing the multi buzzer to sound, and the slip indicator warning light to illuminate. Also, the A-TRAC operation is temporarily interrupted to protect the pads.

·

When the temperature of the pads decreases, the slip indicator light turns off, and the A-TRAC is automatically restored to an operating state.

A-TRAC Operation (When wheelspin of the front left wheel and rear right wheel occurs)
X131037C01
3.219,5.094 3.583,5.906 3.583,5.906 3.969,5.104 true 0.5,2.563 1.469,2.99 true 2.396,2.729 2.833,2.99 true 4.344,3 4.771,2.719 true 5.708,3.021 6.625,2.688 true 5.708,4.344 6.646,4.021 true 4.771,4.333 5.198,4.844 true 4.781,5.417 5.26,6.365 true 5.719,5.417 6.635,5.104 true 1.969,4.833 2.396,4.313 true 0.552,4.052 1.458,4.323 true 0.51,5.177 1.469,5.406 true 1.938,6.323 2.396,5.417 true 3.229,6.521 3.604,6.99 3.604,6.99 3.979,6.531 true 3.031,0.885 3.271,1.135 0.24,0.25 10 false *1 0.729,1.479 0.938,1.708 0.208,0.229 10 false *2 5.156,1.896 5.396,2.135 0.24,0.24 10 false *3 1.406,3.563 1.667,3.792 0.26,0.229 10 false *4 2.76,3.542 3.01,3.74 0.25,0.198 10 false *5 1.406,4.865 1.667,5.094 0.26,0.229 10 false *6 1.396,5.958 1.604,6.219 0.208,0.26 10 false *7 3.51,5.896 3.719,6.146 0.208,0.25 10 false *8 3.521,7.01 3.75,7.25 0.229,0.24 10 false *9 1.385,7.385 1.625,7.615 0.24,0.229 10 false *a 2.333,7.406 2.552,7.646 0.219,0.24 10 false *b 4.719,7.396 4.927,7.625 0.208,0.229 10 false *c 5.635,7.396 5.875,7.625 0.24,0.229 10 false *d 5.625,3.552 5.885,3.781 0.26,0.229 10 false *4 4.26,3.542 4.51,3.74 0.25,0.198 10 false *5 2.354,4.865 2.615,5.094 0.26,0.229 10 false *6 4.698,4.875 4.958,5.104 0.26,0.229 10 false *6 5.656,4.885 5.917,5.115 0.26,0.229 10 false *6 2.365,5.948 2.583,6.188 0.219,0.24 10 false *7 4.698,5.948 4.948,6.167 0.25,0.219 10 false *7 5.656,5.958 5.865,6.188 0.208,0.229 10 false *7 0.271,2.417 0.542,2.74 0.271,0.323 10 false (A) 2.177,2.563 2.406,2.833 0.229,0.271 10 false (B) 4.802,2.583 5.063,2.865 0.26,0.281 10 false (C) 6.667,2.563 6.938,2.781 0.271,0.219 10 false (D) 6.688,3.896 6.948,4.177 0.26,0.281 10 false (H) 5.125,4.844 5.385,5.063 0.26,0.219 10 false (G) 1.865,4.833 2.125,5.094 0.26,0.26 10 false (F) 0.323,3.906 0.583,4.177 0.26,0.271 10 false (E) 0.354,5.01 0.583,5.26 0.229,0.25 10 false (I) 1.854,6.323 2.115,6.604 0.26,0.281 10 false (J) 5.198,6.365 5.458,6.625 0.26,0.26 10 false (K) 6.677,4.979 6.938,5.24 0.26,0.26 10 false (L)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right


Brake Actuator Operation in A-TRAC (When wheelspin of the front left wheel and rear right wheel occurs)
Item A-TRAC Activated
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) On (Closed) ← Off (Open)
Port (D) Off (Open) On (Closed) ← Off (Open)
Reservoir Cut Solenoid Valve Port (B) Off (Closed) On (Open) ← Off (Closed)
Port (C) Off (Closed) On (Open) ← Off (Closed)
Front Brake Pressure Holding Solenoid Valve Port (G) Off (Open) ← On (Closed) Off (Open)
Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (K) Off (Closed) ← ← ←
Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve Port (E) Off (Open) On (Closed) ← ←
Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ← ← ←
Port (J) Off (Closed) ← ← ←




f.

Auto LSD Operation

i.

Auto LSD is a function that has effects similar to a mechanical type LSD. Auto LSD employs TRAC to control brake hydraulic pressure.


ii.

