Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P109C  Open in Fuel Pressure Switching Valve Circuit  P109D  Short in Fuel Pressure Switching Valve Circuit  


DESCRIPTION

A Flexible Fuel Vehicle (FFV) can be used with a fuel containing a high concentration of ethyl alcohol.

This FFV uses a fuel pressure switching system which changes the fuel pressure to low or high using a fuel pressure switching valve.

DTC No. DTC Detection Condition Trouble Area
P109C The fuel pressure switching valve relay circuit is open or shorted to ground.
(1 trip detection logic)
·

Fuel pressure switching valve circuit

·

F/PMP VSV relay

·

ECM


P109D The fuel pressure switching valve relay circuit is shorted to the power supply.
(1 trip detection logic)
·

Fuel pressure switching valve circuit

·

F/PMP VSV relay

·

ECM



MONITOR DESCRIPTION

These DTCs are stored when a malfunction is detected in the fuel pressure switching valve circuit. If the voltage of the fuel pressure switching valve circuit is different from the voltage commanded by the ECM, the ECM determines that the fuel pressure switching valve circuit is open or shorted, and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

HINT:

Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.


4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 3 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P109C or P109D.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A196240E05
5.706,0.889 6.125,1.059 0.420,0.170 10 MREL 5.378,0.778 5.666,0.934 0.288,0.156 10 A24 5.416,0.618 5.609,0.774 0.193,0.156 10 34 5.706,2.865 6.125,3.035 0.420,0.170 10 FPCR 5.378,2.866 5.666,3.022 0.288,0.156 10 D74 5.416,2.706 5.609,2.862 0.193,0.156 10 60 6.154,3.472 6.495,3.637 0.341,0.165 10 ECM 4.134,0.534 4.788,0.690 0.654,0.156 10 EFI NO. 2 3.707,2.122 4.488,2.278 0.781,0.156 10 F/PMP VSV 4.589,1.749 4.699,1.901 0.110,0.151 10 5 4.589,2.521 4.699,2.673 0.110,0.151 10 3 5.113,1.749 5.222,1.901 0.110,0.151 10 2 2.788,2.764 2.898,2.915 0.110,0.151 10 2 5.113,2.521 5.222,2.673 0.110,0.151 10 1 3.571,2.767 3.681,2.918 0.110,0.151 10 1 2.969,2.767 3.079,2.918 0.110,0.151 10 E 3.319,2.767 3.494,2.918 0.174,0.151 10 +B 2.334,3.069 2.559,3.230 0.225,0.161 10 R9 2.334,3.212 4.252,3.384 1.917,0.172 10 Fuel Pressure Switching Valve 0.795,3.817 1.263,3.987 0.468,0.170 10 Battery 1.888,1.562 2.974,1.738 1.086,0.177 10 Integration Relay 2.822,1.099 3.165,1.269 0.343,0.170 10 EFI 1.741,0.539 2.389,0.709 0.649,0.170 10 EFI NO. 1 1.188,0.776 1.413,0.932 0.225,0.156 10 1B 1.234,0.61 1.339,0.766 0.105,0.156 10 3 3.532,0.776 3.757,0.932 0.225,0.156 10 1B 3.578,0.61 3.683,0.766 0.105,0.156 10 2 3.532,0.417 3.757,0.573 0.225,0.156 10 1B 3.578,0.251 3.683,0.407 0.105,0.156 10 4 1.178,0.417 1.403,0.573 0.225,0.156 10 1C 1.224,0.251 1.329,0.407 0.105,0.156 10 1

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT RELAY (F/PMP VSV)
B016200

a.

Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω




OK

2.INSPECT RELAY (POWER SOURCE VOLTAGE)

NG

REPLACE RELAY (F/PMP VSV)

2.INSPECT RELAY (POWER SOURCE VOLTAGE)
A196241E01
0.12,0.091 1.832,0.282 1.711,0.190 10 Engine Room Relay Block: 1.037,1.353 1.841,1.509 0.804,0.156 10 F/PMP VSV

a.

Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F/PMP VSV relay (2) - Body ground Ignition switch ON 11 to 14 V
F/PMP VSV relay (5) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - EFI RELAY)
3.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - ECM)
a.

Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F/PMP VSV relay (1) - D74-60 (FPCR) Always Below 1 Ω
F/PMP VSV relay (1) or D74-60 (FPCR) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (F/PMP VSV RELAY - EFI RELAY)
a.

Remove the integration relay (EFI) from the engine room relay block.


b.

Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F/PMP VSV relay (2) - 1B-4 Always Below 1 Ω
F/PMP VSV relay (5) - 1B-4 Always Below 1 Ω
F/PMP VSV relay (2) or 1B-4 - Body ground Always 10 kΩ or more
F/PMP VSV relay (5) or 1B-4 - Body ground Always 10 kΩ or more




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR