Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM D

3UR-FBE ENGINE CONTROL  SFI SYSTEM  INITIALIZATION  


Inspection After Repair


Perform learning value reset and idle learning after replacing or servicing parts related to engine operation. Details on procedures required are indicated by an asterisk and a number, and are explained in detail following the table.

Part Replaced Engine Operation Learning Value Reset*1 Idle Learning*2
·

Throttle body assembly*3

·

Cleaning the deposits from the throttle body assembly*3


- ○ ○
Engine assembly - ○ ○
·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from air induction system

·

Gas leaks from exhaust system


Confirm the following:
Perform learning value reset and idle learning when one or more of the following conditions is met.
1.

A DTC was output before component replacement.

2.

An air fuel ratio learned value (one of A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1, A/F Learn Value High #1, A/F Learn Value Idle #2, A/F Learn Value Low #2, A/F Learn Value Mid1 #2, A/F Learn Value Mid2 #2 or A/F Learn Value High #2) displayed in the Data List was higher than +/-15% before component replacement.

3.

Starting failure, rough idle, or engine stalls after component replacement.


○ ○
The items in the list above do not apply. - -
Knock sensor*4 - - -

○: Necessary.

-: Unnecessary.


NOTICE:

Engine learned values cannot be reset by disconnecting the battery negative (-) terminal or removing the EFI NO. 1 and ETCS fuses.


*1: Learning Value Reset

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Value Reset.

5.

Confirm the following conditions as instructed on the screen.

- Ignition switch ON

- Engine stopped

- Battery voltage is higher than 9 V


6.

After confirming, select "Next" and initialize the learned value.

HINT:

If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.


7.

After the completion of learned value initialization, confirm the air fuel ratio learned values (A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1, A/F Learn Value High #1, A/F Learn Value Idle #2, A/F Learn Value Low #2, A/F Learn Value Mid1 #2, A/F Learn Value Mid2 #2 and A/F Learn Value High #2) in the Data List.

Result:

If 0 is displayed for all the air fuel ratio learned values, initialization has completed correctly.

If a value other than 0 is displayed for one of the air fuel ratio learned values, perform initialization again. After initialization, confirm the air fuel ratio learned values. If a value other than 0 is displayed, replace the ECM.



*2: Idle Learning

1.

Turn the ignition switch off and wait for at least 30 seconds.

2.

Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.

HINT:

Learning starts when the engine coolant temperature is 80°C (176°F) or higher.


3.

After the engine is warmed up, allow it to idle for 5 minutes with the air conditioning and all accessories off.

4.

Confirm that the idle speed is within the standard range.

Standard:
Engine Idle Speed
650 to 750 rpm: Idling


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




*3: Perform memory reset and idle learning after replacing the throttle body assembly or cleaning deposits from the throttle body assembly.

After that, check the idle speed. If the value is out of the specified range, perform the procedure below.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

History information for driving and stopping is necessary to update idle learning.


A250733E24
0.552,0.771 1.094,1.135 0.542,0.365 10 false 10 km/h 0.719,1.75 1.104,1.948 0.385,0.198 10 false Idling 0.167,2.177 1.083,2.542 0.917,0.365 10 false Ignition Switch ON 2.49,1.646 2.729,1.844 0.24,0.198 10 false [A] 3.198,0.542 3.438,0.74 0.24,0.198 10 false [B] 6.438,3.25 6.677,3.448 0.24,0.198 10 false [E] 4.781,3.26 5.021,3.458 0.24,0.198 10 false [D] 3.208,3 3.948,3.667 0.74,0.667 10 false 20 seconds or more 4.042,3 4.792,3.667 0.75,0.667 10 false 20 seconds or more 5.729,3 6.469,3.667 0.74,0.667 10 false 20 seconds or more 4.115,0.542 4.354,0.74 0.24,0.198 10 false [B] 5.781,0.542 6.021,0.74 0.24,0.198 10 false [B] 3.667,1.646 3.906,1.844 0.24,0.198 10 false [C] 4.583,1.656 4.823,1.854 0.24,0.198 10 false [C] 6.25,1.656 6.49,1.854 0.24,0.198 10 false [C]

1.

