Home › General › CHASSIS › TRANSFER
NM27M0U _V1 General _050232 CHASSIS _0242381 TRANSFER UN GENERAL/CONTROL/DETAILS F

CHASSIS  TRANSFER  GENERAL/CONTROL/DETAILS  4WD CONTROL SYSTEM  


General


a.

The 4WD system used allows the driver to select the appropriate mode from among the 3 drive modes by utilizing the 4WD control switch. In addition, the Automatic Disconnecting Differential (A.D.D.) operates after the 4WD control ECU detects that the transfer shift actuator is in the 4H position by receiving a signal from the limit switch of the transfer shift actuator.


b.

Through the 4WD control switch signal, the 4WD control ECU actuates the electromagnetic clutch solenoid, the shift motor in the transfer shift actuator and the shift motor in the A.D.D. shift actuator.



System Diagram


X129482E01
4.052,2.677 4.458,0.844 4.458,0.844 4.604,0.844 true 3.917,2.281 3.792,0.948 3.792,0.948 3.667,0.948 true 2.021,2.271 1.563,1.146 1.563,1.146 1.406,1.146 true 3.688,2.708 3.604,2.958 3.604,2.958 3.458,2.958 true 4.729,0.479 6.188,0.833 1.458,0.354 10 false Transfer Shift Actuator 4.688,0.76 6.146,1.115 1.458,0.354 10 false - Transfer Shift Motor 4.688,1.01 6.042,1.24 1.354,0.229 10 false - Limit Switch 2.635,0.771 3.646,1.375 1.01,0.604 10 false Electromagnetic Clutch Solenoid 0.073,1.042 1.417,1.417 1.344,0.375 10 false A.D.D. Shift Actuator 0.063,1.333 1.406,1.708 1.344,0.375 10 false - A.D.D. Shift Motor 0.063,1.625 1.406,2 1.344,0.375 10 false - Limit Switch 0.063,1.948 1.719,2.281 1.656,0.333 10 false - A.D.D. Detection Switch 2.719,2.823 3.469,3.542 0.75,0.719 10 false L4 Position Switch 5.073,3.688 6.75,4.073 1.677,0.385 10 false 4WD Control Switch 3.083,3.688 4.76,4.073 1.677,0.385 10 false 4WD Control ECU 4.51,4.344 6.188,4.729 1.677,0.385 10 false Combination Meter 4.563,4.875 6.24,5.26 1.677,0.385 10 false 4HI Indicator Light 4.479,5.417 6.156,5.802 1.677,0.385 10 false 4LO Indicator Light 4.656,5.969 6.333,6.354 1.677,0.385 10 false Multi Buzzer 1.313,4.333 2.99,4.719 1.677,0.385 10 false Skid Control ECU 1.177,4.729 2.677,5 1.5,0.271 10 false - Vehicle Speed Signal 3.031,5.563 4.052,5.958 1.021,0.396 10 false CAN (V Bus) 1.708,5.292 3.208,5.563 1.5,0.271 10 false ECM 1.188,5.677 2.688,5.948 1.5,0.271 10 false - Engine Speed Signal 1.188,5.948 2.688,6.219 1.5,0.271 10 false - Shift Position Signal


Wiring Diagram


X129483E01
2.969,0.302 3.281,0.5 0.313,0.198 10 false +B 3.469,0.302 3.781,0.5 0.313,0.198 10 false IG 4.052,1.156 4.365,1.354 0.313,0.198 10 false H4 4.052,1.656 4.365,1.854 0.313,0.198 10 false L4 2.635,1.042 2.948,1.24 0.313,0.198 10 false LO 2.625,1.417 2.938,1.615 0.313,0.198 10 false 2-4 5.24,2.052 6.427,2.458 1.188,0.406 10 false L4 Position Switch 1.594,1.25 1.906,1.448 0.313,0.198 10 false 4H 1.885,1.396 2.25,1.667 0.365,0.271 10 false 2WD 1.271,1.406 1.635,1.677 0.365,0.271 10 false 4L 0.344,1.885 1.615,2.177 1.271,0.292 10 false 4WD Control Switch 5.188,2.906 6.375,3.313 1.188,0.406 10 false A.D.D. Shift Motor 0.531,2.906 1.802,3.302 1.271,0.396 10 false Transfer Shift Motor 4.052,2.823 5.24,3.229 1.188,0.406 10 false DM1 4.063,3.281 5.25,3.688 1.188,0.406 10 false DM2 4.094,3.667 5.281,4.073 1.188,0.406 10 false DL1 4.083,4.083 5.271,4.49 1.188,0.406 10 false DL2 4.083,4.646 5.271,5.052 1.188,0.406 10 false ADD 5.448,4.125 6.635,4.531 1.188,0.406 10 false Limit Switch 5.073,4.688 6.625,5.01 1.552,0.323 10 false A.D.D. Detection Switch 5.156,5.052 6.708,5.375 1.552,0.323 10 false A.D.D. Shift Actuator 3.052,4.313 3.875,4.99 0.823,0.677 10 false 4WD Control ECU 2.51,2.813 3.698,3.219 1.188,0.406 10 false TM1 2.51,3.229 3.698,3.635 1.188,0.406 10 false TM2 2.521,3.667 3.708,4.073 1.188,0.406 10 false TL1 2.531,4.031 3.146,4.281 0.615,0.25 10 false TL2 2.542,4.375 3.156,4.625 0.615,0.25 10 false TL3 2.542,4.719 3.156,4.969 0.615,0.25 10 false TL4 2.552,5.083 3.167,5.333 0.615,0.25 10 false GTL 0.698,5.229 1.604,5.458 0.906,0.229 10 false Limit Switch 0.333,5.615 1.76,5.958 1.427,0.344 10 false Transfer Shift Actuator 5.646,5.604 6.469,5.906 0.823,0.302 10 false ECM 5.313,6.156 6.479,6.469 1.167,0.313 10 false Skid Control ECU 5.219,7.104 6.438,7.427 1.219,0.323 10 false Combination Meter 5.083,7.771 6.292,8.135 1.208,0.365 10 false CAN (V Bus) 3.51,8.333 4.729,8.656 1.219,0.323 10 false GND 2.531,6.344 3.75,6.667 1.219,0.323 10 false SCC 0.073,6.781 2.156,7.156 2.083,0.375 10 false Electromagnetic Clutch Solenoid


Layout of Main Components


X129484C01
4.448,3.438 4.26,2.771 true 2.396,3.688 2.771,3.146 true 5.76,4.542 6.135,4 true 0.573,5.74 1,5.542 true 4.823,6.083 5.406,5.5 true 6.698,6.25 6.396,5.906 true 2.219,3.594 2.531,3.75 0.313,0.156 10 false *1 4.406,3.438 4.719,3.594 0.313,0.156 10 false *2 0.375,5.646 0.688,5.802 0.313,0.156 10 false *3 4.656,5.969 4.969,6.125 0.313,0.156 10 false *4 6.729,6.167 7.042,6.323 0.313,0.156 10 false *5 6.146,3.813 6.458,3.969 0.313,0.156 10 false *6
*1 Front Differential *2 Transfer
*3 A.D.D. Shift Actuator (Differential Vacuum Actuator Assembly)
·

A.D.D. Shift Motor

·

Limit Switch

·

A.D.D. Detection Switch


*4 L4 Position Switch (Transfer Indicator Switch)
*5 Transfer Shift Actuator Assembly
·

Transfer Shift Motor

·

Limit Switch


*6 Electromagnetic Clutch Solenoid (Solenoid Coil Sub-assembly)


X129485C01
5.708,0.948 6.031,0.729 true 2.729,2.115 2.354,1.167 true 1.75,2.146 2.146,1.188 true 6.25,3.646 5.531,3.354 true 1.594,2.104 1.906,2.26 0.313,0.156 10 false *1 2.729,2.125 3.042,2.281 0.313,0.156 10 false *2 6.292,3.563 6.604,3.719 0.313,0.156 10 false *3 6.063,0.583 6.375,0.74 0.313,0.156 10 false *4
*1 4LO Indicator Light *2 4HI Indicator Light
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 4WD Control Switch (Transfer Position Switch)



System Operation


a.

