If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.
| DTC | Component | Fail-Safe Operation | Fail-Safe Deactivation Condition |
|---|---|---|---|
| P0011, P0015, P0021 and P0025 | Variable Valve Timing (VVT) System | ·
Idle up (control of combustion worsening) ·
Stopping fuel cut control |
Pass condition detected |
| P0031, P0032, P0051 and P0052 | Air-Fuel Ratio (A/F) Sensor Heater | ECM turns off A/F sensor heater. | Ignition switch off |
| P0037, P0038, P0057 and P0058 | Heated Oxygen (HO2) Sensor Heater | ECM turns off HO2 sensor heater. | Ignition switch off |
| P0102 and P0103 | Mass Air Flow (MAF) Meter | ECM calculates ignition timing according to engine speed and throttle valve position. | Pass condition detected |
| P0112 and P0113 | Intake Air Temperature (IAT) Sensor | ECM estimates IAT to be 20°C (68°F). | Pass condition detected |
| P0115, P0117 and P0118 | Engine Coolant Temperature (ECT) Sensor | ECM estimates ECT to be 80°C (176°F). | Pass condition detected |
| P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135 | Electronic Throttle Control System (ETCS) | ECM cuts off throttle actuator current and throttle valve returned to 7° throttle position by return spring.
ECM then adjusts engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with accelerator pedal opening angle to allow vehicle to continue at minimal speed*1. |
Pass condition detected and then ignition switch turned off |
| P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308*2 | ·
Fuel injector ·
Electronic Throttle Control System (ETCS) |
When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.
Under a low load and at a low engine speed: ·
Fuel cut is performed on the malfunctioning cylinder. 2.
Under a high load and at a high engine speed: ·
Throttle valve opening angle control is performed. ·
Fuel cut is performed on all cylinders or the malfunctioning cylinder. |
Pass condition detected and then ignition switch turned off |
| P0327, P0328, P032C, P032D, P0332, P0333, P033C and P033D | Knock Sensor | ECM sets ignition timing to maximum retard. | Ignition switch off |
| P0351 to P0358 | Ignition Coil | ECM cuts fuel. | Pass condition detected |
| P0504 | Stop Light Switch | The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. | Pass condition detected |
| P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 | Accelerator Pedal Position (APP) Sensor | The accelerator pedal position sensor has 2 sensor circuits:
Main and Sub. If either circuit malfunctions, the ECM limits the engine output. If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. |
Pass condition detected and then ignition switch turned off |
| P2432, P2433, P2437 and P2438 | Secondary Air Injection System | Throttle valve opening angle control is performed | Pass condition detected |
| P2440 and P2442 | Secondary Air Injection System | Throttle valve opening angle control is performed | Pass condition detected |
| P2445 and P2447 | Secondary Air Injection System | Throttle valve opening angle control is performed | Pass condition detected |
*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.