Home › General › CHASSIS › AB60E / AB60F AUTOMATIC TRANSMISSION
NM27M0U _V1 General _050232 CHASSIS _0242499 AB60E / AB60F AUTOMATIC TRANSMISSION UN GENERAL/CONTROL/DETAILS F

CHASSIS  AB60E / AB60F AUTOMATIC TRANSMISSION  GENERAL/CONTROL/DETAILS  ELECTRONIC CONTROL SYSTEM  


GENERAL


a.

The electronic control system of the AB60E and AB60F automatic transmissions consists of the control functions listed below.

System Function
Shift Timing Control The ECM sends current to solenoid valves S1, S2, S3, S4 and/or SR based on signals from various sensors, in order to shift the gears.
Clutch Pressure Control
·

Controls the pressure that is applied directly to B2 brake and C3 clutch by actuating the linear solenoid valves SL1 and SL2 in accordance with the ECM signals.

·

The solenoid valve SLT and SL1 minutely controls the clutch pressure in accordance with the engine output and driving conditions.


Line Pressure Optimal Control Actuates the solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission.
Engine Torque Control Retards the engine ignition timing temporarily to improve shift feeling while upshifts or downshifts occur.
Lock-up Timing Control The ECM sends current to the solenoid valve SLU based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control Controls the solenoid valve SLU, provides an intermediate mode for when the lock-up clutch is between ON and OFF, increasing the operating range of the lock-up clutch to improve fuel economy.
Powertrain Cooperative Control Controls both the shift control and engine output control in an integrated way, achieving excellent shift characteristics and drivability.
Coast Downshift Control To prevent engine speed from decreasing and thereby maintain fuel cut, the ECM performs downshifts before fuel cut ends.
Tow/Haul Control To ensure drivability when a trailer is towed, the ECM controls the engine output, transmission shift schedule and shift timing.
AI (Artificial Intelligence) -SHIFT Control Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, thus improving drivability.
Multi-Mode Automatic Transmission The ECM appropriately controls the automatic transmission in accordance with the range position selected while the shift lever is in the S mode position.
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information that relates to the fault.
Fail-safe If a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's drivability from being affected significantly.



CONSTRUCTION


a.

The configurations of the electronic control system for the AB60E and AB60F automatic transmissions are as shown in the following chart.

X131649E01
2.708,0.167 3.031,0.365 0.323,0.198 10 false VG 2.667,1.917 3.125,2.115 0.458,0.198 10 false VTA1 2.667,2.156 3.115,2.396 0.448,0.24 10 false VTA2 2.719,1.042 3.031,1.24 0.313,0.198 10 false NE 0.625,0.208 2.438,0.542 1.813,0.333 10 false MASS AIR FLOW METER 0.583,0.948 2.281,1.552 1.698,0.604 10 false CRANKSHAFT POSITION SENSOR 0.458,1.979 2.552,2.313 2.094,0.333 10 false THROTTLE POSITION SENSOR 0.656,2.719 2.208,3.333 1.552,0.615 10 false ACCELERATOR PEDAL POSITION SENSOR 0.635,3.656 2.292,4.271 1.656,0.615 10 false ENGINE COOLANT TEMP ERATURE SENSOR 0.479,4.594 2.469,5.219 1.99,0.625 10 false ATF TEMPERATURE SENSOR NO. 1 0.49,5.542 2.458,6.156 1.969,0.615 10 false ATF TEMPERATURE SENSOR NO. 2 0.458,6.479 2.281,7.083 1.823,0.604 10 false PARK/NEUTRAL POSITION SWITCH 0.615,7.521 2.365,8.281 1.75,0.76 10 false TRANSMISSION CONTROL SWITCH 2.625,3.042 3.073,3.302 0.448,0.26 10 false VPA2 2.656,2.813 3.052,3.031 0.396,0.219 10 false VPA 2.667,3.75 3.042,3.948 0.375,0.198 10 false THW 2.656,4.677 3.094,4.885 0.438,0.208 10 false THO1 2.646,5.615 3.083,5.823 0.438,0.208 10 false THO2 2.656,6.563 3.063,6.781 0.406,0.219 10 false NSW 2.635,6.813 3.031,7.417 0.396,0.604 10 false P, R, N, D 2.698,7.688 3.125,7.875 0.427,0.188 10 false SFTU 2.708,7.927 3.115,8.125 0.406,0.198 10 false SFTD 4.135,7.354 4.542,7.646 0.406,0.292 10 false IGF2 4.115,6.708 4.542,7.125 0.427,0.417 10 false IGT 2, 3, 5, 8 5.083,6.896 6.333,7.542 1.25,0.646 10 false IGNITION COIL with IGNITER 5.229,7.563 6.219,7.854 0.99,0.292 10 false No. 2, 3, 5, 8 5.177,8.031 6.292,8.333 1.115,0.302 10 false SPARK PLUGS 5.146,5.708 6.344,6.01 1.198,0.302 10 false SPARK PLUGS 5.24,5.229 6.313,5.5 1.073,0.271 10 false No. 1, 4, 6, 7 5.073,4.573 6.313,5.198 1.24,0.625 10 false IGNITION COIL with IGNITER 4.135,5.031 4.531,5.302 0.396,0.271 10 false IGF1 4.104,4.417 4.552,4.813 0.448,0.396 10 false IGT 1, 4, 6, 7 5.51,4.177 6.052,4.458 0.542,0.281 10 false ESA 4.979,3.677 6.656,3.99 1.677,0.313 10 false SOLENOID VALVE SLU 5.021,3.25 6.615,3.563 1.594,0.313 10 false SOLENOID VALVE SLT 5.01,2.813 6.625,3.115 1.615,0.302 10 false SOLENOID VALVE SR 5.01,2.375 6.635,2.677 1.625,0.302 10 false SOLENOID VALVE SL2 4.969,1.948 6.625,2.24 1.656,0.292 10 false SOLENOID VALVE SL1 4.979,1.51 6.5,1.802 1.521,0.292 10 false SOLENOID VALVE S4 4.958,1.073 6.531,1.375 1.573,0.302 10 false SOLENOID VALVE S3 4.917,0.208 6.563,0.531 1.646,0.323 10 false SOLENOID VALVE S1 4.938,0.646 6.448,0.948 1.51,0.302 10 false SOLENOID VALVE S2 4.094,0.167 4.365,0.365 0.271,0.198 10 false S1 4.094,0.594 4.365,0.792 0.271,0.198 10 false S2 4.083,1.031 4.375,1.25 0.292,0.219 10 false S3 4.094,1.469 4.375,1.667 0.281,0.198 10 false S4 4.094,1.896 4.427,2.094 0.333,0.198 10 false SL1 4.083,2.323 4.417,2.542 0.333,0.219 10 false SL2 4.083,2.75 4.365,2.969 0.281,0.219 10 false SR 4.104,3.177 4.438,3.396 0.333,0.219 10 false SLT 4.094,3.625 4.427,3.844 0.333,0.219 10 false SLU 5.229,6.01 6.302,6.281 1.073,0.271 10 false No. 1, 4, 6, 7 5.521,6.5 6.063,6.781 0.542,0.281 10 false ESA 5.219,8.344 6.208,8.635 0.99,0.292 10 false No. 2, 3, 5, 8 2.865,7.427 3.083,7.635 0.219,0.208 10 false S

X131627E01
0.688,0.667 2.521,0.969 1.833,0.302 10 false INPUT SPEED SENSOR 0.688,1.479 2.542,1.792 1.854,0.313 10 false OUTPUT SPEED SENSOR 0.771,2.302 2.438,2.604 1.667,0.302 10 false STOP LIGHT SWITCH 0.781,3.125 2.5,3.438 1.719,0.313 10 false 4WD CONTROL ECU*1 0.458,4.542 2.469,5.167 2.01,0.625 10 false TOW/HAUL PATTERN SELECT SWITCH*2 2.708,0.625 3,0.813 0.292,0.188 10 false NT 2.677,1.417 3.063,1.615 0.385,0.198 10 false SP2 2.677,2.25 3.094,2.458 0.417,0.208 10 false STP 2.729,3.073 3.052,3.281 0.323,0.208 10 false L4 2.635,4.625 3.073,4.844 0.438,0.219 10 false TOW 4.083,4.927 4.427,5.25 0.344,0.323 10 false TC 4.083,1.021 4.396,1.229 0.313,0.208 10 false W 4.073,0.573 4.479,0.792 0.406,0.219 10 false SPD 4.906,0.177 6.531,0.531 1.625,0.354 10 false COMBINATION METER 4.813,0.667 6.542,1 1.729,0.333 10 false VEHICLE SPEED SIGNAL 5.552,1.094 6,1.396 0.448,0.302 10 false MIL 4.802,1.531 6.188,2.156 1.385,0.625 10 false ATF TEMPERATURE WARNING LIGHT 4.76,2.167 6.51,2.76 1.75,0.594 10 false SHIFT RANGE INDICATOR LIGHT 4.75,2.802 6.563,3.104 1.813,0.302 10 false S MODE INDICATOR LIGHT 4.781,3.177 6.313,3.771 1.531,0.594 10 false TOW/HAUL INDICATOR LIGHT*2 5.448,4.615 6.135,4.969 0.688,0.354 10 false DLC3 3.375,2.385 3.865,2.844 0.49,0.458 10 false ECM 0.292,5.281 2.198,5.656 1.906,0.375 10 false *1: 4WD Models 2.438,5.292 4.531,5.656 2.094,0.365 10 false *2: Models with towing package 4.406,4.146 5.583,4.563 1.177,0.417 10 false CAN (V Bus)



LAYOUT OF MAIN COMPONENTS


X131628C01
2.917,0.854 2.927,0.365 true 3.458,1.229 3.802,0.344 true 2.854,0.177 3.167,0.375 0.313,0.198 10 false *1 3.76,0.167 4.073,0.365 0.313,0.198 10 false *2
*1 ECM *2 Throttle Body
·

Throttle Position Sensor

·

Throttle Control Motor




X131629C01
2.271,1.844 1.927,0.365 true 2.167,1.917 1.51,0.438 true 2.052,2.042 1.094,0.625 true 1.896,2.063 0.708,0.844 true 1,3.167 1.938,2.302 true 2.229,3.365 2.229,2.448 true 2.802,1.979 2.802,3.125 true 3.083,2.938 3.083,1.958 true 5.094,3.271 5.094,2.479 true 5.625,2.438 6.198,2.948 true 5.813,1.823 5.813,0.521 true 2.646,1.708 3.115,0.542 true 2.479,1.729 2.771,0.323 true 2.365,1.781 2.396,0.292 true 1.813,0.167 2.125,0.365 0.313,0.198 10 false *1 1.385,0.26 1.698,0.458 0.313,0.198 10 false *2 0.948,0.438 1.26,0.635 0.313,0.198 10 false *3 0.542,0.677 0.854,0.875 0.313,0.198 10 false *4 0.833,3.156 1.146,3.354 0.313,0.198 10 false *5 2.156,3.406 2.469,3.604 0.313,0.198 10 false *6 2.719,3.156 3.031,3.354 0.313,0.198 10 false *7 3.01,2.99 3.323,3.188 0.313,0.198 10 false *8 2.281,0.104 2.594,0.302 0.313,0.198 10 false *11 2.688,0.156 3,0.354 0.313,0.198 10 false *10 3.063,0.344 3.375,0.542 0.313,0.198 10 false *9 5.688,0.333 6,0.531 0.313,0.198 10 false *14 6.219,2.958 6.531,3.156 0.313,0.198 10 false *13 5,3.292 5.313,3.49 0.313,0.198 10 false *12
*1 Solenoid Valve S1 *2 Solenoid Valve SR
*3 Solenoid Valve SL1 *4 Solenoid Valve SLT
*5 ATF Temperature Sensor No.1 (THO1) *6 ATF Temperature Sensor No.2 (THO2)
*7 Solenoid Valve SL2 *8 Solenoid Valve SLU
*9 Solenoid Valve S3 *10 Solenoid Valve S2
*11 Solenoid Valve S4 *12 Output Speed Sensor (SP2)
*13 Park/Neutral Position Switch *14 Input Speed Sensor (NT)


X131630C01
4.448,1.708 4.677,0.813 true 4.031,2.156 3.531,3.865 true 4.292,2.979 4.042,4 true 2.729,1.5 2.417,0.51 true 4.688,1.708 5.427,1.063 true 5.792,4.115 4.854,3.573 true 3.406,2.854 3.167,3.844 true 3.063,2.875 2.385,3.771 true 2.198,3.677 2.51,3.875 0.313,0.198 10 false *2 2.313,0.323 2.625,0.521 0.313,0.198 10 false *1 5.906,2.354 6.51,2.698 0.604,0.344 10 false *7 (*A) 5.865,4.031 6.177,4.229 0.313,0.198 10 false *6 3.948,4.031 4.26,4.229 0.313,0.198 10 false *5 3.438,3.865 3.75,4.063 0.313,0.198 10 false *4 3.063,3.854 3.708,4.167 0.646,0.313 10 false *3 5.469,0.906 6.156,1.229 0.688,0.323 10 false *8 (*A) 4.625,0.615 4.865,0.833 0.24,0.219 10 false *9
*A Models with Towing Package - -
*1 Combination Meter *2 DLC3
*3 Stop Light Switch *4 Shift Lock ECU (Column Shift Only)
*5 Accelerator Pedal Position Switch *6 Floor Shift Lever Assembly (Floor Shift Models Only)
·

Transmission Control Switch

·

Shift Lock ECU


*7 TOW/HAUL Pattern Select Switch (Floor Shift Only) *8 TOW/HAUL Pattern Select Switch (Column Shift Only)
*9 Column Shift Lever (Column ShiftModels Only)
·

Transmission Control Switch


- -



CONSTRUCTION AND OPERATION OF MAIN COMPONENTS


a.

ATF Temperature Sensor No.1 and No.2

i.

ATF temperature sensor No.1 (THO1) is used for hydraulic pressure control. This sensor is used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.


ii.

ATF temperature sensor No.2 (THO2) is used as a basis for modifying the ECT shift timing control when the ATF temperature is high. It is also used for the ATF temperature warning light.

X128188C01
3.281,1.615 2.927,0.531 true 3.01,3.323 3.25,2.438 true 2.813,0.354 3.073,0.604 0.26,0.25 10 false *1 2.917,3.354 3.177,3.604 0.26,0.25 10 false *2 1.469,1.802 1.729,2.052 0.26,0.25 10 false *a
*1 ATF Temperature Sensor No. 1 (THO1) *2 ATF Temperature Sensor No. 2 (THO2)
*a Front - -




b.

