Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM D

3UR-FE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

HINT:

If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.



A317524E15
0.375,1.125 2.063,1.323 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.458,0.177 3.042,0.365 0.583,0.188 10 false DTC set 0.406,2.781 2.792,2.979 2.385,0.198 10 false Freeze frame data which can be read

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, 5 separate sets of freeze frame data can be checked.

·

3 data sets before the DTC was set.

·

1 data set when the DTC was set.

·

1 data set after the DTC was set.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.




LIST OF FREEZE FRAME DATA


Tester Display Measurement Item Diagnostic Note
Vehicle Speed Vehicle speed Speed indicated on speedometer.
Engine Speed Engine speed -
Calculate Load Calculated load Calculated load by ECM.
Vehicle Load Vehicle load -
MAF Mass air flow volume If approximately 0.0 gm/sec:
·

Mass air flow meter power source circuit open or short.


·

VG circuit open or short.


If 160.0 gm/sec or more:
·

E2G circuit open.


Atmosphere Pressure Atmosphere pressure -
Coolant Temp Engine coolant temperature If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Intake Air Intake air temperature If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Engine Run Time Accumulated engine running time -
Initial Engine Coolant Temp Engine coolant temperature at engine start -
Initial Intake Air Temp Intake air temperature at engine start -
Battery Voltage Battery voltage -
Accel Sens. No.1 Volt % Absolute Accelerator Pedal Position (APP) No. 1 -
Accel Sens. No.2 Volt % Absolute APP No. 2 -
Throttle Sensor Volt % Throttle sensor positioning -
Throttl Sensor #2 Volt % Throttle sensor positioning #2 -
Throttle Sensor Position Throttle position -
Throttle Motor DUTY Throttle motor -
Throttle Position Throttle Position For use when engine stall, starting problems or rough idle is present.
ISC Flow Flow rate calculated using information from each sensor For use when engine stall, starting problems or rough idle is present.
ISC Position Requested opening amount calculated using ISC control For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value ISC feedback compensation amount For use when engine stall, starting problems or rough idle is present.
ISC Learning Value ISC learned compensation amount For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val Compensation flow rate according to electrical load For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val Compensation flow rate according to air conditioner load For use when engine stall, starting problems or rough idle is present.
PS Feedback Val Compensation flow rate according to power steering load For use when engine stall, starting problems or rough idle is present.
Low Revolution Control Low engine speed control operation state For use when engine stall, starting problems or rough idle is present.
Neutral Control Neutral control operation state For use when engine stall, starting problems or rough idle is present.
N Range Status Shift lever N status For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow Intake air compensation flow rate For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow Flow loss due to deposits For use when engine stall, starting problems or rough idle is present.
Fuel Pump Duty Fuel pump duty -
Injector (Port) Injection period of No. 1 cylinder -
Injection Volum (Cylinder 1) Injection volume -
Vacuum Pump Key-off EVAP system leak detection pump status Refer to EVAP System (See page (Click here)).
Current Fuel Type Status of the current fuel type -
EVAP (Purge) VSV EVAP purge VSV duty ratio -
Evap Purge Flow Ratio of evaporative purge flow to intake air volume -
Purge Density Learn Value Learning value of purge density -
EVAP System Vent Value Key-off EVAP system vent valve status -
EVAP Purge VSV EVAP Purge VSV -
Purge Cut VSV Duty Purge VSV duty -
Target Air-Fuel Ratio Ratio compared to stoichiometric level -
AF Lambda B1S1 Output air fuel ratio associated with Bank 1 Sensor 1 -
AF Lambda B2S1 Output air fuel ratio associated with Bank 2 Sensor 1 -
AFS Voltage B1S1 A/F sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Voltage B2S1 A/F sensor output voltage Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Current B1S1 A/F sensor current -
AFS Current B2S1 A/F sensor current -
A/F Heater Duty #1 A/F heater duty ratio (for Bank 1) -
A/F Heater Duty #2 A/F heater duty ratio (for Bank 2) -
O2S B1S2 Heated oxygen sensor output Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S B2S2 Heated oxygen sensor output Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S Impedance B1S2 Sub heated oxygen sensor impedance (for Sensor 2) -
O2S Impedance B2S2 Sub heated oxygen sensor impedance (for Sensor 2) -
O2 Heater B1S2 Heated oxygen sensor heater -
O2 Heater B2S2 Heated oxygen sensor heater -
O2 Heater Curr Val B1S2 Heated oxygen sensor current -
O2 Heater Curr Val B1S2 Heated oxygen sensor current -
Short FT #1 Short-term fuel trim Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #1 Long-term fuel trim Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #1 Air fuel ratio learn value area of idle (for Bank 1) -
A/F Learn Value Low #1 Air fuel ratio learn value area of low load (for Bank 1) -
A/F Learn Value Mid1 #1 Air fuel ratio learn value area of middle load 1 (for Bank 1) -
A/F Learn Value Mid2 #1 Air fuel ratio learn value area of middle load 2 (for Bank 1) -
A/F Learn Value High #1 Air fuel ratio learn value area of high load (for Bank 1) -
Total FT #1 Total fuel trim -
Short FT #2 Short-term fuel trim Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #2 Long-term fuel trim Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #2 Air fuel ratio learn value area of idle (for Bank 2) -
A/F Learn Value Low #2 Air fuel ratio learn value area of low load (for Bank 2) -
A/F Learn Value Mid1 #2 Air fuel ratio learn value area of middle load 1 (for Bank 2) -
A/F Learn Value Mid2 #2 Air fuel ratio learn value area of middle load 2 (for Bank 2) -
A/F Learn Value High #2 Air fuel ratio learn value area of high load (for Bank 2) -
Total FT #2 Total fuel trim -
Fuel System Status #1 Fuel system status (for Bank 1)
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop.

