Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL SYSTEM
RM27M0U _51 Engine / Hybrid System _049097 3UR-FE FUEL _0233964 FUEL SYSTEM L

3UR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

·

Do not smoke or be near an open flame when working on the fuel system.

·

Keep gasoline away from rubber and leather parts.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the fuel pump ECU connector (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>REMOVAL).


c.

Connect the cable to the negative (-) battery terminal.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/0174 (system too lean) may be set.



e.

Crank the engine again, and then check that the engine does not start.


f.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


g.

Connect the fuel pump ECU connector (See page Engine / Hybrid System>3UR-FE FUEL>FUEL PUMP ECU>INSTALLATION).



FUEL SYSTEM


a.

When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

i.

Perform the "DISCHARGE FUEL SYSTEM PRESSURE" procedures above.


ii.

Put a container under the connecting part of the pressure line.


iii.

Slowly loosen the connection.


iv.

Disconnect the connection.


v.

Plug the connection with a rubber plug.



b.
A163532E08
1.167,1.198 1.438,1.448 false 0.719,3.385 0.625,3.719 false 0.76,1.188 0.635,1.438 false 1.125,3.406 1.438,3.969 false 1.208,0.073 2,0.281 0.792,0.208 10 false CORRECT 1.188,2.073 2.094,2.229 0.906,0.156 10 false INCORRECT 0.885,4.01 1.823,4.219 0.938,0.208 10 false Delivery Pipe 0.25,3.74 0.792,3.979 0.542,0.24 10 false O-Ring 0.323,1.469 0.927,1.708 0.604,0.24 10 false O-Ring 1.063,1.521 2,1.729 0.938,0.208 10 false Delivery Pipe

Observe these precautions when removing and installing the injectors:

·

Never reuse the O-ring.

·

When placing a new O-ring on the injector, do not damage it.

·

Coat a new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.



c.
A163533E08
1.229,2.802 1.646,2.802 false 1.031,0.563 1.323,0.563 false 1.521,1.073 0.781,1.073 false 1.792,1.865 2.542,1.865 false 1.958,2.281 2.594,2.281 false 0.188,0.458 1.063,0.688 0.875,0.229 10 false Delivery Pipe 0.281,0.99 0.802,1.177 0.521,0.188 10 false O-Ring 2.615,1.781 3.115,1.948 0.5,0.167 10 false Injector 2.625,2.188 3.271,2.396 0.646,0.208 10 false Insulator 0.281,2.719 1.24,2.906 0.958,0.188 10 false Cylinder Head

Install the injector to the delivery pipe and intake manifold as shown in the illustration.

NOTICE:

Before installing the injector, apply spindle oil or gasoline on the place where the delivery pipe contacts the O-ring of the injector.



d.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

i.
A157617E13
0.583,1.115 0.885,1.281 0.302,0.167 10 false Pull 0.167,0.167 2.042,0.729 1.875,0.563 12 false for Fuel Hose Connector Cover Type:

for Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.


ii.
A308865E09
0.479,1.917 0.354,1.917 0.354,1.917 0.479,1.396 false 0.51,1.823 1.604,2.01 1.094,0.188 10 false Fuel Pipe Clamp 0.24,0.083 2.979,0.448 2.74,0.365 12 true for Fuel Pipe Clamp Type:

for Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A088336E51
1.042,0.135 1.49,0.333 0.448,0.198 10 false Pinch 1.708,1.74 2.229,1.938 0.521,0.198 10 false Pinch 0.281,1.823 0.594,2.031 0.313,0.208 10 true Pull

Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:

Do not use any tools.



v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



e.
A130944E01
2.381,1.287 2.729,1.444 0.348,0.158 10 Push

Observe these precautions when connecting the fuel tube connector (for quick type A).

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.


iii.
A130945E02
2.392,1.393 2.659,1.548 0.267,0.155 10 Pull

After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.


iv.
A308865E10
0.479,1.917 0.354,1.917 0.354,1.917 0.479,1.396 false 0.51,1.823 1.604,2.01 1.094,0.188 10 false Fuel Pipe Clamp 0.26,0.125 2.927,0.438 2.667,0.313 12 true for Fuel Pipe Clamp Type:

for Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the connector.


v.
A157616E07
0.448,1.094 0.823,1.271 0.375,0.177 10 false Push 0.24,0.115 2.125,0.625 1.885,0.51 12 false for Fuel Hose Connector Cover Type:

for Fuel Hose Connector Cover Type:

Attach the lock claw to the connector by pushing down on the cover as shown in the illustration.


vi.