Input Speed Sensor and Output Speed Sensor

i.

The AB60E and AB60F automatic transmissions use an input speed sensor (for NT signal) and output speed sensor (for SP2 signal). Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions.


ii.

These speed sensors are the pick-up coil type.

·

The input speed sensor detects the input speed of the transmission. The clutch drum is used as the timing rotor for this sensor.

·

The output speed sensor detects the speed of the output shaft. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.


X128189C01
2.5,1.188 1.844,0.396 true 2.281,1.594 1.49,2.188 true 3.667,1.885 4.219,3.24 true 4.604,0.417 4.104,1.365 true 1.677,0.271 1.958,0.542 0.281,0.271 10 false *1 1.344,2.198 1.625,2.469 0.281,0.271 10 false *2 4.188,3.26 4.469,3.531 0.281,0.271 10 false *3 4.583,0.26 4.865,0.531 0.281,0.271 10 false *4
*1 Parking Gear (Timing Rotor) *2 Output Speed Sensor
*3 Input Speed Sensor *4 C3 Clutch Drum (Timing Rotor)




c.

Park/Neutral Position Switch

i.

The park/neutral position switch sends the P, R, N, D and NSW position signals to the ECM. It also sends signals for the shift position indicator light (P, R, N, and D).

Wiring Diagram
X128190E02
3.958,2.125 5.198,2.448 1.24,0.323 10 false Combination Meter 4.375,0.385 4.698,0.688 0.323,0.302 10 false ECM 0.479,0.813 1.5,1.156 1.021,0.344 10 false To Starter Relay 1.344,1.583 1.604,1.781 0.26,0.198 10 false +B 2.656,0.781 2.917,0.979 0.26,0.198 10 false B 2.646,1.031 2.906,1.229 0.26,0.198 10 false PL 2.656,1.25 2.917,1.448 0.26,0.198 10 false RL 2.646,1.49 2.906,1.688 0.26,0.198 10 false NL 2.646,1.729 2.906,1.927 0.26,0.198 10 false DL 3.292,0.75 3.635,0.938 0.344,0.188 10 false NSW 3.927,0.75 4.188,0.948 0.26,0.198 10 false P 4.365,0.75 4.625,0.948 0.26,0.198 10 false R 4.792,0.75 5.052,0.948 0.26,0.198 10 false N 5.208,0.74 5.469,0.938 0.26,0.198 10 false D 3.938,1.896 4.198,2.094 0.26,0.198 10 false P 4.344,1.896 4.604,2.094 0.26,0.198 10 false R 4.781,1.896 5.042,2.094 0.26,0.198 10 false N 5.208,1.896 5.469,2.094 0.26,0.198 10 false D 1.292,2.281 3.292,2.646 2,0.365 10 false Park/Neutral Position Switch 1.656,0.76 1.938,0.958 0.281,0.198 10 false L



d.

Transmission Control Switch

i.

The transmission control switch is installed inside the shift lever assembly to detect the shift lever position and to inform the ECM. The ECM turns on the shift position indicator light and S mode indicator light.


ii.

The transmission control switch detects whether the shift lever is in the D position or in the S mode position, and detects the operating conditions of the shift lever ("+" position or "-" position) if the S mode is selected, and sends signals to the ECM. At this time, the ECM turns on the shift range indicator light for the selected range.

Wiring Diagram
X128191E03
1.99,0.51 3.75,0.844 1.76,0.333 10 false Transmission Control Switch 4.594,0.396 5.75,0.74 1.156,0.344 10 false To IG No. 1 Relay 3.448,2.76 3.833,3.063 0.385,0.302 10 false ECM 3.375,3.323 4.594,3.646 1.219,0.323 10 false Combination Meter 3.271,3.75 4.698,4.094 1.427,0.344 10 false S Mode Indicator Light 3.219,4.208 5.052,4.531 1.833,0.323 10 false Shift Range Indicator Light 4.49,0.708 4.698,0.896 0.208,0.188 10 false IG 1.25,3.76 2.208,4.177 0.958,0.417 10 false CAN (V Bus) 2.125,1.104 2.333,1.292 0.208,0.188 10 false E 2.323,1.823 2.698,2.073 0.375,0.25 10 false SFTD 3.135,1.823 3.552,2.115 0.417,0.292 10 false SFTU 4.323,1.823 4.531,2.01 0.208,0.188 10 false S 2.729,2.292 3.104,2.542 0.375,0.25 10 false SFTD 3.615,2.292 4.042,2.531 0.427,0.24 10 false SFTU 4.479,2.292 4.688,2.479 0.208,0.188 10 false S



e.

TOW/HAUL Pattern Select Switch

i.

The TOW/HAUL pattern select switch is a momentary-type switch.

·

If the shift lever is in the D position when the switch is pushed once, tow/haul control will be performed. If the TOW/HAUL pattern select switch is operated again, or the ignition switch is turned off, tow haul control will be cancelled.

·

The TOW/HAUL pattern select switch and the TOW/HAUL indicator light are provided for the towing package.


X131631C01
3.26,0.896 3.26,0.406 true 3.177,0.219 3.49,0.417 0.313,0.198 10 false *1 2.49,1.438 2.802,1.635 0.313,0.198 10 false *a 4.823,1.469 5.135,1.667 0.313,0.198 10 false *b
*1 TOW/HAUL Pattern Select Switch - -
*a Column Shift Type *b Floor Shift Type





CLUTCH PRESSURE CONTROL


a.

Clutch to Clutch Pressure Control

i.

This control is used for shifting from 5th to 6th gear and from 6th to 5th gear.


ii.

The ECM actuates solenoid valves SL1 and SL2 in accordance with various signals. The output from these solenoid valves acts directly on control valves B2 and C3 in order to regulate the line pressure that acts on the B2 brake and C3 clutch.


iii.

As a result, high response and excellent shift characteristics have been realized.

X128192E01
2.385,0.833 2.719,1.125 0.333,0.292 10 false ECM 1.74,1.188 2.031,1.479 0.292,0.292 10 false SL1 3.344,1.188 3.677,1.479 0.333,0.292 10 false SL2 0.594,2.552 0.927,2.844 0.333,0.292 10 false C3 3.969,2.448 4.302,2.74 0.333,0.292 10 false B2 1.802,2.615 2.625,3.271 0.823,0.656 10 false Clutch Control Valve 1.021,3.51 1.885,3.813 0.865,0.302 10 false Line Pressure 4.99,3.438 5.521,3.625 0.531,0.188 10 false 5th→6th 5.677,3.135 5.885,3.323 0.208,0.188 10 false C3 6.156,3.135 6.365,3.333 0.208,0.198 10 false B2 4.521,0.917 5.948,1.229 1.427,0.313 10 false - Output Speed Sensor 3.469,1.719 4.375,2.333 0.906,0.615 10 false Brake Control Valve 5,3.885 5.531,4.073 0.531,0.188 10 false 6th→5th 5.677,3.406 5.896,3.719 0.219,0.313 10 false Off 6.177,3.854 6.396,4.167 0.219,0.313 10 false Off 6.146,3.417 6.365,3.729 0.219,0.313 10 false On 5.698,3.854 5.917,4.167 0.219,0.313 10 false On 4.521,0.563 5.813,0.885 1.292,0.323 10 false - Input Speed Sensor 4.521,1.26 6.083,1.563 1.563,0.302 10 false - Throttle Position Sensor 4.531,1.583 5.927,1.875 1.396,0.292 10 false - Mass Air Flow Meter 4.521,1.906 6.552,2.208 2.031,0.302 10 false - ATF Temperature Sensor No. 1 4.531,2.25 6.875,2.573 2.344,0.323 10 false - Engine Coolant Temperature Sensor 4.531,2.604 6.76,2.948 2.229,0.344 10 false - Accelerator Pedal Position Sensor



b.

