| Vehicle Speed
|
Vehicle speed
|
Speed indicated on speedometer.
|
| Engine Speed
|
Engine speed
|
-
|
| Calculate Load
|
Calculated load
|
Calculated load by ECM.
|
| Vehicle Load
|
Vehicle load
|
-
|
| MAF
|
Mass air flow volume
|
If approximately 0.0 gm/sec.:
·
Mass air flow meter power source circuit open or short.
·
VG circuit open or short.
If 160.0 gm/sec. or more:
|
| Atmosphere Pressure
|
Atmosphere pressure
|
-
|
| Coolant Temp
|
Engine coolant temperature
|
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
|
| Intake Air
|
Intake air temperature
|
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
|
| Engine Run Time
|
Accumulated engine running time
|
-
|
| Initial Engine Coolant Temp
|
Engine coolant temperature at engine start
|
-
|
| Coolant Temp Variation after Engine Start
|
Coolant temp variation after engine start
|
-
|
| Initial Intake Air Temp
|
Intake air temperature at engine start
|
-
|
| Intake Air Temp Variation after Engine Start
|
Intake air temp variation after engine start
|
-
|
| Battery Voltage
|
Battery voltage
|
-
|
| Glow Indicator Supported
|
Status of glow indicator supported
|
-
|
| Glow Indicator
|
Glow indicator
|
-
|
| Accel Sens. No. 1 Volt %
|
Absolute Accelerator Pedal Position (APP) No. 1
|
-
|
| Accel Sens. No. 2 Volt %
|
Absolute APP No. 2
|
-
|
| Throttle Sensor Volt %
|
Throttle position
|
-
|
| Throttl Sensor #2 Volt %
|
Throttle sensor positioning #2
|
-
|
| Throttle Sensor Position
|
Throttle sensor positioning
|
-
|
| Throttle Motor DUTY
|
Throttle actuator
|
-
|
| Throttle Position
|
Throttle position
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Flow
|
Flow rate calculated using information from each sensor
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Position
|
Requested opening amount calculated using ISC control
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Feedback Value
|
ISC feedback compensation amount
|
For use when engine stall, starting problems or rough idle is present.
|
| ISC Learning Value
|
ISC learned compensation amount
|
For use when engine stall, starting problems or rough idle is present.
|
| Electric Load Feedback Val
|
Compensation flow rate according to electrical load
|
For use when engine stall, starting problems or rough idle is present.
|
| Air Conditioner FB Val
|
Compensation flow rate according to air conditioner load
|
For use when engine stall, starting problems or rough idle is present.
|
| PS Feedback Val
|
Compensation flow rate according to power steering load
|
For use when engine stall, starting problems or rough idle is present.
|
| Low Revolution Control
|
Low engine speed control operation state
|
For use when engine stall, starting problems or rough idle is present.
|
| N Range Status
|
Shift lever N status
|
For use when engine stall, starting problems or rough idle is present.
|
| Eng Stall Control FB Flow
|
Intake air compensation flow rate
|
For use when engine stall, starting problems or rough idle is present.
|
| Deposit Loss Flow
|
Flow loss due to deposits
|
For use when engine stall, starting problems or rough idle is present.
|
| Fuel Press Switching Valve
|
Fuel pressure switching valve status
|
-
|
| Injector (Port)
|
Injection period of No. 1 cylinder
|
-
|
| Injection Volum (Cylinder 1)
|
Injection volume
|
-
|
| Fuel Pump/Speed Status
|
Fuel pump speed status
|
-
|
| Vacuum Pump
|
Key-off EVAP system leak detection pump status
|
Refer to EVAP System (See page ( )).
