Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › CYLINDER BLOCK
RM27M0U _51 Engine / Hybrid System _049105 3UR-FBE ENGINE MECHANICAL _0234013 CYLINDER BLOCK A

3UR-FBE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A160740

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.15 to 0.55 mm (0.00591 to 0.0217 in.)


Maximum thrust clearance:

0.70 mm (0.0276 in.)


If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.

If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Check that the front mark on the connecting rod and cap are aligned to ensure correct reassembly.


b.
A161898

Remove the 2 connecting rod cap bolts.


c.
A161899

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted to the connecting rod cap.



d.

Clean the crank pin and bearing.


e.

Check the crank pin and bearing for pitting and scratches.

If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.


f.
A161900

Lay a strip of Plastigage on the crank pin.


g.
A161901E04
1.635,0.76 1.177,1.229 1.177,1.229 0.958,1.229 true 0.021,0.49 0.406,0.667 0.385,0.177 10 false Front 0.125,1.146 0.896,1.354 0.771,0.208 10 true Front Mark

Check that the front mark of the connecting rod cap is facing forward.


h.
A161902

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not turn the crankshaft.



i.
A101478E37
2.063,0.74 2.167,0.156 2.167,0.156 2.302,0.156 false 0.604,1.385 1.104,1.583 0.5,0.198 10 false Front 2.323,0.073 3.354,0.271 1.031,0.198 10 false Painted Mark 1.146,0.302 1.49,0.49 0.344,0.188 10 false 90°

Mark the front side of each connecting rod cap bolt with paint.


j.

Tighten the cap bolts another 90° as shown in the illustration.


k.

Check that the painted marks are now at a 90° angle to the front.

NOTICE:

Do not turn the crankshaft.



l.
A161898

Remove the 2 connecting rod cap bolts.


m.
A161899

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted to the connecting rod cap.



n.
A380014E01
1.375,1.635 1.521,1.635 1.521,1.635 1.917,2.625 true 4.604,1.74 4.604,1.458 true 5.667,2.677 5.667,2.083 true 6.323,2.646 6.323,2.5 6.323,2.5 5.729,2.104 true 5.115,2.573 5.292,2.573 5.292,2.573 5.625,2.052 true 4.969,2.313 5.125,2.313 5.125,2.313 5.594,2.042 true 5.656,4.385 4.396,4.385 4.396,4.385 4.396,3.938 true 5.656,4.385 5.656,3.854 true 5.552,4.385 5.552,3.667 true 4.979,4.521 4.979,4.385 true 0.677,1.531 2.208,1.729 1.531,0.198 10 false Plastigage 4.188,1.75 5.875,1.948 1.688,0.198 10 false Number Mark 4.604,2.229 5.375,2.427 0.771,0.198 10 false No. 4 4.75,2.51 5.521,2.708 0.771,0.198 10 false No. 3 5.51,2.688 6.281,2.885 0.771,0.198 10 false No. 2 6.167,2.646 6.938,2.844 0.771,0.198 10 false No. 1 4.594,4.51 6.281,4.708 1.688,0.198 10 false Number Mark

Measure the Plastigage at its widest point.

Standard oil clearance:

0.025 to 0.050 mm (0.000984 to 0.00197 in.)


Maximum oil clearance:

0.070 mm (0.00276 in.)


If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.

HINT:
·

If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. Each bearing's standard thickness is indicated by a 1, 2, 3 or 4 mark on its surface.

·

Select the correct bearing by adding together the number marks imprinted on the connecting rod big end and crank pin.


Example:

Connecting rod "1" + Crank pin "2" = 3 (Use bearing "3")


Reference:

Standard sized bearing center wall thickness:
Mark Specified Condition
2 1.489 to 1.492 mm (0.0586 to 0.0587 in.)
3 1.492 to 1.495 mm (0.0587 to 0.0589 in.)
4 1.495 to 1.498 mm (0.0589 to 0.0590 in.)
5 1.498 to 1.501 mm (0.0590 to 0.0591 in.)
6 1.501 to 1.504 mm (0.0591 to 0.0592 in.)
7 1.504 to 1.507 mm (0.0592 to 0.0593 in.)


Connecting rod big end inside diameter:
Mark Specified Condition
1 59.000 to 59.006 mm (2.32283 to 2.32306 in.)
2 59.007 to 59.012 mm (2.32311 to 2.32330 in.)
3 59.013 to 59.018 mm (2.32334 to 2.32354 in.)
4 59.019 to 59.024 mm (2.32358 to 2.32377 in.)


Crankshaft pin diameter:
Mark Specified Condition
1 55.995 to 56.000 mm (2.20452 to 2.20472 in.)
2 55.989 to 55.994 mm (2.20429 to 2.20448 in.)
3 55.982 to 55.998 mm (2.20401 to 2.20464 in.)



o.

Completely remove the Plastigage.


p.

Perform the inspection above for each cylinder.


Hide 3.REMOVE PISTON AND CONNECTING ROD

a.
A163455E05
0.906,1.75 0.906,1.521 0.906,1.521 1.521,1.156 true 0.427,1.771 1.375,2 0.948,0.229 10 true Ridge Reamer

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Remove the 16 cap bolts, 8 connecting rod caps and 8 lower bearings.


c.