Clutch Pressure Optimal Control

i.

The ECM monitors the signals from various types of sensors, such as the input speed sensor, allowing shift solenoid valves SLT and SL1 to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are realized.

X128193E01
2.75,4.75 2.927,4.75 2.927,4.75 3.135,4.354 true 3.781,4.302 4.969,4.021 4.969,4.021 5.094,4.021 true 2.979,3.313 4.771,2.365 4.771,2.365 4.917,2.365 true 4.24,3.333 4.667,2.99 4.667,2.99 4.865,2.99 true 3.542,4.313 3.208,4.896 3.208,4.896 3.646,4.896 true 4.375,1.313 4.719,1.615 0.344,0.302 10 false ECM 1.656,0.479 2.5,1.125 0.844,0.646 10 false Target rpm Change Ratio 0.167,0.396 0.427,0.698 0.26,0.302 10 false rpm 0.115,0.917 0.469,1.656 0.354,0.74 10 false Input Shaft 0.552,1.521 2.25,1.854 1.698,0.333 10 false Practical rpm Change Ratio 1.792,1.875 2.125,2.167 0.333,0.292 10 false Time 4.938,2.938 6.292,3.25 1.354,0.313 10 false Output Speed Sensor 0.094,5.26 0.667,6.417 0.573,1.156 10 false Clutch Brake Pressure 1.104,4.677 2.75,5.01 1.646,0.333 10 false Accumulator Control Valve 3.688,4.833 4.698,5.5 1.01,0.667 10 false Solenoid Valves SL1, SLT 5.135,3.969 7.073,4.281 1.938,0.313 10 false ATF Temperature Sensor No. 1 3.875,5.542 4.708,6.188 0.833,0.646 10 false Output Shaft Torque 6.573,6.375 6.917,6.677 0.344,0.302 10 false Time 0.833,6.323 2.188,6.677 1.354,0.354 10 false Solenoid Drive Signal 5,2.292 6.25,2.625 1.25,0.333 10 false Input Speed Sensor




LINE PRESSURE OPTIMAL CONTROL


a.

Through the use of the solenoid valve SLT, the line pressure is optimally controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transmission.


b.

Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition, and ATF temperature, thus realizing smooth shift characteristics and optimizing the workload of the oil pump (reducing unnecessary parasitic losses).

X128194E03
0.719,3.76 0.646,3.49 0.646,3.49 0.521,3.49 true 3.854,2.969 4.167,3.188 4.167,3.188 4.396,3.188 false 0.375,0.708 1.24,1.01 0.865,0.302 10 false Line Pressure 0.906,1.875 2.417,2.188 1.51,0.313 10 false Primary Regulator Valve 1.875,2.677 2.438,3.333 0.563,0.656 10 false Fluid Pressure 2.667,3.313 3.188,3.615 0.521,0.302 10 false Current 0.125,3.406 0.5,3.708 0.375,0.302 10 false Pump 3.083,4.135 4.323,4.458 1.24,0.323 10 false Solenoid Valve SLT 2.031,3.771 3.104,4.115 1.073,0.344 10 false Throttle Pressure 4.438,3.115 5.792,3.5 1.354,0.385 10 false Solenoid Drive Signal 5.042,0.438 6.448,0.781 1.406,0.344 10 false Throttle Valve Opening 5.042,0.792 6.198,1.115 1.156,0.323 10 false Intake Air Volume 5.042,1.156 6.823,1.5 1.781,0.344 10 false Engine Coolant Temperature 5.042,1.521 6,1.854 0.958,0.333 10 false Engine Speed 5.042,1.875 5.906,2.177 0.865,0.302 10 false Input Speed 5.042,2.25 6.167,2.604 1.125,0.354 10 false ATF Temperature 5.042,2.615 5.917,2.917 0.875,0.302 10 false Shift Position 4.219,1.417 4.656,1.781 0.438,0.365 10 false ECM



LOCK-UP TIMING CONTROL


a.

The ECM operates the lock-up timing control in order to improve the fuel consumption performance while in top gear with the shift lever in the S4 or S5 range, and in 5th or 6th gear with the shift lever in the S6 range or D position.

Lock-Up Timing in D Position or S6 Range
X128195E02
3.958,2.063 3.094,1.146 3.094,1.146 2.927,1.146 true 0.833,0.469 1.219,0.792 0.385,0.323 10 false Large 0.115,1.552 1.021,2.26 0.906,0.708 10 false Throttle Opening Angle 1.823,1.042 2.906,1.865 1.083,0.823 10 false 5th Lock-up Operating Range 3.375,3.354 4.292,3.698 0.917,0.344 10 false Vehicle Speed 4.708,2.302 5.74,2.958 1.031,0.656 10 true 6th Lock-up Operating Range 5.875,3.135 6.26,3.458 0.385,0.323 10 false High

Lock-up Operation Gears in Each Range

○: Available

x: Not available

-: Not applicable

*: Lock-up operation is performed when the 4th gear is help during the AI-SHIFT control or the cruise control.

Shift Position or Shift Range D, S6 S5 S4
Gear 1st X X X
2nd X X X
3rd X X X
4th X* X* ○
5th ○ ○ -
6th ○ - -



FLEX LOCK-UP CLUTCH CONTROL


a.

In the low-to-mid-speed range, this flex lock-up clutch control regulates the solenoid valve SLU to provide an intermediate mode between the ON/OFF operation of the lock-up clutch in order to improve the energy transmitting efficiency in this range.


b.

As a result, the operating range of the lock-up clutch has been increased and fuel economy has been improved. The flex lock-up clutch control operates in the 3rd, 4th, 5th and 6th gears in the D position and S6 range, 3rd, 4th and 5th gears in the S5 range, 3rd and 4th gear in the S4 range.

i.

Even when the vehicle is decelerating (the accelerator pedal is released), the flex lock-up clutch control operates. Therefore, fuel-cut area of the engine has been expanded and fuel-economy has been improved.