·

CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to detected system fault.

·

CLFault: Closed loop but heated oxygen sensor, which is used for fuel control, is malfunctioning.


Fuel System Status #2 Fuel system status (for Bank 2)
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop.

·

CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to detected system fault.

·

CLFault: Closed loop but heated oxygen sensor, which is used for fuel control, is malfunctioning.


Air pump pressure (Absolute) Air pump pressure -
Air Pump2 Pressure (Absolute) Air pump pressure (Bank 2) -
Air Pump Pulsation Pressure Air pump pulsation pressure -
Air Pump2 Pulsation Pressure Air pump pulsation pressure (Bank 2) -
Secondary Air Control VSV Secondary air injection system status -
2nd Air System Status Second air system status -
AI Test Secondary air injection system operation prohibit -
IGN Advance Ignition advance -
Subfreezing Conditions Subfreezing Conditions -
Air Pump Freeze Air Pump Freeze -
Air Switching Valve Freeze Air Switching Valve Freeze -
Air Switching Valve2 Freeze Air Switching Valve2 Freeze -
Air Pump Heater Air Pump Heater -
IGN Advance IGN Advance -
Knock Feedback Value Feedback value of knocking -
Knock Correct Learn Value Correction learning value of knocking -
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #7 Individual cylinder timing advance compensation amount (No. 7) For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #8 Individual cylinder timing advance compensation amount (No. 8) For use when engine stall, starting problems or rough idle is present.
ACIS VSV VSV for Acoustic Control Induction System (ACIS) -
Actual VVT Angle #1 Actual VVT angle (for Bank 1) -
Actual VVT Angle #2 Actual VVT angle (for Bank 2) -
Actual VVT Ex Angle #1 Actual exhaust VVT angle (for Bank 1) -
Actual VVT Ex Angle #2 Actual exhaust VVT angle (for Bank 2) -
VVT Control Status #1 VVT control status -
VVT Control Status #2 VVT control status -
Catalyst Temp B1S1 Estimated catalyst temperature (for Sensor 1) -
Catalyst Temp B2S1 Estimated catalyst temperature (for Sensor 1) -
Catalyst Temp B1S2 Estimated catalyst temperature (for Sensor 2) -
Catalyst Temp B2S2 Estimated catalyst temperature (for Sensor 2) -
Starter Signal Starter switch (STSW) signal -
Starter Control Starter switch status -
Power Steering Signal Power steering switch status -
Starter Relay Starter relay status -
ACC Relay ACC relay status -
Neutral Position SW Signal Park/Neutral position (PNP) switch signal -
Transfer L4 L4 status of the transfer -
Stop Light Switch Stop light switch -
A/C Signal A/C signal -
Closed Throttle Position SW Closed throttle position switch -
Fuel Cut Condition Fuel cut condition -
Immobiliser Communication Immobiliser communication -
TC Terminal TC terminal status -
Time after DTC Cleared Cumulative time after DTC cleared -
Distance from DTC Cleared Accumulated distance from DTC cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared -
Dist Batt Cable Disconnect Accumulated distance from battery cable disconnected -
IG OFF Elapsed Time Cumulative time after ignition switch off -
TC and TE1 TC and CG (TE1) terminals of DLC3 -
Ignition Trig. Count Ignition counter -
Cylinder #1 Misfire Count Misfire Count of Cylinder #1 -
Cylinder #2 Misfire Count Misfire Count of Cylinder #2 -
Cylinder #3 Misfire Count Misfire Count of Cylinder #3 -
Cylinder #4 Misfire Count Misfire Count of Cylinder #4 -
Cylinder #5 Misfire Count Misfire Count of Cylinder #5 -
Cylinder #6 Misfire Count Misfire Count of Cylinder #6 -
Cylinder #7 Misfire Count Misfire Count of Cylinder #7 -
Cylinder #8 Misfire Count Misfire Count of Cylinder #8 -
All Cylinders Misfire Count All cylinders misfire -
Multi Cylinders Misfire Count Multiple cylinder misfire -
Misfire RPM Engine speed when misfire occurred -
Misfire Load Engine load when misfire occurred -
Misfire Margin Misfire monitoring -
Catalyst OT MF F/C Catalyst over temperature misfire prevention F/C -
