Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0418  Secondary Air Injection System Control "A" Circuit  P0419  Secondary Air Injection System Control "B" Circuit  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC Code DTC Detection Condition Trouble Area
P0418
P0419

After cold engine starts, all of following conditions met (2 trip detection logic):

1.

Secondary Air Injection (AIR) system not operating (air pump OFF, Air Switching Valve [ASV] OFF)

2.

Diagnostic signal from Air Injection Control Driver (AID) 20%

3.

Battery voltage 8 V or more



·

Open in air pump drive circuit

·

Air pump

·

AID

·

ECM


P0418
P0419

After cold engine starts, all of following conditions met (2 trip detection logic):

1.

Secondary Air Injection (AIR) system operating (air pump ON, Air Switching Valve [ASV] ON)

2.

Diagnostic signal from Air Injection Control Driver (AID) 20%

3.

Battery voltage 8 V or more



·

Short between air pump drive circuit and body ground

·

Air pump

·

AID

·

ECM



MONITOR DESCRIPTION

The Air Injection Control Driver (AID) detects open and short circuits according to the voltages of the air pump terminal (VP) and the Air Switching Valve (ASV) terminal (VV), and transmits diagnostic information as a signal to the ECM.

For a short time after cold engine starts, the ECM transmits command signals to the AID to drive the air pump and ASV.

The AID transmits an air pump malfunction signal to the ECM if either of the following conditions is met:

·

The voltage at the AID terminal relating to the air pump is low despite the AID receiving command signals from the ECM to drive the air pump.

·

The voltage at the AID terminal relating to the air pump is high despite the AID receiving no command signals from the ECM to drive the air pump.


The ECM sets the DTC based on diagnostic signals from the AID.

MONITOR STRATEGY

Related DTCs P0418: Secondary air injection system air pump circuit range check (Bank 1)
P0419: Secondary air injection system air pump circuit range check (Bank 2)
Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air pump
Frequency of Operation Once per drive cycle
Duration 3 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Case 1:
Monitor runs whenever following DTCs not present -
All of following conditions (a) and (b) met -
(a) Secondary air injection pump Operating
(b) Secondary air injection switching valve Operating
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

Case 2:
Monitor runs whenever following DTCs not present -
All of following conditions (a) and (b) met -
(a) Secondary air injection pump Not operating
(b) Secondary air injection switching valve Not operating
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Diagnostic signal duty ratio from air injection control driver 11% or more, and 29% or less

COMPONENT OPERATING RANGE

Diagnostic signal duty ratio from air injection control driver 70% or more, and 90% or less when secondary air injection system operating.
0% when secondary air injection system not operating.

CONFIRMATION DRIVING PATTERN

A199319E04
0.226,1.73 1.419,1.914 1.193,0.184 10 Ignition Switch ON 0.264,2.211 1.457,2.395 1.193,0.184 10 Ignition Switch off 2.744,1.851 2.955,2.098 0.211,0.246 10 [A] 6.166,2.901 6.369,3.103 0.202,0.202 10 [B] 4.294,2.561 5.469,2.745 1.174,0.184 10 2 minutes or more 1.006,1.209 1.447,1.428 0.441,0.218 10 Idling

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on [A].

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).

13.

Check pending DTCs [B].

OK:

No pending DTC is output.


14.

After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0418 or P0419.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR INJECTION CONTROL DRIVER, BODY GROUND)
a.

Disconnect the cable from the battery negative (-) terminal.


b.

Disconnect the cable from the battery positive (+) terminal.


c.

Disconnect the air pump connector.


d.

Disconnect the AID connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D89-2 (B) - D48-2 (VP) Always Below 1 Ω
D90-2 (+B) - D52-2 (VP2) Always Below 1 Ω
D48-1 (BATT) - Battery positive (+) terminal Always Below 1 Ω
D52-1 (BAT2) - Battery positive (+) terminal Always Below 1 Ω
D89-4 (E) - Body ground Always Below 1 Ω
D90-4 (GND) - Body ground Always Below 1 Ω
D89-2 (B) or D48-2 (VP) - Body ground Always 10 kΩ or higher
D90-2 (+B) or D52-2 (VP2) - Body ground Always 10 kΩ or higher
D48-1 (BATT) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher
D52-1 (BAT2) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher




OK

2.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT AIR PUMP ASSEMBLY
a.
A217481E07
0.177,0.167 1.073,0.354 0.896,0.188 12 false for Bank 1: 0.146,1.604 1.042,1.792 0.896,0.188 12 false for Bank 2:

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.


d.

Connect the Techstream to the DLC3.


e.

Turn the ignition switch to ON and turn the Techstream on.


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



h.

Measure the current while the air pump is on and off.

Standard Current:
Tester Operation Air Pump ASV Specified Condition
AIR PUMP: ON, ASV: OPEN ON OPEN 10 to 40 A
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 1 A


NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

NG

3.REPLACE AIR PUMP ASSEMBLY
3.REPLACE AIR PUMP ASSEMBLY
a.

Replace the air pump assembly (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR PUMP>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.


g.

Start the engine after the Techstream initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Check pending DTCs.


k.

Turn the ignition switch off.

OK:

No pending DTC is output.


NOTICE:
·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

END

NG