The skid control ECU detects slippage that occurs as a result of a rotational speed difference between the wheel with grip and the wheel without grip. Via the TRAC, the auto LSD detects the wheel slip that occurs (the wheel that is rotating faster), based on the rotational difference of the right and left drive wheels, and creates the auto LSD effect.


iii.

The operation of the brake actuator while auto LSD is working is the same as that of TRAC.


iv.

The auto LSD operation diagram shows the hydraulic circuit in the pressure increase mode when the auto LSD is activated.


v.

AUTO LSD Operation Condition

·

The following conditions must be met to enable operation of AUTO LSD. The AUTO LSD indicator light turns on when the operation is enabled.

Operating Condition Content
Select the 2WD mode Auto LSD is operational only in the 2WD mode.
Auto LSD Mode Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped enters auto LSD mode.
Accelerator Pedal On Auto LSD does not operate when the brake pedal is being operated. This ensures that auto LSD does not interfere with the driver's attempt to reducevehicle speed.
Vehicle Speed Driving at a speed under 50km/h (31mph).



vi.

Auto LSD Operation Precautions

·

Operate the auto LSD control only when the wheels are susceptible to spinning, such as when driving on a grooved, slippery, or rough surface.

·

Make sure the vehicle is stopped before turning on the auto LSD.

·

To prevent instability, do not continue driving the vehicle with the auto LSD turned on.

·

The slip indicator light will blink when the auto LSD is operating.

·

If the brake control of the auto LSD is operated continuously, the temperature of the brake pads will rise.

·

The skid control ECU, which monitors* the temperature of the brake pads, alerts the driver by sounding the multi buzzer if the brake pads becomes overheated. In this case, the auto LSD will temporarily stop operating in order to protect the system.

HINT:

*: The skid control ECU calculates the temperature of the brake pads based on its operating time.


·

The auto LSD applies the brakes to the drive wheel with the higher speed and controls the extent of the brake application in order to achieve the function of an LSD. However, it might not be able to achieve this function on a steep incline or on an extremely slippery surface, such as a frozen or snowy surface.

Auto LSD Operation (When wheelspin of the rear right wheel occurs)
X131038C01
0.51,2.635 1.469,3 true 2.333,2.729 2.844,3.01 true 4.792,2.708 4.333,3 true 5.708,3.021 6.573,2.646 true 5.708,4.344 6.625,4.031 true 5.188,4.875 4.771,4.323 true 2.01,4.833 2.396,4.323 true 0.51,4.052 1.458,4.333 true 0.427,5.156 1.458,5.417 true 1.844,6.354 2.396,5.417 true 5.219,6.344 4.781,5.406 true 6.656,5.104 5.708,5.406 true 3.229,5.115 3.583,5.958 3.583,5.958 3.948,5.115 true 3.229,6.5 3.615,7.063 3.615,7.063 3.948,6.5 true 3.01,0.885 3.229,1.115 0.219,0.229 10 false *1 0.74,1.469 0.969,1.667 0.229,0.198 10 false *2 5.167,1.875 5.385,2.115 0.219,0.24 10 false *3 1.406,3.542 1.656,3.781 0.25,0.24 10 false *4 2.771,3.531 3.031,3.729 0.26,0.198 10 false *5 1.396,4.865 1.646,5.094 0.25,0.229 10 false *6 1.406,5.948 1.604,6.208 0.198,0.26 10 false *7 3.51,5.979 3.729,6.229 0.219,0.25 10 false *8 3.542,7.073 3.76,7.313 0.219,0.24 10 false *9 1.396,7.396 1.615,7.646 0.219,0.25 10 false *a 2.323,7.406 2.5,7.646 0.177,0.24 10 false *b 4.719,7.406 4.99,7.615 0.271,0.208 10 false *c 5.656,7.406 5.906,7.656 0.25,0.25 10 false *d 5.656,3.552 5.906,3.792 0.25,0.24 10 false *4 4.271,3.542 4.531,3.74 0.26,0.198 10 false *5 2.354,4.875 2.604,5.104 0.25,0.229 10 false *6 4.719,4.865 4.969,5.094 0.25,0.229 10 false *6 5.688,4.865 5.938,5.094 0.25,0.229 10 false *6 2.344,5.948 2.542,6.208 0.198,0.26 10 false *7 4.729,5.948 4.927,6.208 0.198,0.26 10 false *7 5.635,5.948 5.833,6.208 0.198,0.26 10 false *7 0.302,2.49 0.542,2.781 0.24,0.292 10 false (A) 2.115,2.573 2.354,2.854 0.24,0.281 10 false (B) 4.823,2.573 5.094,2.875 0.271,0.302 10 false (C) 6.615,2.521 6.896,2.823 0.281,0.302 10 false (D) 6.667,3.906 6.938,4.188 0.271,0.281 10 false (H) 6.688,4.979 6.938,5.302 0.25,0.323 10 false (L) 5.198,4.833 5.469,5.083 0.271,0.25 10 false (G) 1.896,4.833 2.156,5.083 0.26,0.25 10 false (F) 0.292,3.917 0.542,4.167 0.25,0.25 10 false (E) 0.26,5.021 0.49,5.281 0.229,0.26 10 false (I) 1.75,6.354 2.063,6.635 0.313,0.281 10 false (J) 5.146,6.344 5.427,6.615 0.281,0.271 10 false (K)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right


Brake Actuator Operation in Auto LSD (When wheelspin of the rear right wheel occurs)
Item Auto LSD Activated
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) On (Closed) ← Off (Open)
Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve Port (B) Off (Closed) On (Open) ← Off (Closed)
Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve Port (G) Off (Open) On (Closed) ← ←
Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (K) Off (Closed) ← ← ←
Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve Port (E) Off (Open) On (Closed) ← ←
Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ← ← ←
Port (J) Off (Closed) ← ← ←




g.

VSC Operation

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure hold, and pressure increase modes. As a result, the tendency of the vehicle to experience a front wheel skid or rear wheel skid is controlled.


ii.

At this time, the skid control ECU outputs a VSC operation signal to the ECM and combination meter. Upon receiving this signal, the ECM controls the throttle to regulate the engine output. The slip indicator light will blink in the combination meter.


iii.

Front Wheel Skid Restraining Control (Right Turn)

·

For front wheel skid restraining control, the brakes of the rear wheel of the inner side of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

·

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn.

·

In other operating modes, the pressure holding valves and the pressure reduction valves are turned on/off according to a pattern that suits ABS with EBD operation.

X131038C01
0.51,2.635 1.469,3 true 2.333,2.729 2.844,3.01 true 4.792,2.708 4.333,3 true 5.708,3.021 6.573,2.646 true 5.708,4.344 6.625,4.031 true 5.188,4.875 4.771,4.323 true 2.01,4.833 2.396,4.323 true 0.51,4.052 1.458,4.333 true 0.427,5.156 1.458,5.417 true 1.844,6.354 2.396,5.417 true 5.219,6.344 4.781,5.406 true 6.656,5.104 5.708,5.406 true 3.229,5.115 3.583,5.958 3.583,5.958 3.948,5.115 true 3.229,6.5 3.615,7.063 3.615,7.063 3.948,6.5 true 3.01,0.885 3.229,1.115 0.219,0.229 10 false *1 0.74,1.469 0.969,1.667 0.229,0.198 10 false *2 5.167,1.875 5.385,2.115 0.219,0.24 10 false *3 1.406,3.542 1.656,3.781 0.25,0.24 10 false *4 2.771,3.531 3.031,3.729 0.26,0.198 10 false *5 1.396,4.865 1.646,5.094 0.25,0.229 10 false *6 1.406,5.948 1.604,6.208 0.198,0.26 10 false *7 3.51,5.979 3.729,6.229 0.219,0.25 10 false *8 3.542,7.073 3.76,7.313 0.219,0.24 10 false *9 1.396,7.396 1.615,7.646 0.219,0.25 10 false *a 2.323,7.406 2.5,7.646 0.177,0.24 10 false *b 4.719,7.406 4.99,7.615 0.271,0.208 10 false *c 5.656,7.406 5.906,7.656 0.25,0.25 10 false *d 5.656,3.552 5.906,3.792 0.25,0.24 10 false *4 4.271,3.542 4.531,3.74 0.26,0.198 10 false *5 2.354,4.875 2.604,5.104 0.25,0.229 10 false *6 4.719,4.865 4.969,5.094 0.25,0.229 10 false *6 5.688,4.865 5.938,5.094 0.25,0.229 10 false *6 2.344,5.948 2.542,6.208 0.198,0.26 10 false *7 4.729,5.948 4.927,6.208 0.198,0.26 10 false *7 5.635,5.948 5.833,6.208 0.198,0.26 10 false *7 0.302,2.49 0.542,2.781 0.24,0.292 10 false (A) 2.115,2.573 2.354,2.854 0.24,0.281 10 false (B) 4.823,2.573 5.094,2.875 0.271,0.302 10 false (C) 6.615,2.521 6.896,2.823 0.281,0.302 10 false (D) 6.667,3.906 6.938,4.188 0.271,0.281 10 false (H) 6.688,4.979 6.938,5.302 0.25,0.323 10 false (L) 5.198,4.833 5.469,5.083 0.271,0.25 10 false (G) 1.896,4.833 2.156,5.083 0.26,0.25 10 false (F) 0.292,3.917 0.542,4.167 0.25,0.25 10 false (E) 0.26,5.021 0.49,5.281 0.229,0.26 10 false (I) 1.75,6.354 2.063,6.635 0.313,0.281 10 false (J) 5.146,6.344 5.427,6.615 0.281,0.271 10 false (K)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right