|
| EVAP (Purge) VSV
|
EVAP purge VSV duty ratio
|
-
|
| Evap Purge Flow
|
Ratio of evaporative purge flow to intake air volume
|
-
|
| Purge Density Learn Value
|
Learning value of purge density
|
-
|
| EVAP System Vent Valve
|
Key-off EVAP system vent valve status
|
-
|
| EVAP Purge VSV
|
EVAP Purge VSV
|
-
|
| Purge Cut VSV Duty
|
Purge cut VSV duty
|
-
|
| Target Air-Fuel Ratio
|
Ratio compared to stoichiometric level
|
-
|
| AF Lambda B1S1
|
Output air fuel ratio associated with Bank 1 Sensor 1
|
-
|
| AF Lambda B2S1
|
Output air fuel ratio associated with Bank 2 Sensor 1
|
-
|
| AFS Voltage B1S1
|
A/F sensor output voltage
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
|
| AFS Voltage B2S1
|
| AFS Current B1S1
|
A/F sensor current (for Bank 1)
|
-
|
| AFS Current B2S1
|
A/F sensor current (for Bank 2)
|
-
|
| A/F Heater Duty B1S1
|
A/F heater duty ratio (for Bank 1)
|
-
|
| A/F Heater Duty B2S1
|
A/F heater duty ratio (for Bank 2)
|
-
|
| O2S B1S2
|
Heated oxygen sensor output
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
|
| O2S B2S2
|
| O2S Impedance B1S2
|
Sub heated oxygen sensor impedance (for Sensor 2)
|
-
|
| O2S Impedance B2S2
|
| O2 Heater B1S2
|
Heated oxygen sensor heater (for Sensor 2)
|
-
|
| O2 Heater B2S2
|
| O2 Heater Curr Val B1S2
|
Heated oxygen sensor current (for Sensor 2)
|
-
|
| O2 Heater Curr Val B2S2
|
| Short FT #1
|
Short-term fuel trim
|
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
|
| Long FT #1
|
Long-term fuel trim
|
Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
|
| A/F Learn Value Idle #1
|
Air fuel ratio learned value for idling (for Bank 1)
|
-
|
| A/F Learn Value Low #1
|
Air fuel ratio learned value for low engine loads (for Bank 1)
|
-
|
| A/F Learn Value Mid1 #1
|
Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)
|
-
|
| A/F Learn Value Mid2 #1
|
Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)
|
-
|
| A/F Learn Value High #1
|
Air fuel ratio learned value for high engine loads (for Bank 1)
|
-
|
| Total FT #1
|
Total fuel trim
|
-
|
| Short FT #2
|
Short-term fuel trim
|
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
|
| Long FT #2
|
Long-term fuel trim
|
Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
|
| A/F Learn Value Idle #2
|
Air fuel ratio learned value for idling (for Bank 2)
|
-
|
| A/F Learn Value Low #2
|
Air fuel ratio learned value for low engine loads (for Bank 2)
|
-
|
| A/F Learn Value Mid1 #2
|
Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)
|
-
|
| A/F Learn Value Mid2 #2
|
Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)
|
-
|
| A/F Learn Value High #2
|
Air fuel ratio learned value for high engine loads (for Bank 2)
|
-
|
| Total FT #2
|
Total fuel trim
|
-
|
| Fuel System Status #1
|
Fuel system status (for Bank 1)
|
·
OL (Open Loop): Has not yet satisfied conditions to go closed loop.
·
CL (Closed Loop): Using A/F sensor as feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to detected system fault.
·
CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
|
| Fuel System Status #2
|
Fuel system status (for Bank 2)
|
·
OL (Open Loop): Has not yet satisfied conditions to go closed loop.
·
CL (Closed Loop): Using A/F sensor as feedback for fuel control.
·
OL Drive: Open loop due to driving conditions (fuel enrichment).
·
OL Fault: Open loop due to detected system fault.
·
CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
|
| Air Pump Pressure (Absolute)
|
Air pump pressure (for Bank 1)
|
-
|
| Air Pump2 Pressure (Absolute)
|
Air pump pressure (for Bank 2)
|
-
|
| Air Pump Pulsation Pressure
|
Air pump pulsation pressure (for Bank 1)
|
-
|
| Air Pump2 Pulsation Pressure
|
Air pump pulsation pressure (for Bank 2)
|
-
|
| Secondary Air Control VSV
|
Secondary air switching valve status
|
-
|
| 2nd Air System Status
|
Secondary air injection system status
|
-
|
| AI Test
|
Secondary air injection system operation prohibit
|
-
|
| Subfreezing Conditions
|
Subfreezing conditions status
|
-
|
| Air Pump Freeze
|
Air pump freeze status
|
-
|
| Air Pump2 Freeze
|
Air pump 2 freeze status
|
-
|
| Air Switching Valve Freeze
|
Air switching valve freeze status
|
-
|
| Air Switching Valve2 Freeze
|
Air switching valve 2 freeze status
|
-
|
| Air Pump Heater
|
Air pump heater status
|
-
|
| IGN Advance
|
Ignition advance
|
-
|
| Knock Feedback Value
|
Feedback value of knocking
|
-
|
| Knock Correct Learn Value
|
Correction learning value of knocking
|
-
|
| Idle Spark Advn Ctrl #1
|
Individual cylinder timing advance compensation amount (No. 1)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #2
|
Individual cylinder timing advance compensation amount (No. 2)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #3
|
Individual cylinder timing advance compensation amount (No. 3)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #4
|
Individual cylinder timing advance compensation amount (No. 4)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #5
|
Individual cylinder timing advance compensation amount (No. 5)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #6
|
Individual cylinder timing advance compensation amount (No. 6)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #7
|
Individual cylinder timing advance compensation amount (No. 7)
|
For use when engine stall, starting problems or rough idle is present.
|
| Idle Spark Advn Ctrl #8
|
Individual cylinder timing advance compensation amount (No. 8)
|
For use when engine stall, starting problems or rough idle is present.
