Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0101  Mass Air Flow Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0102 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0102).

DTC Code DTC Detection Condition Trouble Area
P0101 Conditions (a), (b), (c), (d) and (e) continue for more than 10 seconds (2 trip detection logic):
(a) Engine running
(b) Engine coolant temperature 70°C (158°F) or higher
(c) Throttle Position (TP) sensor voltage 0.2 V or more and less than 3.6 V
(d) Average engine load value ratio less than 0.85, or more than 1.29 (varies with estimated engine load)
Average engine load value ratio = Average engine load based on MAF meter output / Average engine load estimated from driving conditions
(e) Average air-fuel ratio less than -15%, or more than 15%
·

Mass Air Flow (MAF) meter

·

Air induction system

·

PCV hose connections



MONITOR DESCRIPTION

The MAF meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and to provide an appropriate air-fuel ratio. Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The ECM monitors the average engine load value ratio to check the MAF meter for malfunctions. The average engine load value ratio is obtained by comparing the average engine load calculated from the MAF meter output to the average engine load estimated from the driving conditions, such as the engine speed and the throttle opening angle. If the average engine load value ratio is below the threshold value, the ECM determines that the intake air volume is low, and if the average engine load value ratio is above the threshold value, the ECM determines that the intake air volume is high.

If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY

Related DTCs P0101: Mass air flow meter rationality
Required Sensors/Components (Main) Mass air flow meter
Required Sensors/Components (Related) Crankshaft Position (CKP) sensor, Engine Coolant Temperature (ECT) sensor and Throttle Position (TP) sensor
Frequency of Operation Continuous
Duration 10 times
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Throttle position (TP sensor voltage) 0.2 V or more and less than 3.6 V
Time after engine start 5 seconds or more
Battery voltage 10.5 V or more
Engine coolant temperature 70°C (158°F) or more
Estimated load 30 to 100%
MAF sensor circuit fail (P0102, P0103) Not detected
IAT sensor circuit fail (P0112, P0113) Not detected
ECT sensor circuit fail (P0115, P0117, P0118) Not detected
CKP sensor circuit fail (P0335, P0337, P0338) Not detected
TP sensor circuit fail (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135) Not detected
Canister pressure sensor circuit fail (P0452, P0453) Not detected
EVAP leak detection pump fail (P2401, P2402) Not detected
EVAP vent valve fail (P2419, P2420) Not detected

TYPICAL MALFUNCTION THRESHOLDS

Both of following conditions 1 and 2 met -
1. Averaged engine load value ratio Less than 0.85, or more than 1.29 (varies with estimated engine load)
2. Averaged air-fuel ratio Less than -15%, or more than 15%

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

A198820E01
0.596,0.357 1.520,0.531 0.924,0.174 10 Vehicle Speed 0.147,0.67 1.368,0.853 1.221,0.184 10 112 km/h (70 mph) 0.161,1.569 1.298,1.743 1.137,0.174 10 80 km/h (50 mph) 1.175,2.304 1.544,2.506 0.369,0.202 10 Idling 1.81,2.874 2.651,3.057 0.841,0.184 10 Warming Up 3.958,2.93 5.151,3.095 1.193,0.165 10 5 minutes or more 2.09,2.192 2.320,2.357 0.230,0.165 10 [A] 4.458,0.968 4.665,1.157 0.207,0.188 10 [B] 5.425,3.341 5.679,3.500 0.254,0.159 10 [C]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher [A].

8.

Drive the vehicle at approximately 80 km/h (50 mph) to 112 km/h (70 mph) for 5 minutes or more [B].

HINT:

Drive while keeping the engine load as stable as possible.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0101.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.



14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0101 is output A
P0101 and other DTCs are output B


HINT:

If any DTCs other than P0101 are output, troubleshoot those DTCs first.



A

2.CHECK AIR INDUCTION SYSTEM

B

2.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK PCV HOSE CONNECTIONS

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

3.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV hose is connected correctly and is not damaged.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG