Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234039 CYLINDER BLOCK A

1UR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the piston or piston ring (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Using an E8 "TORX" socket wrench, install the stud bolts.

U151418E02
5.052,4.51 4.885,4.51 4.885,4.51 4.542,5.229 false 5.646,5.729 5.167,5.729 5.167,5.729 4.542,5.865 false 2.563,4.052 2.375,4.052 2.375,4.052 1.875,4.927 false 2.813,5.573 2.531,5.573 2.531,5.573 1.875,5.823 false 1.167,2.323 1.167,3.375 false 2.625,2.354 2.625,3.25 2.625,3.25 1.167,3.25 false 4.677,1.448 4.677,3.396 false 6.333,2.625 6.333,3.135 6.333,3.135 4.677,3.135 false 1.302,0.156 2.5,0.385 1.198,0.229 12 false for Upper Side: 4.688,0.156 5.865,0.385 1.177,0.229 12 false for Lower Side: 4.646,3.438 4.813,3.667 0.167,0.229 10 false A 1.135,3.458 1.333,3.635 0.198,0.177 10 false B 2.594,3.979 3.281,4.344 0.688,0.365 10 false 26.5 mm (1.043 in.) 2.844,5.51 3.573,5.885 0.729,0.375 10 false 18 mm (0.709 in.) 2.792,5.125 3.927,5.281 1.135,0.156 10 false 50 mm (1.969 in.) 1.365,6.177 1.531,6.406 0.167,0.229 10 false A 4.063,6.177 4.26,6.354 0.198,0.177 10 false B 5.49,5.094 6.188,5.469 0.698,0.375 10 false 29 mm (1.142 in.) 5.677,5.656 6.365,6.031 0.688,0.375 10 false 13 mm (0.512 in.) 5.083,4.427 6.24,4.635 1.156,0.208 10 false 14 mm (0.551 in.)

Torque:
for stud bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A142804

Using a 5 mm hexagon wrench, install the 4 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the piston sub-assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A214548E01
0.473,1.604 1.360,1.825 0.887,0.221 10 Service Hole 1.491,1.704 2.31,1.704 2.31,1.704 2.685,1.43 false

Using a small screwdriver, install a new snap ring at one end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole of the piston.



b.
A131877

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin and connecting rod with engine oil.


d.
A214549E02
2.219,0.344 2.385,0.344 2.385,0.344 2.75,0.688 true 2.24,2.625 2.385,2.625 2.385,2.625 2.76,2.521 true 0.927,1.26 0.927,2.135 true 0.927,3.344 0.927,4.219 true 0.115,0.146 0.427,0.344 0.313,0.198 10 false LH: 0.115,2.313 0.427,2.51 0.313,0.198 10 false RH: 1.51,0.26 2.25,0.458 0.74,0.198 10 false Front Mark 0.573,2.135 1.344,2.344 0.771,0.208 10 false Front Mark 0.573,4.229 1.344,4.438 0.771,0.208 10 false Front Mark 1.531,2.542 2.302,2.75 0.771,0.208 10 false Front Mark

Align the front marks of the piston and connecting rod as shown in the illustration. Then push in the piston pin with your thumb until the piston pin contacts the snap ring.

NOTICE:

For the LH side, perform the assembly so that the front marks of the piston and connecting rod are on the same side. For the RH side, perform the assembly so that the front marks of the piston and connecting rod are on opposite sides.


HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin.

i.
A214550

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.


ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.



f.
A214548E01
0.473,1.604 1.360,1.825 0.887,0.221 10 Service Hole 1.491,1.704 2.31,1.704 2.31,1.704 2.685,1.43 false

Using a small screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13011 4.INSTALL PISTON RING SET

HINT:

Perform " Inspection After Repairs" after replacing the piston ring (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A164414E08
1.51,0.594 1.688,0.594 1.688,0.594 1.906,0.896 false 1.521,1.677 1.677,1.677 1.677,1.677 1.792,1.385 false 1.99,1.135 2.604,1.375 2.604,1.375 2.604,1.51 false 0.5,0.5 1.563,0.667 1.063,0.167 10 false Side Rail Upper 0.51,1.583 1.573,1.75 1.063,0.167 10 false Side Rail Lower 1.906,1.552 3.135,1.75 1.229,0.198 10 false Oil Ring Expander

Install the oil ring expander and 2 side rails by hand.


b.

Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

A332528E02
1.896,0.365 2.24,0.135 2.24,0.135 2.354,0.135 false 1.417,3.052 1.083,1.75 1.083,1.75 0.917,1.75 false 2.052,2.031 1.083,1.75 false 6.031,1.292 6.135,1.427 6.135,1.427 6.135,1.5 false 6.031,2.625 6.135,2.76 6.135,2.76 6.135,2.844 false 4.25,1.938 4.104,2.156 4.104,2.156 4.104,2.26 false 2.563,2.49 3,2.917 3,2.917 3.125,2.917 false 2.01,3.135 2.448,3.469 2.448,3.469 2.573,3.469 false 2.406,0.063 3.823,0.24 1.417,0.177 10 false Piston Ring Expander 3.354,2.281 4.927,2.469 1.573,0.188 10 false No. 1 Compression Ring 5.365,1.5 6.938,1.698 1.573,0.198 10 false No. 2 Compression Ring 2.635,1.917 3.167,2.115 0.531,0.198 10 false Upward 0.219,1.688 0.927,1.844 0.708,0.156 10 false Paint Mark 5.094,0.542 5.667,0.74 0.573,0.198 10 false Type A: 5.094,1.833 5.667,2.031 0.573,0.198 10 false Type B: 5.365,2.854 6.938,3.052 1.573,0.198 10 false No. 2 Compression Ring 3.156,2.833 4.729,3.021 1.573,0.188 10 false No. 1 Compression Ring 2.615,3.396 4.188,3.583 1.573,0.188 10 false No. 2 Compression Ring

HINT:

Type A and type B can be distinguished by the color of the paint marks or the cross-section shape of the No. 2 compression ring.

Item Paint Mark
Type A No. 1 Compression Ring Blue
No. 2 Compression Ring Orange
Type B No. 1 Compression Ring Yellow
No. 2 Compression Ring Green



Hide 11711 5.INSTALL CRANKSHAFT BEARING

a.
A124282E26
0.344,0.458 1.5,0.813 1.156,0.354 10 false No. 1 and No. 5 Journal Bearings: 1.813,0.479 3.24,0.833 1.427,0.354 10 false No. 2, No. 3 and No. 4 Journal Bearings: 0.563,2.604 1.167,2.792 0.604,0.188 10 false 22.5 mm 2.448,2.583 2.906,2.771 0.458,0.188 10 false 21 mm

Clean the main journal and both surfaces of the bearing.


b.

Install the upper bearing.

NOTICE:

Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.


i.
A142825E01
1.236,3.881 1.975,4.056 0.739,0.174 10 CORRECT 2.227,3.881 3.115,4.056 0.887,0.174 10 INCORRECT

Install the upper bearing to the cylinder block as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.





c.
A149045E09
2.458,3.406 2.74,4.021 false 2.198,4.063 3.156,4.26 0.958,0.198 10 false Vernier Caliper 0.729,3.573 0.844,3.75 0.115,0.177 10 false A 2.177,3.594 2.302,3.771 0.125,0.177 10 false B

Install the lower bearing.

NOTICE:
·

Be sure to install the selected bearing.

·

Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.



i.

Install the lower bearings to the bearing caps.


ii.

Using a vernier caliper, measure the distance between the bearing cap's edge and the lower bearing's edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.





Hide 11011 6.INSTALL CRANKSHAFT THRUST WASHER SET

a.
A150072

Apply engine oil to the thrust washer set.


b.

Install the 4 thrust washers to the No. 3 journal position of the cylinder block and bearing cap with the oil grooves facing outward.