|
| ACIS VSV
|
VSV for Acoustic Control Induction System (ACIS)
|
-
|
| Actual VVT Angle #1
|
Actual VVT displacement angle (bank 1)
|
This item is used for freeze frame data only
|
| Actual VVT Angle #2
|
Actual VVT displacement angle (bank 2)
|
This item is used for freeze frame data only
|
| Actual VVT Ex Angle #1
|
Actual VVT exhaust displacement angle (bank 1)
|
This item is used for freeze frame data only
|
| Actual VVT Ex Angle #2
|
Actual VVT exhaust displacement angle (bank 2)
|
This item is used for freeze frame data only
|
| VVT Control Status #1
|
VVT control status (for Bank 1)
|
-
|
| VVT Control Status #2
|
VVT control status (for Bank 2)
|
-
|
| VVT Advance Fail
|
VVT control failure status
|
-
|
| Catalyst Temp B1S1
|
Estimated catalyst temperature (for Sensor 1)
|
-
|
| Catalyst Temp B2S1
|
| Catalyst Temp B1S2
|
Estimated catalyst temperature (for Sensor 2)
|
-
|
| Catalyst Temp B2S2
|
| Starter Signal
|
Starter signal
|
-
|
| Starter Control
|
Starter status
|
-
|
| Power Steering Signal
|
Power steering status
|
-
|
| Starter Relay
|
ST relay status
|
-
|
| ACC Relay
|
ACC relay status
|
-
|
| Neutral Position SW Signal
|
Park/Neutral position (PNP) switch signal
|
-
|
| Transfer L4
|
Park/Neutral position (PNP) switch signal
|
-
|
| Stop Light Switch
|
Stop light switch status
|
-
|
| A/C Signal
|
A/C signal status
|
-
|
| Closed Throttle Position SW
|
Closed throttle position switch
|
-
|
| Fuel Cut Condition
|
Fuel cut condition
|
-
|
| Immobiliser Communication
|
Immobiliser communication
|
-
|
| TC Terminal
|
TC terminal status
|
-
|
| Time after DTC Cleared
|
Cumulative time after DTC cleared
|
-
|
| Distance from DTC Cleared
|
Accumulated distance from DTC cleared
|
-
|
| Warmup Cycle Cleared DTC
|
Warm-up cycle after DTC cleared
|
-
|
| Dist Batt Cable Disconnect
|
Total distance vehicle driven after battery cable disconnected
|
-
|
| IG OFF Elapsed Time
|
Cumulative time after ignition switch off
|
-
|
| TC and TE1
|
TC and CG (TE1) terminals of DLC3
|
-
|
| Total Distance Traveled
|
Total distance traveled
|
-
|
| Ignition Trig. Count
|
Ignition counter
|
-
|
| Cylinder #1 Misfire Count
|
Cylinder #1 misfire count
|
-
|
| Cylinder #2 Misfire Count
|
Cylinder #2 misfire count
|
-
|
| Cylinder #3 Misfire Count
|
Cylinder #3 misfire count
|
-
|
| Cylinder #4 Misfire Count
|
Cylinder #4 misfire count
|
-
|
| Cylinder #5 Misfire Count
|
Cylinder #5 misfire count
|
-
|
| Cylinder #6 Misfire Count
|
Cylinder #6 misfire count
|
-
|
| Cylinder #7 Misfire Count
|
Cylinder #7 misfire count
|
-
|
| Cylinder #8 Misfire Count
|
Cylinder #8 misfire count
|
-
|
| All Cylinders Misfire Count
|
Misfire count of all cylinders
|
-
|
| Multi Cylinders Misfire Count
|
Multiple cylinder misfire count
|
-
|
| Misfire RPM
|
Engine speed when misfire occurred
|
-
|
| Misfire Load
|
Engine load when misfire occurred
|
-
|
| Misfire Margin
|
Margin to detect engine misfire
|
-
|
| Catalyst OT MF F/C
|
Catalyst over temperature misfire prevention F/C
|
-
|
| Cat OT MF F/C History
|
Catalyst over temperature misfire prevention F/C history
|
-
|
| Cat OT MF F/C Cylinder#1
|
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#2
|
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#3
|
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#4
|
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#5
|
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#6
|
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#7
|
Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Cat OT MF F/C Cylinder#8
|
Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)
|
-
|
| Engine Speed (Starter Off)
|
Engine speed when starter off
|
For use when engine stall, starting problems or rough idle is present.
|
| Starter Count
|
Number of times starter turned on after ignition switch turned to ON
|
For use when engine stall, starting problems or rough idle is present.