Warm up the engine (engine coolant temperature is 80°C (176°F) or higher, air conditioning and all accessories are off) [A].

2.

Drive the vehicle at 10 km/h (6 mph) or more [B].

3.

Idle the engine for 20 seconds or more [C].

4.

Repeat procedure [B] and [C], and check that the idle speed is within the specified range [D].

Standard:
Engine Idle Speed
650 to 750 rpm: Idling


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.

·

If the idle speed is still out of the specified range, repeat procedure [B] and [C] until the idle speed is within the specified range [E].




*4: Drive the vehicle for a short while after replacing the knock control sensor, and check if knocking occurs. If knocking occurs, drive the vehicle until knocking stops.



Fuel Density Learning Value Reset


NOTICE:

Performing "Fuel Density Learning Value Reset" initializes the alcohol concentration learned value. If learning of the alcohol concentration is not performed after performing initialization, DTCs may be stored. Do not perform initialization unless specified in the repair manual.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.


e.

After the completion of learned value initialization, confirm the air fuel ratio learned values (A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1, A/F Learn Value High #1, A/F Learn Value Idle #2, A/F Learn Value Low #2, A/F Learn Value Mid1 #2, A/F Learn Value Mid2 #2 or A/F Learn Value High #2) in the Data List.


f.

Confirm the following conditions as instructed on the screen.

i.

Ignition switch: ON


ii.

Engine: stopped


iii.

Battery voltage: 9 V or higher



g.

After confirming, select "Next" and initialize the learned value.

HINT:

If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.


Result:

If 0 is displayed for all the air fuel ratio learned values, initialization has completed correctly. If a value other than 0 is displayed for one of the air fuel ratio learned values, perform initialization again.



h.

Turn the ignition switch off and wait for at least 30 seconds.


i.

Turn the ignition switch to ON.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.

HINT:
·

After clearing the learned value, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

·

If "Fuel Density Learning Value Reset" is performed after warming the engine coolant up to approximately 50°C (122°F), the engine becomes easier to start afterward.




k.

Confirm the following conditions as instructed on the screen.

i.

Ignition switch: ON


ii.

Engine: stopped


iii.

Battery voltage: 9 V or higher



l.

Press "Next".

HINT:

When "Next" is pressed, initialization is performed automatically.



m.

Turn the ignition switch off.


n.

Add at least 8 liters (2 gallons) of fuel.

NOTICE:

Add fuel immediately after resetting. (Do not start the engine before adding fuel.)


HINT:
·

Learning of the alcohol concentration will not be started until the ECM judges that the fuel gauge has moved after resetting. Add at least 8 liters (2 gallons) of fuel.

·

Check "Fuel Remaining Volume" in the Data List and if it has a value of 85% or more, remove enough fuel so that the value decreases to less than 85% before adding fuel.




o.

Turn the ignition switch to ON and turn the Techstream on [A].

A199233E01
0.568,0.043 1.536,0.247 0.968,0.205 10 Vehicle Speed 1.247,1.962 1.653,2.139 0.406,0.177 10 Idling 0.442,2.249 1.709,2.405 1.268,0.156 10 Ignition Switch ON 2.009,2.339 2.210,2.540 0.201,0.201 10 [A] 2.529,1.836 2.734,2.013 0.205,0.177 10 [B] 3.324,1.839 3.548,2.011 0.224,0.171 10 [C] 4.797,0.442 5.026,0.615 0.229,0.173 10 [D] 5.622,3.29 5.846,3.461 0.224,0.171 10 [E] 0.414,0.317 1.625,0.480 1.211,0.163 10 120 km/h (75 mph) 0.44,1.198 1.652,1.361 1.211,0.163 10 60 km/h (38 mph) 4.343,2.922 5.541,3.099 1.198,0.177 10 5 minutes or more 2.13,2.992 2.925,3.169 0.795,0.177 10 Warming up 2.858,3.146 4.014,3.323 1.156,0.177 10 2 minutes or more 3.636,0.059 7.009,0.262 3.373,0.202 10 Engine coolant temperature is 75°C (167°F) or higher 3.062,2.043 3.463,0.148 3.463,0.148 3.585,0.148 false


p.

Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle / Alcohol Density Learning.


q.

Make sure that the Data List item "Alcohol Density Learning" is "Incmpl".


r.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].


s.

With the engine warmed up, idle the engine for 2 minutes or more [C].


t.

Drive the vehicle at a speed between 60 and 120 km/h (37 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



u.

Stop the vehicle [E].


v.

Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle / Alcohol Density Learning.


w.

Make sure that the Data List item "Alcohol Density Learning" is "Compl".

HINT:

If "Incmpl" is displayed, perform the confirmation driving pattern again.



x.

Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT #1, Short FT #2, Long FT #1 and Long FT #2.


y.

Check the data list values, and then write them down.


z.

Confirm the alcohol concentration in the fuel (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


aa.

Write down the alcohol concentration in the fuel.


ab.

Use the following formula to calculate the difference between the current learned value and the actual alcohol concentration in the fuel.

HINT:

[ (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) ] < 10%


Standard:
Result Specified Condition
Difference between actual alcohol concentration and Alcohol Density Estimate Less than 10%
Short FT #1, Short FT #2, Long FT #1 and Long FT #2 Between -35% and 35%


HINT:

If the result is not as specified, replace the fuel with E0 gasoline (approximately 20 liters (5 gallons)) to increase the concentration of gasoline. Then perform "Fuel Density Learning Value Reset" again.



ac.

Confirm that the idle speed is within the standard range.

Standard:
Engine Idle Speed
650 to 750 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




ad.

If the engine idle speed is not as specified, perform the following confirmation driving pattern.

A250733E38
0.021,0.771 1.083,0.979 1.063,0.208 10 false 10 km/h (6 mph) 0.708,1.75 1.094,1.948 0.385,0.198 10 false Idling 0.115,2.177 1.083,2.563 0.969,0.385 10 false Ignition Switch ON 2.49,1.667 2.729,1.865 0.24,0.198 10 false [A] 6.458,3.25 6.698,3.448 0.24,0.198 10 false [E] 4.76,3.25 5,3.448 0.24,0.198 10 false [D] 3.26,3.063 4,3.729 0.74,0.667 10 false 20 seconds or more 4.073,3.083 4.823,3.75 0.75,0.667 10 false 20 seconds or more 5.729,2.99 6.469,3.656 0.74,0.667 10 false 20 seconds or more 5.781,0.5 6.021,0.698 0.24,0.198 10 false [B] 3.198,0.5 3.438,0.698 0.24,0.198 10 false [B] 4.115,0.5 4.354,0.698 0.24,0.198 10 false [B] 6.219,1.667 6.458,1.865 0.24,0.198 10 false [C] 4.563,1.667 4.802,1.865 0.24,0.198 10 false [C] 3.646,1.667 3.885,1.865 0.24,0.198 10 false [C]

i.

Warm up the engine (engine coolant temperature is 80°C (176°F) or higher, air conditioning and all accessories are off) [A].


ii.

Drive the vehicle at 10 km/h (6 mph) or more [B].


iii.

Idle the engine for 20 seconds or more [C].


iv.

Repeat procedure [B] and [C], and check that the idle speed is within the specified range [D].

Standard:
Engine Idle Speed
650 to 750 rpm


HINT:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.

·

If the idle speed is still out of the specified range, repeat procedure [B] and [C] until the idle speed is within the specified range [E].