Hide 13411 7.INSTALL CRANKSHAFT

a.
U151460E02
1.802,2.708 1.802,3.042 false 2.292,2.896 2.292,2.708 false 1.333,2.896 1.333,2.708 false 1.375,3.052 2.26,3.229 0.885,0.177 10 false Number Mark

Apply engine oil to the upper bearing and lower bearing, then place the crankshaft on the cylinder block.


b.

Confirm the front marks and numbers of the main bearing caps, and install the bearing caps on the cylinder block.

HINT:

A number is marked on each main bearing cap to indicate the installation position.



c.

Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.


d.

Temporarily install the 10 main bearing cap bolts to the inside positions.


e.
A160709E01
2.185,2.9 2.645,3.061 0.460,0.161 10 91 mm 0.137,2.871 1.237,3.055 1.100,0.184 10 Less than 6 mm 0.768,2.862 0.768,2.689 0.768,2.689 1.167,2.221 false

Insert the main bearing cap by hand until the clearance between the main bearing cap and cylinder block is less than 6 mm (0.236 in.) by marking the 2 internal bearing cap bolts as a guide.

Bolt length:

91 mm (3.58 in.)



f.
U115329

Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 10 main bearing cap bolts.


h.
A160710E01
1.669,3.07 2.238,3.244 0.569,0.173 10 79.5 mm

Temporarily install the 10 main bearing cap bolts to the outside positions.

Bolt length:

79.5 mm (3.13 in.)


HINT:

The main bearing cap bolts are tightened in 2 progressive steps.



i.

Step 1:

i.
A160706E06
1.313,0.781 1.406,0.938 0.094,0.156 10 true 1 2.052,1.146 2.146,1.302 0.094,0.156 10 true 2 0.719,0.635 0.813,0.792 0.094,0.156 10 true 3 0.677,1.156 0.771,1.313 0.094,0.156 10 false 4 2.552,0.646 2.646,0.802 0.094,0.156 10 true 5 2.583,1.146 2.677,1.302 0.094,0.156 10 true 6 0.146,0.656 0.24,0.813 0.094,0.156 10 false 7 0.094,1.167 0.188,1.323 0.094,0.156 10 false 8 3.125,0.656 3.219,0.813 0.094,0.156 10 false 9 3.167,1.146 3.354,1.302 0.188,0.156 10 false 10 1.375,0.198 1.563,0.354 0.188,0.156 10 false 11 1.823,1.615 2.01,1.771 0.188,0.156 10 true 12 0.792,0.219 0.979,0.375 0.188,0.156 10 true 13 0.729,1.594 0.917,1.75 0.188,0.156 10 true 14 2.313,0.208 2.5,0.365 0.188,0.156 10 true 15 2.406,1.625 2.594,1.781 0.188,0.156 10 true 16 0.177,0.313 0.365,0.469 0.188,0.156 10 false 17 0.083,1.521 0.271,1.677 0.188,0.156 10 false 18 3,0.281 3.188,0.438 0.188,0.156 10 false 19 3.083,1.5 3.271,1.656 0.188,0.156 10 true 20

Uniformly tighten the 20 main bearing cap bolts in the sequence shown in the illustration.

Torque:
for inside position : 61 N*m (622 kgf*cm, 45 ft.*lbf)
for outside position : 27 N*m (275 kgf*cm, 20 ft.*lbf)

If any of the main bearing cap bolts do not meet the specified torque, replace it.



j.

Step 2:

i.
A132155E11
1.979,0.708 2.208,0.208 2.208,0.208 2.313,0.208 false 2.375,0.115 3.229,0.281 0.854,0.167 10 false Painted Mark 0.198,1.469 0.573,1.625 0.375,0.156 10 false Front 1.042,0.479 1.417,0.677 0.375,0.198 10 false 90°

Mark the front of the bearing cap bolts with paint.


ii.

Tighten the bearing cap bolts another 90° in the order shown in step 1.


iii.

Check that the painted marks are now at a 90° angle to the front.



k.

Check that the crankshaft turns smoothly.


l.
A160711E03
0.885,0.198 0.99,0.344 0.104,0.146 10 false 1 1.167,0.073 1.271,0.219 0.104,0.146 10 false 2 0.521,0.406 0.625,0.552 0.104,0.146 10 false 3 1.479,0.021 1.583,0.167 0.104,0.146 10 false 4 0.135,0.604 0.24,0.75 0.104,0.146 10 false 5 2.542,1.51 2.646,1.656 0.104,0.146 10 true 6 2.24,1.771 2.344,1.917 0.104,0.146 10 true 7 2.74,1.313 2.844,1.458 0.104,0.146 10 true 8 1.365,1.99 1.469,2.135 0.104,0.146 10 true 9 3.146,0.875 3.323,1.021 0.177,0.146 10 true 10

Install and uniformly tighten the 10 main bearing cap bolts and 10 new seal washers in several steps, in the sequence shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


m.

Check that the crankshaft turns smoothly.


Hide 13041 8.INSTALL CONNECTING ROD BEARING

A149047E01
1.872,3.545 1.982,3.711 0.110,0.165 10 A 3.104,3.545 3.260,3.724 0.156,0.179 10 B 0.874,2.197 1.845,2.380 0.971,0.184 10 Vernier Caliper 0.833,2.284 0.731,2.285 0.731,2.285 0.394,3.6 false

a.

Clean the connecting rod's bearing contact surface, cap's bearing contact surface and both surfaces of both bearings.


b.

Install the connecting rod bearings to the connecting rods and bearing caps.


c.

Using a vernier caliper, measure the distance between the connecting rod's and bearing cap's edges, and each connecting rod bearing's edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.




Hide 9.INSTALL PISTON AND CONNECTING ROD

a.
U151578E02
1.615,0.74 1.438,0.177 1.438,0.177 1.302,0.177 false 0.938,1.135 1.042,1.135 1.042,1.135 1.802,2.219 false 0.302,0.073 1.365,0.271 1.063,0.198 10 false Side Rail Upper 0.208,1.052 0.969,1.219 0.76,0.167 10 false Front Mark 0.24,2.344 0.938,2.542 0.698,0.198 10 false No. 2 Ring 2.458,2.354 3.083,2.729 0.625,0.375 10 false Side Rail Lower 2.74,1.208 3.167,1.625 0.427,0.417 10 false No. 1 Ring

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.

Position the piston rings so that the ring ends are as shown in the illustration.

HINT:

The expander ends can be placed anywhere.


NOTICE:

Do not align the ring ends.



c.
A214552E01
0.118,1.877 0.409,2.079 0.290,0.202 10 LH: 0.118,3.357 0.409,3.559 0.290,0.202 10 RH: 0.087,2.407 0.826,2.610 0.739,0.202 10 Front Mark 0.111,3.92 0.836,4.104 0.724,0.184 10 Front Mark 2.477,3.873 3.230,4.122 0.753,0.248 10 Front Mark 0.975,2.497 1.095,2.497 1.095,2.497 1.28,2.643 false 0.986,4.017 1.106,4.017 1.106,4.017 1.291,4.163 false 2.84,3.367 2.84,3.854 false

Using a hammer handle and piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.


d.

Place the connecting rod cap on the connecting rod.

i.
A214338E04
1.813,1.031 1.219,1.51 1.219,1.51 1,1.51 true 0.104,0.521 0.49,0.698 0.385,0.177 10 false Front 0.135,1.417 0.906,1.625 0.771,0.208 10 true Front Mark

Match the numbered connecting rod cap with the connecting rod.


ii.

Check that the front mark of the connecting rod cap is facing forward.

Front Mark:
Item Front Mark
LH Front Side
RH Rear Side




e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Temporarily install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A214339

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.
A132064E01
0.126,0.962 0.532,1.146 0.406,0.184 10 Front 2.378,0.034 3.228,0.190 0.850,0.156 10 Painted Mark 2.343,0.12 2.206,0.653 false 1.269,0.198 1.550,0.367 0.281,0.170 10 90°

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the cap bolts another 90° as shown in the illustration in the order in step 1.


iii.

Check that the painted marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.