Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve Assembly (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E39
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 5.439,3.922 3.840,0.174 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in OCV (for intake side of bank 1) circuit
(1 trip detection logic)
·

Open or short in OCV (for intake side of bank 1) circuit

·

OCV (for intake side of bank 1)

·

ECM


P0020 Open or short in OCV (for intake side of bank 2) circuit
(1 trip detection logic)
·

Open or short in OCV (for intake side of bank 2) circuit

·

OCV (for intake side of bank 2)

·

ECM



HINT:

This DTC relates to the Camshaft Timing Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve assembly (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY

Related DTCs P0010: VVT OCV range check (Bank 1)
P0020: VVT OCV range check (Bank 2)
Required Sensors/Components (Main) Camshaft timing oil control valve assembly (for intake side)
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 1 second
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not stored None
All of following conditions met -
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

Case 1
One of following conditions met -
A. All of following conditions met -
Battery voltage 11 to 13 V
Target duty cycle Less than 70%
B. All of following conditions met -
Battery voltage 13 V or more
Target duty cycle Less than 80%

Case 2
Current cut status Not cut

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Output duty cycle 100% or more

Case 2
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

VVT OCV duty ratio 3 to 100%

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010 or P0020.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A162759E22
5.868,4.237 6.218,4.421 0.350,0.184 10 ECM 5.42,0.506 5.854,0.662 0.434,0.156 10 OC1+ 5.42,1.234 5.854,1.390 0.434,0.156 10 OC1- 5.42,2.481 5.854,2.637 0.434,0.156 10 OC2+ 5.42,3.21 5.854,3.366 0.434,0.156 10 OC2- 0.103,1.631 2.991,1.843 2.888,0.211 10 OCV (for Intake Side of Bank 1) 0.103,3.617 3.102,3.828 2.999,0.211 10 OCV (for Intake Side of Bank 2) 0.101,1.449 0.387,1.614 0.286,0.165 10 D75 0.101,3.448 0.387,3.613 0.286,0.165 10 D76 1.466,0.491 1.592,0.681 0.126,0.191 10 1 1.473,1.229 1.592,1.402 0.119,0.173 10 2 1.466,2.444 1.592,2.635 0.126,0.191 10 1 1.473,3.182 1.592,3.356 0.119,0.173 10 2 5.868,4.085 6.153,4.239 0.286,0.154 10 D74 5.17,3.194 5.344,3.350 0.174,0.156 10 51 5.17,2.456 5.344,2.612 0.174,0.156 10 52 5.17,1.223 5.344,1.379 0.174,0.156 10 57 5.17,0.485 5.344,0.641 0.174,0.156 10 58

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK DTC
a.

Clear DTC after recording the freeze frame data and DTC (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


b.

Turn the ignition switch off.


c.

Allow the engine to idle and check DTC.


d.

Check that P0010 or P0020 is not output.

OK:

P0010 or P0020 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)
a.

Inspect the camshaft timing oil control valve assembly (for intake side) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) - ECM)
a.

Disconnect the D75 or D76 camshaft timing oil control valve assembly connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D75-1 - D74-58 (OC1+) Always Below 1 Ω
D76-1 - D74-52 (OC2+) Always Below 1 Ω
D75-2 - D74-57 (OC1-) Always Below 1 Ω
D76-2 - D74-51 (OC2-) Always Below 1 Ω
D75-1 or D74-58 (OC1+) - Body ground Always 10 kΩ or higher
D76-1 or D74-52 (OC2+) - Body ground Always 10 kΩ or higher
D75-2 or D74-57 (OC1-) - Body ground Always 10 kΩ or higher
D76-2 or D74-51 (OC2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR