Home › Engine / Hybrid System › 1UR-FE FUEL › FUEL INJECTOR
RM27M0U _51 Engine / Hybrid System _049098 1UR-FE FUEL _0233966 FUEL INJECTOR A

1UR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the fuel pump ECU connector (See page Engine / Hybrid System>1UR-FE FUEL>FUEL PUMP ECU>REMOVAL).


c.

Connect the cable to the negative (-) battery terminal.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/0174 (system too lean) may be set.



e.

Crank the engine again, and then check that the engine does not start.


f.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


g.

Connect the fuel pump ECU connector (See page Engine / Hybrid System>1UR-FE FUEL>FUEL PUMP ECU>INSTALLATION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 25625 4.REMOVE EGR VALVE BRACKET

Hide 23902 5.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A214310

Disconnect the No. 2 fuel tube sub-assembly from the fuel pressure regulator assembly (for Quick Type A) (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A214311

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly RH (for Quick Type A) (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.
A214312

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly LH (for Quick Type A) (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23801P 7.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A308873

Detach the clamp.


b.

Disconnect the No. 1 fuel pipe sub-assembly from the fuel delivery pipe sub-assembly LH (for Quick Type B) (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23807 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH

a.

Disconnect the No. 6 wire harness connector.


b.
A308874

Remove the 2 bolts and fuel delivery pipe sub-assembly RH.

NOTICE:

When removing the fuel delivery pipe sub-assembly RH, hold the pipe by both ends and pull it straight upward.



c.

Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head sub-assembly RH.


Hide 23808 9.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH

a.

Disconnect the No. 7 wire harness connector.


b.
A214316

Remove the 2 bolts and fuel delivery pipe sub-assembly LH.

NOTICE:

When removing the fuel delivery pipe sub-assembly LH, hold the pipe by both ends and pull it straight upward.



c.

Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head sub-assembly LH.


Hide 23250 10.REMOVE FUEL INJECTOR ASSEMBLY

a.
A161427

Remove the fuel injector assembly from the fuel delivery pipe sub-assembly, and then disconnect the injector connector.

NOTICE:
A380111

For reinstallation, attach a tag or label to the injector shaft.



b.
A149190E01
2.549,1.735 3.077,1.909 0.527,0.173 10 O-Ring 2.852,1.454 2.852,1.704 false

Remove the O-ring from the fuel injector assembly.


c.
A214317

Detach the 3 clamps and then remove the No. 6 wire harness from the fuel delivery pipe sub-assembly RH.


d.
A214318

Detach the 3 clamps and then remove the No. 7 wire harness from the fuel delivery pipe sub-assembly LH.