General

i.

The drive mode switching pattern of this system is as shown in the illustration below:


ii.

2WD-4WD switching (switching patterns A and B) is available while driving.


iii.

High-low switching of the transfer gear ratio (switching patterns C, D and E) is available only when the vehicle is stationary, the brake pedal is held down, and the shift lever is in N.


iv.

When the 4WD control ECU detects that the 4WD control switch has been operated while a mode switching restriction condition is satisfied, it prohibits shifting and informs the driver by blinking the 4HI indicator light or 4LO indicator light and sounding the multi buzzer in the combination meter.

Drive Mode Switching Pattern
X129486E01
2.573,1.604 2.729,1.802 0.156,0.198 10 false A 3.052,1.948 3.208,2.146 0.156,0.198 10 false B 4.458,1.573 4.615,1.771 0.156,0.198 10 false C 4.073,1.979 4.229,2.177 0.156,0.198 10 false D 3.51,2.708 3.667,2.906 0.156,0.198 10 false E

Switching Pattern 4WD Control Switch Operation
A 2WD → 4H
B 4H → 2WD
C 4H → 4L
D 4L → 4H
E 4L → 2WD



b.

Switching Pattern A (2WD → 4H)

i.

When the 4WD control switch is turned from the 2WD to 4H position, a signal is received by the 4WD control ECU, which actuates the electromagnetic clutch solenoid, transfer shift motor and A.D.D. shift motor.

·

Electricity is supplied to the electromagnetic clutch solenoid, thereby synchronizing the front driveline and rear driveline.

·

The transfer shift motor rotates the transfer shifter to the 4H position. At this time, the transfer shifter moves the 2-4 shift fork rearward together with the 4-wheel drive lock-up hub. As a result, the operation of the 4-wheel drive lock-up hub connects the front driveline and rear driveline, changing the mode to 4H.

·

The A.D.D. shift motor then operates to activate 4WD mode. When the shift actuator is engaged, the electromagnetic clutch solenoid stops operation.

·

The 4WD control ECU detects the state of the transfer shift actuator and the A.D.D. shift actuator through the limit switch and the A.D.D. detection switch. The 4HI indicator light turns on after switching from 2WD to 4H mode has been completed.

X129487C01
5.458,5.552 5.396,5.281 true 1.76,5.083 2.073,5.24 0.313,0.156 10 false *2 4.594,2.604 4.906,2.76 0.313,0.156 10 false *3 5.823,0.625 6.135,0.781 0.313,0.156 10 false *4 5.823,1.031 6.135,1.188 0.313,0.156 10 false *5 6.073,3.219 6.385,3.375 0.313,0.156 10 false *6 5.385,5.573 5.844,5.792 0.458,0.219 10 false *7 (*i) 2.281,0.104 2.594,0.26 0.313,0.156 10 false *a 2.292,0.323 2.604,0.479 0.313,0.156 10 false *b 2.302,0.531 2.615,0.688 0.313,0.156 10 false *c 3.521,2.198 3.833,2.354 0.313,0.156 10 false *d 0.156,2.719 0.469,2.875 0.313,0.156 10 false *e 1.052,4.229 1.365,4.385 0.313,0.156 10 false *f 3.083,2.698 3.458,2.969 0.375,0.271 10 false *g 4.979,1.479 5.292,1.635 0.313,0.156 10 false *h 3.542,2.896 3.854,3.052 0.313,0.156 10 false *b 3.583,3.719 3.896,3.875 0.313,0.156 10 false *c 1.198,1.667 1.51,1.823 0.313,0.156 10 false *1
*1 Front Differential *2 Transfer
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 Combination Meter
*5 4HI Indicator Light *6 4WD Control Switch (Transfer Position Switch)
*7 2-4 Shift Fork (No. 2 Transfer Gear Shift Fork Sub-assembly) - -
*a A.D.D. Detection Switch Signal *b Limit Switch Signal
*c Motor Actuate Signal *d Solenoid Actuate Signal
*e Input *f Front Output
*g Rear Output *h CAN (V Bus)
*i 2WD Position → 4H Position - -


Operation Flow
X129488E01
2.542,0.344 4.688,0.625 2.146,0.281 10 false 4WD Control Switch: 2WD → 4H 2.323,1.177 4.99,1.573 2.667,0.396 10 false Electromagnetic Clutch Solenoid Turns On 2.656,1.927 4.906,2.219 2.25,0.292 10 false Transfer Shift Motor Actuates 2.49,2.219 5.156,2.615 2.667,0.396 10 false - 2-4 Shift Fork Moves: 2WD → 4H 1.875,2.979 5.573,3.333 3.698,0.354 10 false Limit Switch of Transfer Shift Actuator Detects 4H Position 2.719,3.781 6.417,4.135 3.698,0.354 10 false A.D.D. Shift Motor Actuates 0.844,4.531 6.542,4.938 5.698,0.406 10 false Limit Switch of A.D.D. Shift Actuator Detects 4WD Position and A.D.D. Detection Switch On 2.26,5.354 4.948,5.656 2.688,0.302 10 false Electromagnetic Clutch Solenoid Turns Off 2.646,6.156 5.333,6.458 2.688,0.302 10 false 4HI Indicator Light Turns On




c.

Switching Pattern B (4H → 2WD)

i.

When the 4WD control switch is turned from the 4H to 2WD position, a signal is received by the 4WD control ECU, which actuates the transfer shift motor and A.D.D. shift motor.

·

The transfer shift motor rotates the transfer shifter to the 2WD position. At this time, the transfer shifter moves the 2-4 shift fork frontward together with the 4-wheel drive lock-up hub. As a result, the operation of the 4-wheel drive lock-up hub disconnects the front driveline and rear driveline, changing the mode to 2WD.

·

The A.D.D. shift motor then operates to activate 2WD mode.

·

The 4WD control ECU detects the state of the transfer shift actuator and the A.D.D. shift actuator through the limit switch and the A.D.D. detection switch. The 4HI indicator light turns off after switching from 4H to 2WD mode has been completed.

X129489C01
5.448,5.563 5.302,5.292 true 1.146,1.656 1.458,1.813 0.313,0.156 10 false *1 1.531,5.042 1.844,5.198 0.313,0.156 10 false *2 4.594,2.615 4.906,2.771 0.313,0.156 10 false *3 5.802,0.615 6.115,0.771 0.313,0.156 10 false *4 5.802,1.021 6.115,1.177 0.313,0.156 10 false *5 6.021,3.24 6.333,3.396 0.313,0.156 10 false *6 5.385,5.542 5.854,5.76 0.469,0.219 10 false *7 (*g) 2.365,0.073 2.677,0.229 0.313,0.156 10 false *a 2.385,0.313 2.698,0.469 0.313,0.156 10 false *b 2.396,0.531 2.708,0.688 0.313,0.156 10 false *c 0.177,2.719 0.521,2.938 0.344,0.219 10 false *d 3.115,2.698 3.427,2.854 0.313,0.156 10 false *e 5.01,1.469 5.323,1.625 0.313,0.156 10 false *f 3.573,2.885 3.885,3.042 0.313,0.156 10 false *b 3.625,3.708 3.938,3.865 0.313,0.156 10 false *c
*1 Front Differential *2 Transfer
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 Combination Meter
*5 4HI Indicator Light *6 4WD Control Switch (Transfer Position Switch)
*7 2-4 Shift Fork (No. 2 Transfer Gear Shift Fork Sub-assembly) - -
*a A.D.D. Detection Switch Signal *b Limit Switch Signal
*c Motor Actuate Signal *d Input
*e Rear Output *f CAN (V Bus)
*g 4H Position → 2WD Position - -



Operation Flow
X129490E01
2.49,0.177 4.625,0.615 2.135,0.438 10 false 4WD Control Switch: 4H → 2WD 2.583,0.938 4.719,1.375 2.135,0.438 10 false Transfer Shift Motor Actuates 2.563,1.219 4.698,1.656 2.135,0.438 10 false - 2-4 Shift Fork Moves: 4H → 2WD 1.885,1.927 5.615,2.302 3.729,0.375 10 false Limit Switch of Transfer Shift Actuator Detects 2WD Position 2.604,2.719 4.521,2.99 1.917,0.271 10 false A.D.D. Shift Motor Actuates 0.781,3.531 6.458,3.906 5.677,0.375 10 false Limit Switch of A.D.D. Shift Actuator Detects 2WD Position and A.D.D. Detection Switch Off 2.594,4.333 4.396,4.74 1.802,0.406 10 false 4HI Indicator Light Turns Off



d.

Switching Pattern C (4H → 4L)

i.

When the 4WD control switch is turned from the 4H to 4L position, a signal is received by the 4WD control ECU, which actuates the transfer shift motor.

·

The transfer shift motor rotates the transfer shifter to the 4L position. At this time, the transfer shifter moves the H-L shift fork rearward together with the reduction hub. As a result, the reduction hub engages the planetary carrier, changing the mode to 4L.

·

The 4WD control ECU detects the state of the transfer shift actuator through the limit switch and the L4 position switch. The 4HI indicator light turns off and the 4LO indicator light turns on after switching from 4H to 4L mode has been completed.

X129491C01
5.24,5.406 5.156,5.073 true 1.76,0.521 2.073,0.677 0.313,0.156 10 false *1 1.781,4.042 2.094,4.198 0.313,0.156 10 false *2 4.573,2.708 4.885,2.865 0.313,0.156 10 false *3 5.854,0.719 6.167,0.875 0.313,0.156 10 false *4 5.854,1.125 6.167,1.281 0.313,0.156 10 false *5 5.854,1.5 6.167,1.656 0.313,0.156 10 false *6 6.042,3.333 6.354,3.49 0.313,0.156 10 false *7 0.167,1.625 0.479,1.781 0.313,0.156 10 false *a 0.979,3.156 1.292,3.313 0.313,0.156 10 false *b 3.115,1.635 3.427,1.792 0.313,0.156 10 false *c 3.354,2.802 3.667,2.958 0.313,0.156 10 false *d 3.375,3.177 3.688,3.333 0.313,0.156 10 false *e 4.969,1.708 5.281,1.865 0.313,0.156 10 false *f 5.125,5.406 5.604,5.729 0.479,0.323 10 false *8 (*g)
*1 L4 Position Switch (Transfer Indicator Switch) *2 Transfer
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 Combination Meter
*5 4HI Indicator Light *6 4LO Indicator Light
*7 4WD Control Switch (Transfer Position Switch) *8 H-L Shift Fork (No. 1 Transfer Gear Shift Fork Sub-assembly)
*a Input *b Front Output
*c Rear Output *d Limit Switch Signal
*e Motor Actuate Signal *f CAN (V Bus)
*g 4H Position → 4L Position - -


Operation Flow
X129492E01
2.615,0.448 4.573,0.927 1.958,0.479 10 false 4WD Control Switch: 4H → 4L 2.667,1.24 4.542,1.531 1.875,0.292 10 false Transfer Shift Motor Actuates 2.573,1.479 4.646,1.781 2.073,0.302 10 false - H-L Shift Fork Moves: 4H → 4L 1.063,2.219 6.292,2.594 5.229,0.375 10 false Limit Switch of Transfer Shift Actuator Detects 4L Position and L4 Position Switch On 1.76,3.021 6.99,3.396 5.229,0.375 10 false 4HI Indicator Light Turns Off and 4LO Indicator Light Turns On




e.

Switching Pattern D (4L → 4H)

i.

When the 4WD control switch is turned from the 4L to 4H position, a signal is received by the 4WD control ECU, which actuates the transfer shift motor.

·

The transfer shift motor rotates the transfer shifter to the 4H position. At this time, the transfer shifter moves the H-L shift fork frontward together with the reduction hub. As a result, the reduction hub engages the input shaft, changing the mode to 4H.

·

The 4WD control ECU detects the state of the transfer shift actuator through the limit switch and the L4 position switch. The 4LO indicator light turns off and the 4HI indicator light turns on after switching from 4L to 4H mode has been completed.

X129493C01
5.083,5.385 4.958,5.052 true 1.771,0.51 2.083,0.667 0.313,0.156 10 false *1 1.573,3.948 1.885,4.104 0.313,0.156 10 false *2 4.583,2.688 4.896,2.844 0.313,0.156 10 false *3 5.823,0.719 6.135,0.875 0.313,0.156 10 false *4 5.844,1.146 6.156,1.302 0.313,0.156 10 false *5 5.854,1.521 6.167,1.677 0.313,0.156 10 false *6 6.073,3.323 6.385,3.479 0.313,0.156 10 false *7 5.01,5.396 5.583,5.75 0.573,0.354 10 false *8 (*g) 0.146,1.635 0.458,1.792 0.313,0.156 10 false *a 1,3.156 1.313,3.313 0.313,0.156 10 false *b 3.125,1.656 3.438,1.813 0.313,0.156 10 false *c 3.323,2.854 3.635,3.01 0.313,0.156 10 false *d 3.354,3.177 3.667,3.333 0.313,0.156 10 false *e 4.948,1.625 5.26,1.781 0.313,0.156 10 false *f
*1 L4 Position Switch (Transfer Indicator Switch) *2 Transfer
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 Combination Meter
*5 4HI Indicator Light *6 4LO Indicator Light
*7 4WD Control Switch (Transfer Position Switch) *8 H-L Shift Fork (No. 1 Transfer Gear Shift Fork Sub-assembly)
*a Input *b Front Output
*c Rear Output *d Limit Switch Signal
*e Motor Actuate Signal *f CAN (V Bus)
*g 4H Position → 4L Position - -


Operation Flow
X129494E01
2.563,0.427 4.667,0.813 2.104,0.385 10 false 4WD Control Switch: 4L → 4H 2.635,1.219 4.563,1.469 1.927,0.25 10 false Transfer Shift Motor Actuates 2.5,1.542 5.073,1.833 2.573,0.292 10 false - H-L Shift Fork Moves: 4L → 4H 1.083,2.229 6.313,2.583 5.229,0.354 10 false Limit Switch of Transfer Shift Actuator Detects 4H Position and L4 Position Switch Off 1.677,3.01 5.542,3.323 3.865,0.313 10 false 4LO Indicator Light Turns Off and 4HI Indicator Light Turns On




f.

Switching Pattern E (4L → 2WD)

i.

When the 4WD control switch is turned from the 4L to 2WD position, a signal is received by the 4WD control ECU. Then, the 4WD control ECU actuates the transfer shift motor and A.D.D. shift motor. The switching operation changes in the following sequence: 4L → 4H → 2WD (switching pattern D → B).

X129495C01
1.521,6.542 1.719,6.281 true 5.635,6.531 5.417,6.24 true 1.135,1.625 1.448,1.781 0.313,0.156 10 false *1 1.51,5.083 1.823,5.24 0.313,0.156 10 false *2 4.563,2.521 4.875,2.677 0.313,0.156 10 false *3 5.802,0.531 6.115,0.688 0.313,0.156 10 false *4 5.813,0.927 6.125,1.083 0.313,0.156 10 false *5 5.823,1.333 6.135,1.49 0.313,0.156 10 false *6 6.042,3.146 6.354,3.302 0.313,0.156 10 false *7 5.854,3.729 6.167,3.885 0.313,0.156 10 false *8 1.094,6.458 1.5,6.708 0.406,0.25 10 false *9 (*g) 5.698,6.479 6.354,6.729 0.656,0.25 10 false *10 (*h) 2.219,0.01 2.531,0.167 0.313,0.156 10 false *a 2.229,0.219 2.542,0.375 0.313,0.156 10 false *b 2.24,0.427 2.552,0.583 0.313,0.156 10 false *c 0.135,2.792 0.448,2.948 0.313,0.156 10 false *d 3.125,2.771 3.438,2.927 0.313,0.156 10 false *e 3.531,2.646 3.844,2.802 0.313,0.156 10 false *b 3.573,4.073 3.885,4.229 0.313,0.156 10 false *c 4.958,1.344 5.271,1.5 0.313,0.156 10 false *f
*1 Front Differential *2 Transfer
*3 4WD Control ECU (4 Wheel Drive Control ECU) *4 Combination Meter
*5 4HI Indicator Light *6 4LO Indicator Light
*7 4WD Control Switch (Transfer Position Switch) *8 L4 Position Switch (Transfer Indicator Switch)
*9 H-L Shift Fork (No. 1 Transfer Gear Shift Fork Sub-assembly) *10 2-4 Shift Fork (No. 2 Transfer Gear Shift Fork Sub-assembly)
*a A.D.D. Detection Switch Signal *b Limit Switch Signal
*c Motor Actuate Signal *d Input
*e Rear Output *f CAN (V Bus)
*g 4L Position → 4H Position *h 4H Position → 2WD Position


Operation Flow
X129496E01
2.5,0.365 4.583,0.708 2.083,0.344 10 false 4WD Control Switch: 4L → 2WD 2.615,1.135 4.698,1.479 2.083,0.344 10 false Transfer Shift Motor Actuates 2.51,1.427 4.594,1.771 2.083,0.344 10 false - H-L Shift Fork Moves: 4L → 4H 0.99,2.177 6.385,2.469 5.396,0.292 10 false Limit Switch of Transfer Shift Actuator Detects 4H Position and L4 Position Switch Off 1.698,2.958 5.604,3.26 3.906,0.302 10 false 4LO Indicator Light Turns Off and 4HI Indicator Light Turns On 2.542,3.74 4.552,4.01 2.01,0.271 10 false Transfer Shift Motor Actuates 2.385,4.031 4.729,4.26 2.344,0.229 10 false - 2-4 Shift Fork Moves: 4H → 2WD 1.802,4.781 5.573,5.135 3.771,0.354 10 false Limit Switch of Transfer Shift Actuator Detects 2WD Position 2.698,5.552 6.469,5.906 3.771,0.354 10 false A.D.D. Shift Motor Actuates 0.813,6.333 6.438,6.719 5.625,0.385 10 false Limit Switch of A.D.D. Shift Actuator Detects 2WD Position and A.D.D. Detection Switch Off 2.698,7.146 4.583,7.427 1.885,0.281 10 false 4HI Indicator Light Turns Off




Diagnosis


a.

If the 4WD control ECU detects a malfunction in the 4WD control system, it will make the 4HI indicator light and 4LO indicator light blink to warn the driver. The 4WD control ECU will also store the Diagnostic Trouble Codes (DTCs) in memory.


b.

5-digit DTCs can be read by connecting a Techstream to the DLC3. For details, refer to the Repair Manual.



Fail-safe


a.

If a malfunction occurs in the signal system of the 4WD control system, the 4WD control ECU disables the 4WD control.