Brake Actuator Operation in VSC (Front Wheel Skid Restraining)
Item VSC Activated
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) On (Closed) ← Off (Open)
Port (D) Off (Open) ← ← ←
Reservoir Cut Solenoid Valve Port (B) Off (Closed) On (Open) ← Off (Closed)
Port (C) Off (Closed) ← ← ←
Front Brake Pressure Holding Solenoid Valve Port (G) Off (Open) On (Closed) ← ←
Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (K) Off (Closed) ← ← ←
Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve Port (E) Off (Open) On (Closed) ← ←
Port (F) Off (Open) ← On (Closed) Off (Open)
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ← ← ←
Port (J) Off (Closed) ← ← ←



iv.

Rear Wheel Skid Restraining Control (Right Turn)

·

For rear wheel skid restraining control, the brake of the front wheel of the outer side of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if those wheels are targeted for braking.

·

The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn.

·

In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.

X131039C01
0.552,2.74 1.458,3.021 true 2.365,2.708 2.833,3 true 4.333,3 4.76,2.698 true 5.708,3 6.531,2.646 true 5.719,4.344 6.552,4.01 true 4.771,4.333 5.229,4.823 true 1.958,4.813 2.396,4.333 true 0.563,4.115 1.458,4.333 true 0.479,5.198 1.458,5.438 true 1.927,6.323 2.396,5.417 true 5.208,6.333 4.771,5.406 true 5.698,5.427 6.594,5.083 true 3.219,5.104 3.573,5.844 3.573,5.844 3.917,5.083 true 3.198,6.521 3.573,7.031 3.573,7.031 3.906,6.531 true 3.01,0.885 3.25,1.115 0.24,0.229 10 false *1 0.729,1.469 0.99,1.688 0.26,0.219 10 false *2 5.115,1.885 5.375,2.094 0.26,0.208 10 false *3 5.646,3.573 5.927,3.823 0.281,0.25 10 false *4 2.771,3.542 2.958,3.771 0.188,0.229 10 false *5 1.385,4.885 1.677,5.083 0.292,0.198 10 false *6 4.688,5.948 4.917,6.156 0.229,0.208 10 false *7 3.51,5.896 3.74,6.146 0.229,0.25 10 false *8 3.51,7.052 3.719,7.313 0.208,0.26 10 false *9 1.375,7.406 1.646,7.656 0.271,0.25 10 false *a 2.323,7.427 2.563,7.688 0.24,0.26 10 false *b 4.698,7.396 4.948,7.625 0.25,0.229 10 false *c 5.625,7.406 5.875,7.656 0.25,0.25 10 false *d 1.375,3.563 1.656,3.813 0.281,0.25 10 false *4 4.281,3.552 4.469,3.781 0.188,0.229 10 false *5 4.698,4.875 4.99,5.073 0.292,0.198 10 false *6 5.688,4.885 5.979,5.083 0.292,0.198 10 false *6 5.677,5.969 5.969,6.167 0.292,0.198 10 false *7 2.292,5.958 2.583,6.156 0.292,0.198 10 false *7 1.385,5.948 1.615,6.188 0.229,0.24 10 false *7 2.375,4.896 2.667,5.094 0.292,0.198 10 false *6 0.333,2.604 0.594,2.906 0.26,0.302 10 false (A) 4.802,2.563 5.063,2.844 0.26,0.281 10 false (C) 6.573,2.521 6.833,2.781 0.26,0.26 10 false (D) 6.583,3.896 6.844,4.115 0.26,0.219 10 false (H) 5.188,4.833 5.448,5.052 0.26,0.219 10 false (G) 1.844,4.823 2.104,5.042 0.26,0.219 10 false (F) 0.333,3.969 0.594,4.281 0.26,0.313 10 false (E) 0.313,5.052 0.531,5.323 0.219,0.271 10 false (I) 1.823,6.333 2.052,6.573 0.229,0.24 10 false (J) 5.146,6.344 5.427,6.583 0.281,0.24 10 false (K) 6.635,4.958 6.896,5.26 0.26,0.302 10 false (L) 2.146,2.563 2.406,2.865 0.26,0.302 10 false (B)
*1 Master Cylinder *2 Brake Actuator
*3 Master Cylinder Pressure Sensor *4 Master Cylinder Cut Solenoid Valve
*5 Reservoir Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pressure Reduction Solenoid Valve *8 Pumps
*9 Reservoirs - -
*a Rear Left *b Rear Right
*c Front Left *d Front Right


