Home › Engine / Hybrid System › 3UR-FE EMISSION CONTROL › EMISSION CONTROL SYSTEM
RM27M0U _51 Engine / Hybrid System _049100 3UR-FE EMISSION CONTROL _0233980 EMISSION CONTROL SYSTEM G

3UR-FE EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL CUT-OFF OPERATION

a.

Start and warm up the engine.


b.

Open the throttle valve and keep the engine speed at 3000 rpm.


c.

Use a sound scope to check for injector operating noise.


d.

Check that when the accelerator pedal is released, injector operation noise stops momentarily and then resumes.

If the result is as not specified, check the injector, wiring and ECM.


Hide 2.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Check that there are no cracks, leaks or damage.

HINT:

Separation of the engine oil dipstick, oil filler cap, ventilation hose, etc. may cause an engine failure or engine malfunctions. Disconnection, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will allow air suction and cause an engine failure or engine malfunctions.


NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, ventilation hose and other components may cause the engine to run improperly.

·

Disconnection, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will allow air suction and cause an engine failure or engine failure malfunctions.



If the result is not as specified, replace parts as necessary.


Hide 3.INSPECT FUEL CUT-OFF VALVE AND FILL CHECK VALVE

a.

Disconnect the vent line hose from the charcoal canister.

A273966E01
1.09,1.143 1.47,1.143 false 2.435,0.257 2.618,0.430 0.183,0.173 10 *2 2.65,2.398 2.832,2.571 0.183,0.173 10 *3 0.915,1.072 1.098,1.246 0.183,0.173 10 *1 2.82,2.462 3.063,2.462 3.063,2.462 3.549,2.158 false 2.614,0.327 2.972,0.327 2.972,0.327 4.239,1.83 false

Text in Illustration
*1 Fuel Tank Cap *2 Charcoal Canister
*3 Vent Line Hose - -


b.

Connect a pressure gauge to the vent line hose.


c.

Fill the fuel tank with fuel.


d.

Apply a pressure of 4 kPa (41 gf/cm2, 0.6 psi) to the vent port of the fuel tank.

HINT:

When the fuel tank is full, the float valve of the fill check valve is closed and there is no ventilation. Therefore, it is necessary to check the fuel amount.



e.

Remove the fuel tank cap and check that the pressure inside the tank drops.

If the pressure does not drop, replace the fuel tank assembly.


f.

Reconnect the vent line hose to the charcoal canister.


Hide 4.CHECK AIR INLET LINE

a.
A273967

Disconnect the air inlet line hose from the charcoal canister.


b.

Check that there is ventilation in the air inlet line.

If air cannot flow freely into the air inlet line, repair or replace the air inlet line.


c.

Reconnect the air inlet line hose to the charcoal canister.


Hide 5.INSPECT PRESSURE SENSOR

A158647E06
1.76,0.167 1.01,0.729 false 1.76,0.167 1.083,2.313 false 1.854,0.073 2.927,0.51 1.073,0.438 10 true Pressure Gauge 0.063,0.052 1.031,0.448 0.969,0.396 12 true for Bank 1: 0.063,1.771 1.031,2.146 0.969,0.375 12 true for Bank 2:

a.

Connect a pressure gauge to the air pressure sensor as shown in the illustration.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream ON.


d.

Enter the following menus:

Select: Powertrain / Engine and ECT / Data List / All Data / Air pump pressure (absolute).


e.

Check that the pressure displayed on the tester fluctuates when applying pressure to the pressure sensor with the pressure gauge.

OK:

Pressure fluctuates in response to pressure applied with pressure gauge.


HINT:

The tester displays the air pump pressure (AIR PMP PRS (A) and AIR PMP2 PRS (A)) as absolute pressure.


NOTICE:

When applying pressure, make sure that no foreign matter enters the sensor.



f.
U151428E01
0.083,0.058 2.434,0.422 2.350,0.364 10 Front view of wire harness connector: (to Air Switching Valve) 0.172,1.6 0.458,1.739 0.286,0.139 10 D58 0.172,1.898 0.458,2.037 0.286,0.139 10 D59 0.56,1.603 0.748,1.764 0.188,0.161 10 *1 0.56,1.901 0.748,2.062 0.188,0.161 10 *2 0.185,2.598 1.044,2.763 0.860,0.165 10 *1: for Bank 1 0.185,2.987 1.072,3.152 0.887,0.165 10 *2: for Bank 2 1.434,2.596 1.655,2.752 0.220,0.156 10 VC 2.206,2.596 2.397,2.750 0.191,0.154 10 E2 1.434,2.812 1.738,2.969 0.304,0.156 10 VC2 2.206,2.812 2.489,2.967 0.284,0.154 10 E22 1.565,2.05 1.565,2.566 false 1.913,2.05 2.307,2.566 false 1.701,2.596 1.889,2.756 0.188,0.161 10 *1 2.433,2.596 2.622,2.756 0.188,0.161 10 *1 1.799,2.812 1.987,2.973 0.188,0.161 10 *2 2.546,2.812 2.735,2.973 0.188,0.161 10 *2

Check the power source voltage.

i.

Disconnect the connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D58-2 (VC) - D58-4 (E2) Ignition switch ON 4.75 to 5.25 V
D59-2 (VC2) - D59-4 (E22)