| DTC | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
|---|---|---|---|---|---|
| P0451 | Canister pressure sensor abnormal voltage fluctuation | Sensor output voltage fluctuates frequently within a certain time period. | ·
Canister pump module ·
Connector/wire harness (Canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
·
EVAP monitoring (ignition switch off) ·
Engine running |
2 trip |
| Canister pressure sensor constant voltage | Sensor output voltage does not vary in a certain time period. | ·
EVAP monitoring (ignition switch off) |
|||
| P0452 | Canister pressure sensor low input | EVAP pressure less than 42.11009 kPa-a for 0.5 seconds. | ·
Canister pump module ·
Connector/wire harness (Canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
·
Ignition switch ON ·
EVAP monitoring (ignition switch off) |
1 trip |
| P0453 | Canister pressure sensor high input | EVAP pressure more than 123.76147 kPa-a for 0.5 seconds. | ·
Canister pump module ·
Connector/wire harness (Canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
·
Ignition switch ON ·
EVAP monitoring (ignition switch off) |
1 trip |
The canister pressure sensor is built into the canister pump module.
The description can be found in the EVAP (Evaporative Emission) System (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>EVAP System).
DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant
If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC. Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC. (Both the malfunctions are detected by 2 trip detection logic.)
DTC P0452: Canister pressure sensor voltage low
If the canister pressure sensor output [pressure] is below 42.11009 kPa-a (315.86779 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
DTC P0453: Canister pressure sensor voltage high
If the canister pressure sensor output [pressure] is 123.76147 kPa-a (928.33489 mmHg-a) or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P0452 and P0453
Within 2 minutes: P0451 (sensor stuck) Less than 15 seconds: P0451 (sensor noise) |
| MIL Operation | Immediate: P0452 and P0453
2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Atmospheric pressure (absolute pressure) | 70 to 110 kPa-a (525 to 825 mmHg-a) |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 40°C (40 to 104°F) |
| Either of following conditions met | A or B |
| A. Engine condition | Running |
| B. Time after key off | 5 or 7 or 9.5 hours |
| Canister pressure sensor malfunction | Not detected |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 40°C (40 to 104°F) |
| Canister pressure sensor malfunction (P0452, P0453) | Not detected |
| Atmospheric pressure | 70 to 110 kPa-a (525 to 825 mmHg-a) [absolute pressure] |
| Time after key off | 5 or 7 or 9.5 hours |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 8 V or higher |
| Starter | OFF |
| Either of following conditions met | (a) or (b) |
| (a) Ignition switch | ON |
| (b) ECM | Wake up by soak timer |
| Frequency that EVAP pressure change 0.3 kPa-g (2.25 mmHg-g) or more | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure measurement | Less than 0.65 kPa (4.876 mmHg) |
| EVAP pressure | Less than 42.11009 kPa-a (315.86779 mmHg-a) |
| EVAP pressure | More than 123.76147 kPa-a (928.33489 mmHg-a) |
The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.
Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
Do not run the engine during this operation.
When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap.
The Techstream is required to conduct the following diagnostic troubleshooting procedure.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.
| Display
(DTC Output) |
Test Result | Suspected Trouble Area | Proceed to |
|---|---|---|---|
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 42.11009 kPa-a (315.86779 mmHg-a) | ·
Wire harness/connector (ECM - Canister pressure sensor) ·
Canister pressure sensor ·
Short in ECM circuit |
A |
| P0453 | More than 123.76147 kPa-a (928.33489 mmHg-a) | ·
Wire harness/connector (ECM - Canister pressure sensor) ·
Canister pressure sensor ·
Open in ECM circuit |
B |
A
B
C
Turn the ignition switch off.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| D74-121 (PPMP) - Body ground | Always | 10 Ω or less | ·
Wire harness/connector (ECM - Canister pressure sensor) ·
Short in canister pressure sensor circuit |
A |
| D74-121 (PPMP) - Body ground | Always | 10 kΩ or more | ·
Wire harness/connector (ECM - Canister pressure sensor) ·
Short in ECM circuit |
B |
A
B
Disconnect the R12 canister pump module connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| D74-121 (PPMP) - Body ground | Always | 10 kΩ or more | Short in canister pressure sensor circuit | A*1 |
| B*2 | ||||
| D74-121 (PPMP) - Body ground | Always | 10 Ω or less | Short in wire harness/connector (ECM - Canister pressure sensor) | C |
*1: for 100 L (26.4 US gal) Fuel Tank
*2: for 144 L (38 US gal) Fuel Tank
A
B
C
Disconnect the R12 canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R12-8 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R12-6 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| R12-7 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Test Result | Suspected Trouble Area | Proceed to |
|---|---|---|
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A*1 |
| B*2 | ||
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | C |
*1: for 100 L (26.4 US gal) Fuel Tank
*2: for 144 L (38 US gal) Fuel Tank
A
B
C
Replace the canister pump module (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>CANISTER>REMOVAL).
When replacing canister pump module, check the canister pump module interior, charcoal canister assembly interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in canister interior, replace charcoal canister assembly and canister pump module together (replace charcoal canister assembly).
Check for filter blockage in the canister assembly. If the charcoal filter inside the canister assembly is clogged, replace canister and canister pump module together (replace canister assembly).
Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.
NEXT
Replace the charcoal canister assembly (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>CANISTER>REMOVAL).
When replacing the charcoal canister assembly, check the canister pump module interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.
Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.
NEXT
If the exhaust tailpipe has been removed, go to the next step before reinstalling it.
NEXT
Replace the ECM (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>ECM>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Wait for at least 60 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
If no pending DTCs are displayed on the Techstream, the repair has been successfully completed.
NEXT