X128196E01
2.979,4.208 3.219,3.677 3.219,3.677 3.323,3.677 true 3.281,5.458 3.031,5.458 3.031,5.458 3.406,4.958 true 2.615,5.365 2.771,5.365 2.771,5.365 3.083,4.99 true 5.042,5.396 4.885,5.396 4.885,5.396 3.583,4.948 true 1.135,2.677 1.365,2.677 1.365,2.677 1.563,3.094 true 2.021,1.677 2.25,1.677 2.25,1.677 2.281,2.01 false 0.99,4.469 1.094,4.469 1.094,4.469 1.083,4.031 true 5.167,4.135 5.438,4.135 false 4.99,4.615 5.406,4.615 false 6.052,1.177 5.948,1.729 5.948,1.729 5.74,1.729 false 5.948,1.083 5.844,0.188 5.844,0.188 6.01,0.188 false 0.531,1.448 0.292,0.875 0.292,0.875 0.438,0.875 false 3.198,0.25 3.542,0.552 0.344,0.302 10 false ECM 0.5,0.792 1.719,1.458 1.219,0.667 10 false Engine Coolant Temperature Signal 0.583,2.604 1.135,3.74 0.552,1.135 10 false Throttle Position Sensor 0.052,4.333 0.948,5.521 0.896,1.188 10 false Engine Coolant Temperature Sensor 2.698,2.438 3.521,3.177 0.823,0.74 10 false Engine Speed Signal 3.531,2.469 4.281,3.542 0.75,1.073 10 false Input Speed Sensor Signal 5.469,4.521 6.979,4.917 1.51,0.396 10 false ATF Temperature Signal 5.49,4.031 6.875,4.417 1.385,0.385 10 false Linear Solenoid Signal 6.729,3.5 7.094,3.802 0.365,0.302 10 false Time 5.74,3.01 7.135,3.354 1.396,0.344 10 false Linear Solenoid Signal 4.979,2.563 5.667,2.906 0.688,0.344 10 false Duty Ratio 6.167,1.625 7.083,1.958 0.917,0.333 10 false Vehicle Speed 4.844,1.635 5.708,2.333 0.865,0.698 10 false Input Turbine Speed Signal 6.052,0.115 6.927,0.729 0.875,0.615 10 false Engine Speed Signal 5.229,0.375 5.677,1.083 0.448,0.708 10 false Engine Speed 1.229,5.26 2.583,5.583 1.354,0.323 10 false Lock-up Control Valve 3.354,5.344 4.604,5.656 1.25,0.313 10 false Solenoid Valve SLU 5.094,5.313 7.031,5.635 1.938,0.323 10 false ATF Temperature Sensor No. 1 3.375,3.604 4.167,4.24 0.792,0.635 10 false Input Speed Sensor 0.573,1.604 2.021,1.938 1.448,0.333 10 false Throttle Position Signal

X128197E01
1.208,0.563 1.573,0.896 0.365,0.333 10 false Large 2.135,0.688 3.729,1.031 1.594,0.344 10 false : Lock-up operating range 0.542,1.75 1.583,2.438 1.042,0.688 10 false Throttle Opening Angle 5.323,3.188 5.688,3.521 0.365,0.333 10 false High 3.271,3.188 4.229,3.542 0.958,0.354 10 false Vehicle Speed 2.135,1.406 4.823,1.76 2.688,0.354 10 false : Flex lock-up operating range (deceleration) 2.135,1.052 4.823,1.417 2.688,0.365 10 false : Flex lock-up operating range (acceleration)

Flex Lock-up Operation Gears in Each Range

○: Available

x: Not available

-: Not applicable

*: Flex Lock-up also operates, when the vehicle is decelerating

Shift Position or Shift Range D, S6 S5 S4
Gear 1st X X X
2nd X X X
3rd ○ ○ ○
4th ○* ○* ○*
5th ○* ○* -
6th ○* - -




POWERTRAIN COOPERATIVE CONTROL


a.

Through cooperative control with ETCS-i (Electronic Throttle Control System-intelligent) and ESA (Electronic Spark Advance), and electronic control of the engagement and release speed of the clutch and brake hydraulic pressures, excellent response and shift shock reduction have been achieved.

X128198E01
1.76,0.344 2.708,0.979 0.948,0.635 10 false Driver's desired drive force 3.771,1.396 4.146,1.729 0.375,0.333 10 false ECM 3.281,2.104 4.656,3.094 1.375,0.99 10 false Optimal clutch engagement hydraulic pressure and timing 5.01,1.854 5.938,2.625 0.927,0.771 10 false Solenoid Valve Control Signal 5.125,3.083 6.042,3.771 0.917,0.688 10 false Solenoid Valve (SL1, SL2) 1.969,2.333 2.906,2.656 0.938,0.323 10 false ETCS-i Control 1.458,4.698 2.406,5.333 0.948,0.635 10 false Optimal engine output 4.625,4.854 5.896,5.49 1.271,0.635 10 false Driver's desired drive force is achieved 2.115,2.688 2.938,3.01 0.823,0.323 10 false ESA Control



COAST DOWNSHIFT CONTROL


a.

As a result of coast downshift control, downshifts are performed to maintain sufficient engine speed to avoid ending fuel cut control. Thus, fuel cut time is extended and fuel economy is achieved.

i.

In this control, the transmission downshifts from 6th to 5th and then 5th to 4th before fuel cut control ends when the vehicle is decelerated in the 6th gear, so that fuel cut control continues operating.

X131634E01
3.771,0.917 3.771,0.406 3.771,0.406 3.563,0.406 true 3.198,2.781 3.073,2.396 true 3.563,2.781 3.646,2.375 true 3.375,3.042 3.625,2.938 true 4.115,3.083 4.198,3 true 2.25,0.313 3.542,0.906 1.292,0.594 10 false Continuous Fuel Cut Control Operation 0.885,0.917 2.208,1.24 1.323,0.323 10 false Fuel Cut Control ON 0.813,1.198 2.229,1.583 1.417,0.385 10 false Fuel Cut Control OFF 1.698,1.802 2.146,2.74 0.448,0.938 10 false Engine Speed 2.26,2.271 2.719,2.49 0.458,0.219 10 false 6th 2.875,2.219 3.333,2.5 0.458,0.281 10 false to 5th 3.469,2.198 3.927,2.396 0.458,0.198 10 false to 4th 2.979,3 3.438,3.198 0.458,0.198 10 false to 5th 3.813,3.083 4.271,3.281 0.458,0.198 10 false to 4th 4.583,3.313 4.979,3.625 0.396,0.313 10 false Time 4.896,3 6.51,3.323 1.615,0.323 10 false Fuel Cut Control OFF 4.833,2.094 6.542,2.51 1.708,0.417 10 false Fuel Cut Control ON 4.979,0.427 6.792,0.729 1.813,0.302 10 false : with Downshift Control 4.99,0.698 6.865,1.063 1.875,0.365 10 false : without Downshift Control




TOW/HAUL CONTROL


a.

General

i.

During tow/haul control, the ECM controls the engine output, transmission shift schedule and shift timing to ensure drivability when a trailer is towed. The tow/haul control includes a throttle control, shift schedule control, wide open throttle shift timing control and AI-SHIFT control.

1.

The conditions required for tow/haul control to operate are as follows:

·

Shift position: D position (Tow/haul control does not operate in the S position).

·

TOW/HAUL pattern select switch: ON


2.

The TOW/HAUL indicator light is used to inform the driver that tow/haul control is operating.

X131635E01
1.625,4.073 1.625,3.813 1.625,3.813 1.49,3.813 true 3.323,5.354 3.396,4.771 3.396,4.771 3.5,4.771 true 4.292,5.354 4.365,4.771 4.365,4.771 4.479,4.771 true 3.208,0.208 4.698,0.542 1.49,0.333 10 false Combination Meter 2.938,0.667 4.833,1.01 1.896,0.344 10 false TOW/HAUL Indicator Light 3.938,1.229 5.125,1.563 1.188,0.333 10 false CAN (V Bus) 2.125,2.125 3.052,2.896 0.927,0.771 10 false Accelerator Position Signal 3.635,2.333 4.292,2.979 0.656,0.646 10 false ECM 2.833,3.49 3.302,4.708 0.469,1.219 10 false Input Speed Sensor Signal 3.802,3.479 4.281,4.594 0.479,1.115 10 false Output Speed Sensor Signal 4.875,3.479 5.458,4.677 0.583,1.198 10 false Solenoid Valve Control Signals 5.896,3.479 6.51,5.396 0.615,1.917 10 false Fluid Pressure Control Signals 3.542,4.656 4.292,5.26 0.75,0.604 10 false Input Speed Sensor 4.531,4.688 5.458,5.396 0.927,0.708 10 false Output Speed Sensor 0.615,3.729 1.469,4.188 0.854,0.458 10 false Throttle Body 1.208,2.823 1.698,3.708 0.49,0.885 10 false Throttle Control Signal




b.

Throttle Control

i.

Throttle control changes the relationship between the accelerator pedal depression angle and the throttle valve opening angle.

·

During tow/haul control, the throttle valve opening is increased by throttle control. As a result, acceleration performance is ensured.

X131605E02
1.927,0.313 2.385,0.771 0.458,0.458 10 false Wide 1.375,1.302 2.365,2.177 0.99,0.875 10 false Throttle Valve Opening Angle 2.469,0.406 4.333,0.948 1.865,0.542 10 false Tow/Haul Control: Operating 3.646,1.875 5.854,2.302 2.208,0.427 10 false Tow/Haul Control: Not Operating 2.875,2.438 5.083,2.792 2.208,0.354 10 false Accelerator Pedal Depression Angle




c.

Shift Schedule Control

i.

The shift schedule control changes the upshift and downshift schedules during tow/haul control.

·

For the upshift schedule, the upshift timing is changed to higher vehicle speeds, enhancing the use of lower gears. As a result, drivability is ensured.

Upshift Schedule
X131636E01
0.802,1.167 1.219,1.479 0.417,0.313 10 false Wide 0.625,1.844 1.198,3.26 0.573,1.417 10 false Throttle Valve Opening Angle 1.563,0.948 2.323,1.167 0.76,0.219 10 false 1st → 2nd 2.292,0.958 3.021,1.188 0.729,0.229 10 false 2nd → 3rd 3.146,0.979 3.906,1.219 0.76,0.24 10 false 3rd → 4th 4.115,0.958 4.844,1.198 0.729,0.24 10 false 4th → 5th 5.25,0.99 5.99,1.219 0.74,0.229 10 false 5th → 6th 4.698,0.146 6.979,0.458 2.281,0.313 10 false Tow/Haul Control: Not Operating 4.698,0.479 6.771,0.813 2.073,0.333 10 false Tow/Haul Control: Operating 5.5,3.354 6.01,3.667 0.51,0.313 10 false High 2.813,3.344 4.031,3.656 1.219,0.313 10 false Vehicle Speed



ii.

For the downshift schedule, the downshift timing is change to a wider throttle valve opening angle, enhancing the use of higher gears. As a result, the frequency of gear changes is reduced, allowing optimal shift quality.

Downshift Schedule
X131637E01
0.719,1.156 1.188,1.479 0.469,0.323 10 false Wide 0.583,1.875 1.156,3.271 0.573,1.396 10 false Throttle Valve Opening Angle 1.417,1.073 2.094,1.313 0.677,0.24 10 false 1st ← 2nd 2.115,1.063 2.854,1.271 0.74,0.208 10 false 2nd ← 3rd 2.875,1.073 3.646,1.333 0.771,0.26 10 false 3rd ← 4th 3.927,1.063 4.698,1.323 0.771,0.26 10 false 4th ← 5th 5.271,1.063 6.021,1.323 0.75,0.26 10 false 5th ← 6th 4.698,0.49 6.74,0.865 2.042,0.375 10 false Tow/Haul Control: Operating 4.688,0.146 6.917,0.49 2.229,0.344 10 false Tow/Haul Control: Not Operating 5.583,3.323 6.167,3.615 0.583,0.292 10 false High 2.708,3.333 3.896,3.656 1.188,0.323 10 false Vehicle Speed



d.

Wide Open Throttle Shift Timing Control

i.

Due to wide open throttle shift timing control, upshift timing is delayed to make use of high engine power when the accelerator pedal is fully opened.

·

Wide open throttle shift control operates in 1st, 2nd and 3rd during tow/haul control.

X131608E02
2.125,1.396 2.26,0.521 2.26,0.521 2.448,0.521 false 3.76,1.406 4.875,0.698 4.875,0.698 5.042,0.698 false 0.969,3.979 1.354,4.302 0.385,0.323 10 false High 0.958,2.677 1.344,3 0.385,0.323 10 false High 0.979,1.365 1.365,1.688 0.385,0.323 10 false High 0.844,1.865 1.323,2.604 0.479,0.74 10 false Engine Speed 0.365,1.396 0.667,1.719 0.302,0.323 10 false (a) 0.354,2.625 0.635,2.99 0.281,0.365 10 false (b) 0.365,3.833 0.656,4.198 0.292,0.365 10 false (c) 4.917,1.354 6.01,2.177 1.094,0.823 10 false Maximum Engine Speed 0.854,3.115 1.333,3.854 0.479,0.74 10 false Engine Speed 0.854,4.458 1.333,5.198 0.479,0.74 10 false Engine Speed 2.479,0.417 4.229,1.177 1.75,0.76 10 false Upshift Instruction (Tow/Haul Control: Not Operating) 5.094,0.604 6.875,1.354 1.781,0.75 10 false Upshift Instruction (Tow/Haul Control: Operating) 4.906,2.656 6.01,3.521 1.104,0.865 10 false Maximum Engine Speed 4.917,3.99 6.021,4.906 1.104,0.917 10 false Maximum Engine Speed 2.333,4.583 3.802,4.896 1.469,0.313 10 false Upshift Timing Change 4.698,5.156 5.135,5.5 0.438,0.344 10 false Time

- Heavy Load Tow/Haul Control
(a) Without Not Operating
(b) With Not Operating
(c) With Operating





AI-SHIFT CONTROL


a.

General

i.

In addition to shift pattern changes due to tow/haul control, AI (Artificial Intelligence) -SHIFT control determines optimal transmission control based on input signals and automatically changes the shift pattern. As a result, a high caliber of transmission operation is achieved.

·

The AI-SHIFT control includes a road condition support control and a driver's intention support control.

·

AI-SHIFT control is effect only with the shift lever in the D position, based on the accelerator and brake operation data. AI-SHIFT control will be canceled when the driver selects the S mode.

X131609E01
2.385,0.896 2.969,1.208 0.583,0.313 10 false AI-shift 2.479,1.417 3.531,1.75 1.052,0.333 10 false Road Condition 2.656,1.792 4.146,2.135 1.49,0.344 10 false Uphill/Downhill Driving 3.146,2.229 4.365,2.531 1.219,0.302 10 false Estimating Grade 2.354,2.792 2.813,3.177 0.458,0.385 10 false Small 4.604,2.844 5.042,3.188 0.438,0.344 10 false Large 2.74,3.167 4.302,3.49 1.563,0.323 10 false : Criterion acceleration 2.76,3.646 4.375,3.948 1.615,0.302 10 false : Actual acceleration 2.5,4.479 3.646,4.771 1.146,0.292 10 false Driver's Intention 0.333,3.479 1.594,3.917 1.26,0.438 10 false Calculated by ECM 0.271,3.917 1.604,4.25 1.333,0.333 10 false Vehicle Acceleration 0.281,2.5 1.479,2.844 1.198,0.344 10 false - Brake Signal 0.271,2.177 1.51,2.51 1.24,0.333 10 false - Engine Speed 0.271,1.854 1.458,2.188 1.188,0.333 10 false - Vehicle Speed 0.302,1.135 1.375,1.854 1.073,0.719 10 false - Throttle Valve Opening Angle 0.521,0.833 1.448,1.135 0.927,0.302 10 false Sensor Signal 0.542,0.125 1.427,0.49 0.885,0.365 10 false Input Signals 5.969,0.344 7,1.302 1.031,0.958 10 false Basic Shift Pattern Control 5.948,2.646 7,3.427 1.052,0.781 10 false Road Condition Support Control 5.896,5.385 6.906,6.365 1.01,0.979 10 false Driver's Intention Support Control 3.906,5.104 4.677,6.188 0.771,1.083 10 false Estimating Driver's Intention 2.333,4.802 3.375,5.531 1.042,0.729 10 false - Acceleration Pedal Operation 2.313,5.583 3.208,6.229 0.896,0.646 10 false - Vehicle Condition




b.