Cat OT MF F/C History Catalyst over temperature misfire prevention F/C history -
Cat OT MF F/C Cylinder#1 Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#2 Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#3 Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#4 Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#5 Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#6 Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#7 Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected) -
Cat OT MF F/C Cylinder#8 Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected) -
Engine Speed (Starter Off) Engine speed when starter off For use when engine stall, starting problems or rough idle is present.
Starter Count Number of times starter turned on after ignition switch turned to ON For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip Distance driven during previous trip Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time Time elapsed after engine started (interval between ignition switch ON and off) For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp Engine coolant temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp Intake air temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature Engine oil temperature (estimated temperature) For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C Ambient temperature for A/C For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp Ambient temperature during previous trip For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation History of hesitation during engine start For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start History of low engine speed after engine start For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed Minimum engine speed For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure Power steering pressure sensor -
ACT VSV A/C cut status for Active Test -
Brake Override System Brake Override System -
Idle Fuel Cut Fuel cut idle ON: when throttle valve fully closed and engine speed over 3500 rpm.
FC TAU Fuel cut during very light load Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
Immobiliser Fuel Cut Status of the immobiliser fuel cut -
Immobiliser Fuel Cut History Status of the immobiliser fuel cut history -
Vehicle Spec Signal 1 Status of the Vehicle Spec Judge Signal 1 -
Electrical Load Signal 1 Electrical load signal -
Electrical Load Signal 2 Electrical load signal -
Cruise Cancel Signal Status of the cruise cancel signal -
A/F Sensor Determination (worst value) #1 Worst judgment value of air fuel ratio sensor output for bank 1
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


A/F Sensor Determination (worst value) #2 Worst judgment value of air fuel ratio sensor output for bank 2
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #1 Worst value of average engine speed fluctuation (Cylinder 1)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #2 Worst value of average engine speed fluctuation (Cylinder 2)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #3 Worst value of average engine speed fluctuation (Cylinder 3)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #4 Worst value of average engine speed fluctuation (Cylinder 4)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #5 Worst value of average engine speed fluctuation (Cylinder 5)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #6 Worst value of average engine speed fluctuation (Cylinder 6)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #7 Worst value of average engine speed fluctuation (Cylinder 7)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


Engine Speed Fluctuation Avg (worst value) #8 Worst value of average engine speed fluctuation (Cylinder 8)
·

The worst value detected during monitoring is displayed.

·

The value is reset when DTCs are cleared.


SPD (NT) Input shaft speed Data is displayed in increments of 50 rpm.
SPD (SP2) Output shaft speed -