Check that there is no fuel leakage.



f.

Observe these precautions when disconnecting the fuel tube connector (for quick type B).

i.

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.


ii.
A308868E04
1.281,1.552 0.781,1.552 0.781,1.552 0.781,1.125 false 1.156,1.125 1.156,1.552 false 2.573,0.219 2.688,0.219 2.688,0.219 2.771,0.448 false 2,0.135 2.604,0.302 0.604,0.167 10 false Retainer 1.333,1.469 1.625,1.635 0.292,0.167 10 false Tab 1.146,0.271 1.469,0.448 0.323,0.177 10 false Pull 0.115,1.167 0.635,1.344 0.521,0.177 10 false Spread 1.281,1.177 1.802,1.354 0.521,0.177 10 false Spread

Spread the tabs of the retainer outward and pull the retainer upwards to disconnect the connector from the pipe.

HINT:
·
A308884E03
1.854,2.26 1.708,2.26 1.708,2.26 1.542,2.594 false 0.51,1.229 0.51,1.479 0.51,1.479 0.594,1.479 false 2.458,0.688 2.458,0.333 2.458,0.333 2.542,0.333 false 1.906,2.177 2.781,2.365 0.875,0.188 10 false Service Hole 0.646,1.396 1.26,1.583 0.615,0.188 10 false Retainer 0.24,0.438 0.552,0.604 0.313,0.167 10 false Pull 2.594,0.24 3.208,0.427 0.615,0.188 10 false Retainer

The connector can also be disconnected from the pipe by inserting a screwdriver with a blade of 4 mm or less into the service hole in the back of the retainer and pulling the retainer upwards.

·
A308869

If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.




iii.

Check for foreign matter on the seal surface of the disconnected pipe. Clean if necessary.


iv.

To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.



g.

Observe these precautions when connecting the fuel tube connector (for quick type B).

i.

Check for foreign matter on the pipe and around the connector before connecting it. Clean if necessary.


ii.
A308870E04
2.375,1.542 2.375,1.438 2.375,1.438 2.865,1.323 false 2.063,1.573 2.656,1.75 0.594,0.177 10 false Retainer 1.313,1.823 1.698,2 0.385,0.177 10 false Push 0.667,0.417 1.052,0.594 0.385,0.177 10 false Push

A308871E01
1.974,1.796 2.279,1.963 0.305,0.166 10 Pull

Align the axis of the connector with the axis of the pipe. Push the connector onto the pipe, and then push in the retainer until a "click" sound is heard.

NOTICE:
·

Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.




iii.

Check that there is no fuel leakage.



h.

Observe these precautions when disconnecting the fuel tube connector (for quick type C).

i.

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.


ii.
A293606E03
3.208,0.135 3.344,0.135 3.344,0.135 3.188,1.24 false 2.281,1.292 2.146,1.292 2.146,1.292 2.042,1.198 false 1.708,1.563 2.25,1.729 0.542,0.167 10 false Pull out 1.385,0.25 1.708,0.427 0.323,0.177 10 false Pull 2.594,0.063 3.177,0.24 0.583,0.177 10 false Retainer 2.51,0.885 2.813,1.063 0.302,0.177 10 false Pull 2.333,1.198 2.625,1.365 0.292,0.167 10 false Tab

Pull the tabs of the fuel tube connector retainer and pull up as shown in the illustration to disconnect the fuel tube connector from the pipe.


iii.
A293524

If the connector and pipe are stuck together, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.

NOTICE:
·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to free it. Then disconnect the main tube.




iv.

Check the sealing surface of the disconnected parts, and clean them if necessary.


v.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



i.

Observe these precautions when connecting the fuel tube connector (for quick type C).

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.

Line up the pipe and connector and push them together until a "click" sound is heard. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.
A293526E02
3.156,1.156 3.354,0.25 3.354,0.25 3.208,0.25 false 1.813,0.083 2.281,0.323 0.469,0.24 10 true Push 1.552,1.573 2,1.76 0.448,0.188 10 false Insert 2.604,0.167 3.208,0.344 0.604,0.177 10 false Retainer

Push down the retainer.


iv.
A293527E02
1.917,1.688 2.531,1.885 0.615,0.198 10 false Pull

After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.


v.

Check that there is no fuel leakage.




CHECK FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).