Road Condition Support Control

i.

Under road condition support control, the ECM determines throttle valve opening angle and the vehicle speed whether the vehicle is being driven uphill or downhill.

1.

When a trailer is not being towed

·

To achieve an optimal drive force while driving uphill, this control prevents the transmission from up-shifting to 4th, 5th or 6th gear.

·

To achieve an optimal engine braking effect while driving downhill, this control automatically downshifts the transmission to 5th, 4th or 3rd gear.

X128201E01
6.115,2.573 7.094,2.896 0.979,0.323 10 false Without Control 6.188,3.302 7.052,3.625 0.865,0.323 10 false With Control 1.135,3.25 1.354,3.427 0.219,0.177 10 false 6th 1.125,2.719 1.344,2.896 0.219,0.177 10 false 6th 1.729,2.719 1.948,2.896 0.219,0.177 10 false 4th 2.156,2.719 2.375,2.896 0.219,0.177 10 false 5th 2.51,2.719 2.729,2.896 0.219,0.177 10 false 3rd 2.5,3.26 2.719,3.438 0.219,0.177 10 false 3rd 1.948,3.25 2.167,3.427 0.219,0.177 10 false 4th 2.844,2.719 3.063,2.896 0.219,0.177 10 false 5th 3.229,2.719 3.448,2.896 0.219,0.177 10 false 4th 3.615,3.26 3.833,3.438 0.219,0.177 10 false 4th 4.677,3.271 4.896,3.448 0.219,0.177 10 false 3rd 5.146,3.271 5.365,3.448 0.219,0.177 10 false 4th 5.625,3.271 5.844,3.448 0.219,0.177 10 false 5th 5.906,3.26 6.125,3.438 0.219,0.177 10 false 6th 5.771,2.698 5.99,2.875 0.219,0.177 10 true 6th 3.552,2.552 5.604,2.865 2.052,0.313 10 true 5th (Driver needs to apply brakes)


2.

When a trailer is being towed

·

To achieve an optimal drive force while driving uphill, this control prevents the transmission from up-shifting.

·

To achieve an optimal engine braking effect while driving downhill, this control automatically downshifts the transmission.

·

In addition to the shift pattern changes due to the road condition support control, the shift pattern is further changed when the tow/haul control is turned ON.

X131611E01
2.042,2.719 2.302,2.146 true 5.396,2.667 5.74,2.875 0.344,0.208 10 false 6th 0.438,2.635 0.781,2.844 0.344,0.208 10 false 6th 3.167,2.656 3.51,2.865 0.344,0.208 10 false 5th 1.156,2.667 1.5,2.875 0.344,0.208 10 false 5th 5.479,3.396 5.823,3.604 0.344,0.208 10 false 5th 4.729,2.667 5.073,2.875 0.344,0.208 10 false 5th 4.281,2.667 4.625,2.875 0.344,0.208 10 false 4th 4.74,3.396 5.083,3.604 0.344,0.208 10 false 4th 3.167,3.396 3.51,3.604 0.344,0.208 10 false 4th 1.604,2.677 1.948,2.885 0.344,0.208 10 false 4th 1.135,3.396 1.479,3.604 0.344,0.208 10 false 4th 0.448,3.396 0.792,3.604 0.344,0.208 10 false 5th 1.625,3.385 1.958,3.615 0.333,0.229 10 false 3rd 4.281,3.406 4.583,3.677 0.302,0.271 10 false 3rd 6,2.625 6.854,3.208 0.854,0.583 10 false Tow/Haul Control: Off 6,3.177 7,3.708 1,0.531 10 false Tow/Haul Control: On 1.99,3.396 2.313,3.646 0.323,0.25 10 false 2rd 2.344,2 3.365,2.271 1.021,0.271 10 false 2nd ←→ 3rd





c.

Driver's Intention Support Control

i.

When a trailer is not being towed

·

Driver's intention support control estimates the driver's intention based on the accelerator operation and vehicle condition and selects a shift pattern that is well-suited to each driver.



ii.

When a trailer is being towed

·

During tow/haul control operation, the driver's intention support control ensures drivability while towing a trailer by determining the driver'intention based on accelerator pedal operation and vehicle condition and performs the controls shown in the chart.


Control Operation Available for
Sudden Accelerator Pedal Depress Control When the driver operates (presses) the accelerator pedal quickly, this control causes the transmission to downshift rapidly to improve acceleration response. 4th to 6th
Sudden Accelerator Pedal Release Control When the driver releases the accelerator quickly, this control makes it easy for the transmission to hold the gear, which improves engine braking force and re-acceleration response. 3rd to 6th
Sudden Deceleration Downshift Control When the driver decelerates the vehicle suddenly, this control downshifts rapidly, which improves engine braking force and re-acceleration response. 3rd to 6th




MULTI-MODE AUTOMATIC TRANSMISSION


a.

General

i.

A multi-mode automatic transmission is designed to allow the driver to switch the gear ranges (a multi-mode transmission is not for manually selecting single gears). After shifting the shift lever to the S mode position and moving the shift lever to the "+" position or to the "-" position, the driver can select the desired shift range. Thus, the driver is able to shift gears with a manual-like feel.

System Diagram
X128202E03
1.021,0.563 2.198,0.885 1.177,0.323 10 false Combination Meter 0.927,0.979 2.302,1.292 1.375,0.313 10 false S Mode Indicator Light 0.781,1.385 2.531,1.677 1.75,0.292 10 false Shift Range Indicator Light 3.771,0.698 5.542,1.052 1.771,0.354 10 false Transmission Control Switch 3.302,2.677 3.646,3 0.344,0.323 10 false ECM 3.115,1.438 4.042,2.146 0.927,0.708 10 false Shift-up Signal ("+") 4.208,1.427 5.292,2.115 1.083,0.688 10 false Shift-down Signal ("-") 5.344,1.427 6.26,1.771 0.917,0.344 10 false S Mode Signal 1.74,2.052 2.885,2.406 1.146,0.354 10 false CAN (V Bus) 2.448,3.24 3.479,3.875 1.031,0.635 10 false Ignition Advance Control 3.885,3.094 4.542,4.521 0.656,1.427 10 false Fluid Pressure Control Signals 4.719,3.271 5.688,3.927 0.969,0.656 10 false Solenoid Valve Control Signals 4.177,4.792 4.469,5.063 0.292,0.271 10 false A/T 2.375,4.521 2.865,4.875 0.49,0.354 10 false Engine



b.

Operation

i.

Column Shift Lever

·

The driver selects the S mode position by engaging the shift lever. At this time, the 4th or 5th range is selected according to the vehicle speed. (When the driver selects the S mode during AI-SHIFT control, the current gear will be selected as the shift range.) Then, the shift range positions change one at a time, as the driver moves the transmission control switch to the up ("+" position) or to the down ("-" position).

·

Under this control, the ECM effects optimal shift control within the usable gear range that the driver has selected. As with an ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.

·

Holding the transmission control switch in the "+" position with the shift lever in the S mode position will change the shift range to the 6th range regardless of range position (1st to 5th).

·

When the shift lever is in the S mode position, the S mode indicator light in the combination meter illuminates. The shift range indicator light indicates the state of the shift range position that the driver has selected.

X131638E01
4.885,3.271 4.885,2.844 true 5.667,2.844 5.531,1.281 5.531,1.281 5.74,1.281 true 0.875,1.365 2.083,2.031 1.208,0.667 10 false Transition of Shift Range Positions 0.969,5.26 2.656,5.76 1.688,0.5 10 false : Default Shift Range 3.188,3.021 4.26,3.698 1.073,0.677 10 false S Mode Position 4.594,3.302 5.406,3.854 0.813,0.552 10 false Shift Lever 4.573,4.24 5.635,4.531 1.063,0.292 10 false Shift Pattern 5.813,1.208 6.74,2.167 0.927,0.958 10 false Transmission Control Switch

Usable Gear Chart
Shift Range Shift Range Indicator Light Indication Usable Gears
6th 6 6th←→5th←→4th←→3rd←→2nd←→1st
5th 5 5th←→4th←→3rd←→2nd←→1st
4th 4 4th←→3rd←→2nd←→1st
3rd 3 3rd←→2nd←→1st
2nd 2 2nd←→1st
1st 1 1st



ii.

Floor Shift Lever

·

The driver selects the S mode position by engaging the shift lever. At this time, the 4th or 5th range is selected according to the vehicle speed. (When the driver selects the S mode during AI-SHIFT control, the current gear will be selected as the shift range.) Then, the shift range positions change one at a time, as the driver moves the shift lever to the front ("+" position) or to the rear ("-" position).

·

Under this control, the ECM effects optimal shift control within the usable gear range that the driver has selected. As with an ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.

·

Holding the transmission control switch in the "+" position with the shift lever in the S mode position will change the shift range to the 6th range regardless of range position (1st to 5th).

·

When the shift lever is in the S mode position, the S mode indicator light in the combination meter illuminates. The shift range indicator light indicates the state of the shift range position that the driver has selected.

X128203E01
0.51,2.417 1.615,3.052 1.104,0.635 10 false Transition of Shift Range Position 0.469,4.26 1.615,4.719 1.146,0.458 9 false : Default shift range 3.656,1.188 4.719,1.51 1.063,0.323 10 false S Mode Position 4.5,2.979 5.313,3.323 0.813,0.344 10 false Shift Pattern

Usable Gear Chart
Shift Range Shift Range Indicator Light Indication Usable Gears
6th 6 6th←→5th←→4th←→3rd←→2nd←→1st
5th 5 5th←→4th←→3rd←→2nd←→1st
4th 4 4th←→3rd←→2nd←→1st
3rd 3 3rd←→2nd←→1st
2nd 2 2nd←→1st
1st 1 1st





DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the MIL (Malfunction Indicator Lamp) in the combination meter illuminates or blinks to inform the driver.


b.

The ECM will also store the DTCs (Diagnostic Trouble Codes) of the malfunctions. The DTCs can be accessed using the Techstream.


c.

For details, refer to the Repair Manual.



FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or solenoid.

Fail-Safe Control List
Malfunction Part Function
Input Speed Sensor (NT) When the input speed sensor malfunctions, shift control is effected using the information from the output speed sensor signal (SP2).
During an input speed sensor malfunction, up-shift to the 5th, 6th, AI-SHIFT and flex lock-up clutch control are prohibited.
Output Speed Sensor (SP2) When the output speed sensor malfunctions, shift control is effected using the information from the input speed sensor signal (NT).
When the output speed sensor malfunctions, up-shift to the 5th, 6th, AI-SHIFT and flex lock-up clutch control are prohibited.
ATF Temperature Sensor No.1 (THO1) When the ATF temperature sensor No1 malfunctions, up-shift to the 5th, 6th and flex lock-up clutch control are prohibited.
Solenoid Valve S1, S2, S3, S4 and SR When a solenoid valve listed at left fails, the current to the failed solenoid valve is cut off.
Shift control is changed to a fail-safe mode to shift gears using the normal solenoid valves to allow continued driving. Refer to the table on the next page for an operation example.
Solenoid Valve SL1 and SL2 During a solenoid valve SL1 or SL2 malfunction, up-shift to the 5th and 6th and flex lock-up clutch control are prohibited.
Solenoid Valve SLU During a solenoid valve SLU malfunction, the current to the solenoid valve is stopped. Because this stops lock-up control and flex lock-up control, fuel economy decreases.
Solenoid Valve SLT During a solenoid valve SLT malfunction, the current to the solenoid valve is stopped. Because this stops line pressure optimal control, the shift shock increases. However, shifting is effected through normal clutch pressure control.

Shift Position or Shift Range Solenoid Valve Gear
S1 S2 S3 S4 SR SL1 SL2
D, S6 Off On On Off On Off On 1st
On On On Off On Off On 2nd
On Off On Off On Off On 3rd
On Off Off Off On Off On 4th
On Off Off On Off On Off 5th
On On Off On Off On Off 6th
S5 Off On On Off On Off On 1st
On On On Off On Off On 2nd
On Off On Off On Off On 3rd
On Off Off Off On Off On 4th
On Off Off On Off On Off 5th
S4 Off On On Off On Off On 1st
On On On Off On Off On 2nd
On Off On Off On Off On 3rd
On Off Off Off On Off On 4th
S3 Off On On Off On Off On 1st
On On On Off On Off On 2nd
On Off On Off On Off Off 3rd
S2 Off On On Off On Off On 1st
On On On On On Off Off 2nd
S1 Off On On Off On Off Off 1st

Example
Shift Position or Shift Range Solenoid Valve Gear
S1 S2 S3 S4 SR SL1 SL2

E/B: Engine braking

D, S6 X On On Off On Off On 1st
X On → Off On → Off Off On Off On 1st → 4th
X Off On → Off Off On Off On 3rd → 4th
X Off Off Off On Off On 4th
X Off Off On Off On Off 5th
X On → Off Off On Off On Off N → 5th
S5 X On On Off On Off On 1st
X On → Off On → Off Off On Off On 1st → 4th
X Off On → Off Off On Off On 3rd → 4th
X Off Off Off On Off On 4th
X On → Off Off On Off On Off 5th
S4 X On On Off On Off On 1st
X On → Off On → Off Off On Off On 1st → 4th
X Off On → Off Off On Off On 3rd → 4th
X Off Off Off On Off On 4th
S3 X On On Off On Off On 1st
X On → Off On → Off Off On Off On 1st → 4th
X Off On → Off Off On Off Off → On 3rd (E/B) → 4th
S2 X On On Off On Off On 1st
X On → Off On → Off On On → Off Off Off → On 1st (E/B) →2nd
S1 X On On Off On Off Off 1st (E/B)