|
| Run Dist of Previous Trip
|
Distance driven during previous trip
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Starting Time
|
Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Coolant Temp
|
Engine coolant temperature during previous trip
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Intake Temp
|
Intake air temperature during previous trip
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Oil Temperature
|
Engine oil temperature (estimated temperature)
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Eng Oil Temp
|
Engine oil temperature during previous trip
|
For use when engine stall, starting problems or rough idle is present.
|
| Ambient Temp for A/C
|
Ambient temperature for A/C
|
For use when engine stall, starting problems or rough idle is present.
|
| Previous Trip Ambient Temp
|
Ambient temperature during previous trip
|
For use when engine stall, starting problems or rough idle is present.
|
| Engine Start Hesitation
|
History of hesitation during engine start
|
For use when engine stall, starting problems or rough idle is present.
|
| Low Rev for Eng Start
|
History of low engine speed after engine start
|
For use when engine stall, starting problems or rough idle is present.
|
| Minimum Engine Speed
|
Minimum engine speed
|
For use when engine stall, starting problems or rough idle is present.
|
| Power Steering Pressure
|
Power steering pressure sensor
|
-
|
| ACT VSV
|
A/C cut status for Active Test
|
-
|
| Brake Override System
|
Brake override system status
|
-
|
| Idle Fuel Cut
|
Fuel cut idle
|
ON: when throttle valve fully closed and engine speed over 3500 rpm.
|
| FC TAU
|
Fuel cut during very light load
|
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
|
| Immobiliser Fuel Cut
|
Status of the immobiliser fuel cut
|
-
|
| Immobiliser Fuel Cut History
|
Immobiliser fuel cut history
|
For use when starting problems is present.
|
| Alcohol Density Estimate
|
Alcohol density estimate
|
-
|
| Alcohol Density Learning
|
Status of the alcohol density learning
|
-
|
| Fuel Remaining Volume
|
Fuel remaining volume
|
-
|
| Vehicle Spec Signal 1
|
Status of the Vehicle Spec Judge Signal 1
|
-
|
| Electrical Load Signal 1
|
Electrical load signal
|
-
|
| Electrical Load Signal 2
|
Electrical load signal
|
-
|
| Cruise Cancel Signal
|
Status of the cruise cancel signal
|
-
|
| A/F Sensor Determination (worst value) #1
|
Worst judgment value of air fuel ratio sensor output for bank 1
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| A/F Sensor Determination (worst value) #2
|
Worst judgment value of air fuel ratio sensor output for bank 2
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #1
|
Worst value of average engine speed fluctuation (Cylinder 1)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #2
|
Worst value of average engine speed fluctuation (Cylinder 2)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #3
|
Worst value of average engine speed fluctuation (Cylinder 3)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #4
|
Worst value of average engine speed fluctuation (Cylinder 4)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #5
|
Worst value of average engine speed fluctuation (Cylinder 5)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #6
|
Worst value of average engine speed fluctuation (Cylinder 6)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #7
|
Worst value of average engine speed fluctuation (Cylinder 7)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| Engine Speed Fluctuation Avg (worst value) #8
|
Worst value of average engine speed fluctuation (Cylinder 8)
|
·
The worst value detected during monitoring is displayed.
·
The value is reset when DTCs are cleared.
|
| SPD (NT)
|
Input shaft speed
|
Data is displayed in increments of 50 rpm.
|
| SPD (SP2)
|
Output shaft speed
|
-
|
| Overdrive Cut Switch #1
|
Status of the overdrive cut switch
|
-
|
| Shift SW Status (P Range)
|
Park/Neutral position switch status (P)
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (R Range)
|
Park/Neutral position switch status (R)
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N Range)
|
Park/Neutral position switch status (N)
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported
|
Status of park/neutral position switch (N or P) supported
|
-
|
| Shift SW Status (N,P Range)
|
Park/Neutral position switch status (N or P)
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Sports Shift Up SW
|
Sport shift up switch status
|
-
|
| Sports Shift Down SW
|
Sport shift down switch status
|
-
|
| Sports Mode Selection SW
|
Sport mode select switch status
|
-
|
| Shift SW Status (D Range)
|
Park/Neutral position switch status (D)
|
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| A/T Oil Temperature 1
|
No. 1 ATF temperature sensor value
|
If value -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit open or shorted.
|
| A/T Oil Temperature 2
|
No. 2 ATF temperature sensor value
|
If value -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit open or shorted.
|
| ATF Thermal Degradation Estimate
|
Estimated value of ATF thermal degradation
|
If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected.
Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
|
| Lock Up
|
Lock-up
|
-
|
| Shift Status
|
ECM gear shift command
|
-
|
| SLT Solenoid Status
|
Shift solenoid SLT status
|
-
|
| SLU Solenoid Status
|
Shift solenoid SLU status
|
-
|
| Torque Converter Temperature Raise History
|
Torque converter temperature raise history status
|
This item always displays OFF.
|