General
The power tilt and power telescopic system consists of the Tilt & Telescopic ECU, tilt and telescopic manual switch, tilt motor, and telescopic motor.
The Tilt & Telescopic ECU controls this system.
System Diagram
Layout of Main Components
| *1 | Main Body ECU (Driver Side Junction Block) | *2 | Mirror ECU |
| *3 | Memory Switch | *4 | Combination Switch
·
Tilt and Telescopic Manual Switch |
| *5 | Driver Seat ECU | *6 | DLC3 |
| *7 | Tilt and Telescopic ECU | - | - |
| *1 | Tilt and Telescopic ECU | *2 | Telescopic Motor
·
Motor ·
Position Sensor |
| *3 | Tilt Motor
·
Motor ·
Position Sensor |
- | - |
| *a | Top View | *b | Bottom View |
System Control
General
This system has the following control functions, thus providing excellent ease of operation and entry/exit.
| Control | Outline | |
|---|---|---|
| Manual | The tilt and telescopic positions can be adjusted using the tilt and telescopic manual switch. | |
| Automatic | Auto Away | The steering wheel automatically tilts up and retracts all the way when the ignition switch is changed from ACC or IG ON to OFF. |
| Auto Return | When the ignition switch is changed from OFF to ACC or IG ON, the steering wheel automatically returns to the previous position which was set before the ignition switch was turned off. | |
| Memory | 2 steering wheel positions can be memorized, allowing different positions to be restored by the memory system. | |
| Fail-Safe | When the tilt and telescopic ECU detects a malfunction in the power tilt and telescopic system, the ECU switches to a fail-safe mode. | |
| Diagnosis | When the tilt and telescopic ECU detects a malfunction in the power tilt and telescopic system, the ECU stores the malfunction data in memory. | |
Manual Control
A stepless tilt adjustment allows the steering wheel to be tilted 6° vertically, and the telescopic mechanism allows it to be moved in and out 40 mm (1.58 in.).
| *a | Tilt | *b | Telescopic |
| *c | 1.6° | *d | 4.4° |
| *e | 20.0 mm (0.79 in.) | *f | 20.0 mm (0.79 in.) |
Fail-safe
When the tilt and telescopic ECU detects a malfunction in the power tilt and telescopic system, the ECU changes the control mode to a fail-safe mode as follows:
| Detection Item | Fail-safe |
|---|---|
| Tilt Position Sensor or Tilt Motor Circuit Malfunction | Tilt operation is suspended. |
| Telescopic Position Sensor or Telescopic Motor Circuit Malfunction | Telescopic operation is suspended. |
| ECU Power Source Circuit Malfunction | Tilt and Telescopic operations are suspended. |
The table below shows operations that are possible even when there is a problem with communication among ECUs related to the tilt and telescopic ECU and the power tilt and telescopic system.
| Operation | ECU or Switch for which communication is lost | |||
|---|---|---|---|---|
| Main Body ECU (Ignition Signal) | Driver Seat ECU | Mirror ECU | Related ECU and Switch | |
| Manual | X* | ○ | ○ | X* |
| Automatic Away | X | ○ | ○ | X |
| Automatic Return | X* | ○ | ○ | X* |
| Memory | X | X | X | X |
| Recall | X* | X | X | X |
X: Not possible
○ : Possible
*: When the power (ignition switch signal) for the tilt and telescopic ECU is on, the operation is possible. When it is off, the operation is not possible.
Diagnosis
If the tilt and telescopic ECU detects a malfunction in the power tilt and telescopic system, the ECU stores the malfunction data in memory. Then, by connecting a Techstream to the DLC3 terminal, the Diagnostic Trouble Codes (DTCs) can be accessed and an active test can be performed to test the operation of the tilt motor and the telescopic motor. For details, refer to the Repair Manual.