Push the 8 pistons and 8 connecting rods through the top of the cylinder block.

HINT:

Arrange the piston and connecting rod in the correct order.



Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rods and connecting rod caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 5.REMOVE PISTON RING SET

HINT:

Arrange the piston rings in the correct order.


a.
A160692

Using a piston ring expander, remove the 2 compression rings.


b.

Remove the 2 side rails and oil ring expander by hand.


Hide 13101 6.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.

Disconnect the connecting rod from the piston.

i.
A160693

Using a small screwdriver, pry off the 2 snap rings from the piston.


ii.
A142805

Gradually heat the piston to approximately 80°C (176°F).


iii.
A142806

Using a brass bar and plastic-faced hammer, lightly tap out the piston pin. Then remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.





b.

Clean the piston.

i.
A160694

Using a gasket scraper, remove the carbon from the piston top.


ii.
A160695

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


iii.
A160696

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.




Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A163458

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.020 to 0.220 mm (0.000787 to 0.00866 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set.

Standard thrust washer thickness:

2.44 to 2.49 mm (0.0961 to 0.0980 in.)


If necessary, replace the crankshaft.


Hide 13411 8.REMOVE CRANKSHAFT

a.
A160705E05
3.302,0.927 3.427,1.104 0.125,0.177 10 false 1 2.042,1.948 2.167,2.125 0.125,0.177 10 true 2 3.042,1.177 3.167,1.354 0.125,0.177 10 true 3 2.458,1.75 2.583,1.927 0.125,0.177 10 true 4 2.75,1.469 2.875,1.646 0.125,0.177 10 true 5 0.396,1.313 0.521,1.49 0.125,0.177 10 true 6 1.646,0 1.771,0.177 0.125,0.177 10 false 7 0.677,0.5 0.802,0.677 0.125,0.177 10 false 8 1.365,0.073 1.49,0.25 0.125,0.177 10 true 9 0.99,0.354 1.177,0.531 0.188,0.177 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts and 10 seal washers in several steps, in the sequence shown in the illustration.


b.
A160706E09
3.094,1.49 3.188,1.646 0.094,0.156 10 true 1 3.021,0.271 3.115,0.427 0.094,0.156 10 false 2 0.208,1.594 0.302,1.75 0.094,0.156 10 false 3 0.281,0.24 0.375,0.396 0.094,0.156 10 false 4 2.49,1.542 2.583,1.698 0.094,0.156 10 true 5 2.406,0.219 2.5,0.375 0.094,0.156 10 true 6 0.771,1.573 0.865,1.729 0.094,0.156 10 true 7 0.833,0.271 0.927,0.427 0.094,0.156 10 true 8 1.927,1.573 2.021,1.729 0.094,0.156 10 true 9 1.271,0.281 1.458,0.438 0.188,0.156 10 true 10 3.177,1.156 3.365,1.313 0.188,0.156 10 false 11 3.104,0.656 3.292,0.813 0.188,0.156 10 false 12 0,1.177 0.188,1.333 0.188,0.156 10 false 13 0.042,0.635 0.229,0.792 0.188,0.156 10 false 14 2.563,1.146 2.75,1.302 0.188,0.156 10 true 15 2.5,0.646 2.688,0.802 0.188,0.156 10 true 16 0.615,1.156 0.802,1.313 0.188,0.156 10 false 17 0.708,0.781 0.896,0.938 0.188,0.156 10 true 18 1.927,1.021 2.115,1.177 0.188,0.156 10 true 19 1.26,0.771 1.448,0.927 0.188,0.156 10 true 20

Uniformly loosen and remove the 20 bearing cap bolts in several steps, in the sequence shown in the illustration.


c.
A163460E01
0.119,0.146 0.789,0.538 0.670,0.392 10 Protective Tape 0.206,2.836 0.788,3.226 0.582,0.390 10 Cylinder Block 2.81,2.591 3.332,2.962 0.522,0.371 10 Bearing Cap 0.605,4.125 1.498,4.336 0.892,0.211 10 Joint Surface 1.191,3.602 1.084,4.09 false 1.084,4.09 1.583,3.693 false 0.927,0.246 1.156,0.246 1.156,0.246 1.51,1.325 false

Using a screwdriver, slightly pry up the 5 main bearing caps.

NOTICE:
·

Be careful not to damage the joint surface of the cylinder block and main bearing caps.

·

Pry up the left and right side of the cap little by little.



HINT:
·

Tape the screwdriver tip before use.

·

Keep the lower bearing and crankshaft bearing cap together.




d.

Using 2 inside position main bearing cap bolts, loosen each main bearing cap by moving it forward and backward, and remove the 5 main bearing caps and 2 lower thrust washers (No. 3 crankshaft bearing cap only).

HINT:

Arrange the removed parts in the correct order.



e.

Remove the crankshaft.


Hide 11711 9.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings from the bearing caps and cylinder block.

HINT:

Arrange the removed parts in the correct order.



Hide 11011 10.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A150072

Remove the thrust washer set from the cylinder block and No. 3 bearing cap.


Hide 15708 11.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A142804

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.


Hide 12.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.