Brake Actuator Operation in VSC (Front Wheel Skid Restraining)
Item VSC Activated
Not Activated Pressure Increase Mode Pressure Holding Mode Pressure Reduction Mode
Master Cylinder Cut Solenoid Valve Port (A) Off (Open) ← ← ←
Port (D) Off (Open) On (Closed) ← Off (Open)
Reservoir Cut Solenoid Valve Port (B) Off (Closed) ← ← ←
Port (C) Off (Closed) On (Open) ← Off (Closed)
Front Brake Pressure Holding Solenoid Valve Port (G) Off (Open) ← On (Closed) Off (Open)
Port (H) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (K) Off (Closed) ← ← ←
Port (L) Off (Closed) ← ← ←
Rear Brake Pressure Holding Solenoid Valve Port (E) Off (Open) On (Closed) ← ←
Port (F) Off (Open) On (Closed) ← ←
Pressure Reduction Solenoid Valve Port (I) Off (Closed) ← ← ←
Port (J) Off (Closed) ← ← ←




h.

Trailer Sway Control Operation

i.

The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.



i.

Engine Output Control

i.

During a VSC operation, the skid control ECU outputs an engine output control request signal to the ECM. Upon receiving this signal, the ECM effects throttle control to regulate the engine output.

X128289E01
5.448,0.031 7.156,0.302 1.708,0.271 9 false (a): Start of engine control 5.448,0.583 7.125,0.833 1.677,0.25 9 false (c): Brake control completed 5.448,0.302 7.135,0.563 1.688,0.26 9 false (b): Start of brake control 5.448,0.865 7.146,1.156 1.698,0.292 9 false (d): Engine control completed 0.063,1.052 1.406,2.302 1.344,1.25 9 false Vehicle Condition (Front Wheel Skid or Rear Wheel Skid Level) 0.063,2.708 1.104,3.094 1.042,0.385 9 false Engine Torque 0.052,4.052 1.365,4.854 1.313,0.802 9 false Brake Wheel Cylinder Fluid Pressure* 1.406,4.865 1.729,5.177 0.323,0.313 9 false Low 1.417,3.427 1.719,3.76 0.302,0.333 9 false Low 1.417,1.948 1.719,2.281 0.302,0.333 9 false Low 1.406,0.792 1.74,1.125 0.333,0.333 9 false High 1.396,2.292 1.698,2.625 0.302,0.333 9 false High 1.406,3.75 1.729,4.094 0.323,0.344 9 false High 5.24,5.021 5.646,5.417 0.406,0.396 9 false Time 5.229,3.583 5.635,3.979 0.406,0.396 9 false Time 5.146,2.104 5.552,2.5 0.406,0.396 9 false Time 0.167,5.417 4.969,5.771 4.802,0.354 9 false *: The wheel cylinder that activates varies depending on the condition of the vehicle. 2.229,0.635 2.448,0.844 0.219,0.208 9 false (a) 2.5,0.646 2.719,0.854 0.219,0.208 9 false (b) 4.188,0.646 4.406,0.854 0.219,0.208 9 false (c) 4.458,0.646 4.677,0.854 0.219,0.208 9 false (d)



j.

Initial Check

i.

Each time the ignition switch is turned on, and the vehicle reaches approximately speed of 23 km/h (14.3 mph) or more, the skid control ECU performs an initial check.


ii.

The functions of each solenoid valve and pump motor in the brake actuator are checked in sequence.




Self-Diagnosis


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTCs and check function, refer to the Repair Manual.



Fail-Safe


a.

If a failure occurs in the skid control ECU, sensors or brake actuator assembly, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.