Home › Engine / Hybrid System › 3UR-FE LUBRICATION › OIL AND OIL FILTER
RM27M0U _51 Engine / Hybrid System _049114 3UR-FE LUBRICATION _0234069 OIL AND OIL FILTER A

3UR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

a.
A150108

Remove the 3 screws and 5 bolts.


b.

Unhook the engine under cover from the vehicle body as shown in the illustration.


Hide 3.REMOVE OIL FILTER ELEMENT

a.
A380063E01
2.333,1.479 2.719,1.115 false 0.927,0.604 1.365,0.354 false 2.781,1 3.156,1.188 0.375,0.188 10 false Hose 1.438,0.24 1.813,0.427 0.375,0.188 10 false Pipe

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A162459

Remove the oil filter drain plug.


c.
A162460

Install the pipe to the oil filter cap.

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A162461

Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.


e.
A162462E01
2.437,1.439 2.763,1.609 0.326,0.170 10 SST 2.395,1.526 1.861,1.526 false

Using SST, remove the oil filter cap.

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip.



f.
A162463

Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



Hide 4.INSTALL OIL FILTER ELEMENT

a.
A162463

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.
A284602E04
2.802,0.76 2.729,0.76 2.729,0.76 2.656,1.042 false 1.208,0.688 1.135,0.688 1.135,0.688 1.01,0.938 false 0.281,1.583 1.021,1.75 0.74,0.167 10 false CORRECT 1.833,1.594 2.708,1.76 0.875,0.167 10 false INCORRECT 1.229,0.594 1.729,0.771 0.5,0.177 10 false O-Ring 2.823,0.667 3.323,0.844 0.5,0.177 10 false O-Ring

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element to the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.


f.
A284604E02
0.865,0.844 1.01,0.844 1.01,0.844 1.135,1.021 false 1.208,2.458 1.396,2.458 false 0.823,1.635 0.969,1.635 0.969,1.635 1.313,1.802 false 2.896,1.625 2.896,0.281 2.896,0.281 2.802,0.281 false 3.094,2.417 3.094,2.333 3.094,2.333 2.854,2.104 false 1.417,0.198 2.781,0.375 1.365,0.177 10 false Oil Filter Bracket Clip 0.292,0.75 0.875,1.094 0.583,0.344 10 false Oil Filter Bracket 0.271,1.531 0.781,1.708 0.51,0.177 10 false O-Ring 0.24,1.979 0.771,2.156 0.531,0.177 10 false No Gap 0.333,2.375 1.156,2.552 0.823,0.177 10 false Oil Filter Cap 2.927,2.438 3.24,2.594 0.313,0.156 10 false SST

Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

When tightening the oil filter cap, do not remove the oil filter bracket clip.

·

Make sure that the oil filter is installed securely as shown in the illustration.

·

Be careful that the O-ring does not get caught between any surrounding parts.

·

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.




g.
A162466

Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between any surrounding parts.



Hide 5.ADD ENGINE OIL

a.

Add fresh oil.

Standard Oil Grade (for U.S.A. and Canada):
Oil Grade Oil Viscosity (SAE)
ILSAC GF-5 multigrade engine oil 0W-20


Standard Oil Grade (for Mexico):
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC GF-5 multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40

·

20W-50




Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 7.1 liters (7.5 US qts, 6.2 Imp. qts)
Drain and refill with oil filter change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
Dry fill 9.3 liters (9.8 US qts, 8.2 Imp. qts)



b.

Install the oil filler cap.


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER

a.
A150108

Hook the engine under cover to the vehicle body as shown in the illustration.


b.

Install the 3 screws and 5 bolts.

Torque:
for bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for screw : 5.4 N*m (55 kgf*cm, 48 in.*lbf)